Search Documents

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

A detailed study of the capital investment and production cost for copper electrowinning plants shows that significant savings in both can be achieved by increasing the current density. From the economic analysis it is determined that the optimum current density which will result in lowest capital investment and lowest operating cost is between 60 A/sq. ft. and 70 A/sq. ft., or at least three times as high as the Conventionally employed current density. The specific investment, expressed as $/ton-year, is found to be a function of both the current density and plant capacity and has a minimum value at the optimum current density. Empirical equations are developed for the purpose of estimating the capital investment and operating cost for plants of any production capacity operating at any current density.

Jan 1, 1972

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By Christophe Bragard, Brett Robinson

This paper reflects the challenges encountered during the construction of the light rail tunnels under Boyle Heights, in Los Angeles, California. Equipped with two state-of-the-art EPB TBMs, the construction team undertook the mining of twin bored tunnels in the Los Angeles alluvium. The gassy underground conditions dictated many aspects of the design of the tunnels, as well as the tools and means used for their construction. This paper will detail the challenges encountered during construction, as well as the means, methods and logistics used on the project. Discussion includes: EPB TBM machines with some very unique/specific features; complex assembly sequence due to limited shaft access; final precast concrete liner with double gaskets; NATM cross passage excavation in soft ground and below the water table; compensation grouting; mucking shaft arrangement.

Jan 1, 2007

By Z. Hyder, M. Karmis

Underground or In-situ Coal Gasification (UCG or UICG), though not a new concept, is now attracting considerable global attention as a viable process to provide a "clean" and economic fuel from coal. Applying improved UICG technology to gasify deep, thin, and low-grade coal seams could vastly increase the amount of exploitable reserves. However, it is imperative that further development of this technology is based on integrating UCG practices and potential environmental impacts with accepted sustainability frameworks and processes. This paper evaluates the potential of UCG to conform to frameworks such as MMSD (Mining, Minerals and Sustainable Development), Natural Step and Green Engineering, in order to define its "sustainable" potential. The paper also discusses the potential contributions of UCG to sustainability during its design, operation, closure, and post-closure phases.

Jan 1, 2011

The Bureau of Mines, through its Minerals Availability Program (MAP), investigates the mineral supply potential of the United States and market economy countries (MEC's) for a number of minerals considered essential to the U.S. industrial base. Major activities include identification of important mines and mineral deposits, estimation of their mineral resources and production costs, and availability and sensitivity analyses. Products include data print-outs of geological and engineering information, discounted- cash-flow rate of return (DCFROR) analyses of individual mining operations, commodity availability appraisals, and analytic services to Government agencies. These products are used in assessing the mineral supply position of the United States: in setting priorities for research aimed at reducing production costs and minimizing adverse environ- mental impacts and regulatory compliance costs of mining and mineral processing operations; and in formulating and evaluating Government policies that affect minerals. Bureau MAP data and analyses have been provided to the executive and legislative branches to aid in consideration of trade, tax, and stockpile policy issues. A study of the economic potential of selected seabed mineral resources supports the regulatory responsibilities of the Department of the Interior in the U.S. Exclusive Economic Zone. Analytic studies of mineral project viability, industry competitiveness, and import dependencies were also undertaken for, or in cooperation with, U.S. and foreign government agencies, industry and trade organizations, and international lending institutions.

Jan 1, 1987

By Williams K. C

This paper presents a brief account of the plant which has been developed at Port Pirie to recover, by vacuum distillation, the greater part of the zinc content of desilverized lead. The present plant is an experimental unit, which is run in conjunction with the normal refinery practice, but can be cut out of the circuit. It will shortly be dismantled and duplicate units will be built on the sites chosen for the final plant installation.The unit described here has treated flows of 16 to 37 tons per hour of desilverized lead, to recover 90 to 95 per cent of the zinc contained in it. It is not intended here to detail all aspects of the vacuum dezincing operation, nor the developments which precededthe adoption of this design. The essential features of the present plant will be described and, where these are peculiar to the present experimental location, the intended alteration for the final plant will also be mentioned. OUTLINE OF PLANT AND PROCESSLead issues from the continuous desilverizing kettle at about 350° C. containing about 0·57 per cent Zn. It is conveyed by a tiled launder to the preheater, where it is heated to 580-620° C.Hot lead from the preheater enters the vacuum vessel via a barometric leg. From a reservoir holding about 19 tons of lead it falls by gravity in a thin film exposed to high vacuum (20-50 microns)3 and leaves the vessel via a barometric leg, entering the lead pot. The lead leaves this pot at 540-560° C., containing 0·03 to 0·06 per cent Zn, which is removed, together with residual antimony of 0.02 to 0·06 per cent, by a separate final refining process.

Jan 1, 1956

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

By Fisher N. I

Disequilibrium ratios (U3O8/eU3O8), which assess the degree to which gamma activity represents the uranium content of a sample, have been measured on a representative set of samples from the ore zone of a carnotite ranium deposit located at Yeelirrie, Western Australia. A statistical analysis has been performed to investigate the dependence of the ratios on lithology and on the location of the sample in the orebody. The analysis indicates that dependence on lithology and on position across the orebody is negligible. Samples from the western end of the orebody and those from below the water table level tend to have slightly lower ratios than samples from other positions, although these trends are small compared with a large random variation in the data. The large random variation could result from some redistribution of the daughter isotopes of uranium within the orebody. On the basis of the results from all the samples, the estimated deficiency of uranium relative to radium in the ore zone of the deposit is 11 per cent.

Jan 1, 1980

By A. M. R. Neiva

The WNW-ESE-trending hydrothermal veins cut alternating mica schists and quartzites of mainly Ordovician age and, to the west, a Hercynian muscovite-biotite granite. They have been prospected and developed to a depth of 300 m and reserves of 20 t Au estimated. The paragenetic sequence and chemical compositions of the ore minerals are generally similar to those at Jales to the south. Gold, electrum and aurian silver form inclusions in arsenopyrite, pyrite, galena, sphalerite, pyrrhotite and quartz and also occur in veinlets that cut these minerals. Silver has been found in gold, electrum, aurian silver, tetrahedrite, freibergite and the Ag-Pb-Sb sulphide owyheeite. Early arsenopyrite crystallised at an estimated 480 degrees C and the more common, later arsenopyrite in which Au and Ag are generally included at 430-300 degrees C. Sphalerite crystallised at 307-100 degrees C. Monoclinic pyrrhotite may have been formed by the inversion of hexagonal pyrrhotite at 248 degrees C

Jun 16, 1905

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By M. Wang, Z. Sui, T. Lou

After smelting, the associated mineral ore accompanying Valuable Metal Compounds (VMC),such as titania and borate in BF., most of the VMC were separated from the metal into the molten slag that is an associated slags. Based on several case studies in laboratories and in a practice in a pilot plant on the associated slags , there occur a feasibility to recovery VMC from the slags by anew process- Selective Precipitation Technique (SPT) on which three continuous steps are involved: (1) The selective enriching the dispersed VMC into a designed mineral phase in the molten slag; (2) The selective coarsening the designed mineral phase with large crystal grain size;(3) The selective separating the coarsen phase from tailing by mineral dressing or hydrometallurgical process . Some results on the recovering the VMC from the associated slags by SPT were summarized as examples in present paper. Keywords: selective precipitation technique, associated slag, recovering metals from slag.

Jan 1, 2004

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943

These may be of interest to members examining the collection of ores, etc., from Mount Lyell, which is a feature of the Victorian Gold Jubilee Exhibition, and may have some value as geological records. No. 7 and No 8 are analyses of samples of footwall rock from the Lyell Tharsis mine. No. 7 is hard, crystalline, fine-grained, and of homogenous structure. It has a dark-red colour, due to ferric oxide (Fig 1); and was taken from a place eight feet east of the ore body and about half way between the 50 feet and 100 feet levels. No. 8 is from the same excavation and from four feet east of the ore body it is softer than No. 7, being easily scratched with a knife-blade, of a deeper dark-red colour, and has a slaty cleavage.

Jan 1, 1902

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995

THE Phillips River gold and 'copper field is situated on the south coast of Western Australia, about 200 miles east of Albany, 180 miles west of Esperance, and: 250 miles south of Southern Cross, forming the southern extremity of what Mr. H. P. Woodward classes as the fourth belt of Pre-Cambrian rocks, and the first auriferous belt, whicf extends northward through Southern Cross, Mount Magnet, and Cue. The field may be considered the premier copper producer of the State. The first mineral discoveries were made about 1892; when gold, copper, and iron pyrites were found; but, owing to the isolation of the district and the scarcity of water, both in the locality and on the route thereto, little work was done for some years. In1899, however, payable gold reefs were opened up, and the district began to attract attention.The southern portion of the district is composed of limestone and sandstone rocks, forming the coastal series, and is for the most part flat, broken only by a few low hills and ridges, except to the west, where Cape Barren and Eyre's Range stand out...

Jan 1, 1917

The large increase in secondary industries in this country, during the war and post war periods, has caused a shortage of capacity for the production of merchant bar.To overcome this shortage, an expansion of rolling mill facilities has been undertaken by the Broken Hill Pty. Co. Ltd. A small, but modern, merchant mill has been erected at Kwinana in Western Australia and a strip and skelp mill is under construction at Newcastle. The latter mill will roll strip and skelp at present being rolled by the Newcastle 10 in. Merchant Mill, enahling this mill to concentrate on merchant bar production.The Kwinana mill was installed to supply the Western Australian market. This state has a small population (approximately 658,000) and is not at present highly industrialised. It was necessary, therefore, to design a mill which would be capable of producing a wide diversity of sections and could be expanded as the demand increased. To begin with capital expenditure had to be kept within reasonable bounds. The design work for this mill, with the exception of a few specialised items of equipment, was carried out at Newcastle.All design work for the Newcastle mill was carried out by the lVIorgan Construction Co. of America. Although initially intended for rolling flat. products, the designers were asked to make the mill as flexible as possible, so that should the market for flat products decrease, this mill with additional equipment could undertake the rolling of medium sized sections.

Jan 1, 1957

By R. Khanna, M. Dubikova

A variety of carbonaceous reducing materials are being used for the production of ferroalloys. Reductant materials include not just carbons such as coke, coal, char but also bio-carbons in form of charcoal produced from different types of wood. This paper discusses critical properties and reactions of carbonaceous materials and their significance in dictating reductant performance. Main considerations include among others, gasification of reductant, dissolution of carbon into molten metal, and direct reduction of slag by solid carbon. These are discussed in relation to material properties such as structural order, mineral matter content, composition, physical characteristics etc. A brief review of both conventional and novel approaches towards characterisation of carbonaceous materials has been included. Due to complexity and heterogeneity of carbonaceous reducing materials and a wide range of process requirements, the selection of the most appropriate reducing agent will depend on a number of considerations such as the availability of raw material and associated costs, product and process requirements and environmental aspects of waste gas emissions.

Jan 1, 2004

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006