Search Documents

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

By Jorge Beim

Helical Piles are increasingly being used to support and rehabilitate structures subjected to compressive axial loads. Traditionally, empirical correlations between installation torque and load capacity of helical screw piles are used as the field quality control. Load tests, however, are always recommended to validate the installation process and design methodology. This paper describes a test program performed on helical piles installed at the National Geotechnical Experimentation Site of the University of Massachusetts - Amherst campus (UMass-Amherst), well known for its deep varved clay deposit. Seven of these piles were submitted to Dynamic Load Tests using the Pile Driving Analyzer® (PDA), and also to Static Load Tests. Good agreements were obtained between the results of the dynamic and static load tests, encouraging the use of the former testing method as a viable alternative to the latter for determining the compressive load capacity of helical piles installed in cohesive soils. The results of the load tests were also compared to the predictions based on torque correlations, resulting in correlation coefficients which were higher than the ones traditionally used.

Jan 1, 2012

By V. McLemore, A. Fakhimi, K. Donahue, D. Sweeney, V. Viterbo

In order to evaluate the relationships between weathering and durability and strength of rock samples from the Goathill North rock pile at the Molycorp Questa mine, NM, we conducted slake durability and point load tests. Slake durability index (ID2) values ranged from 84 to 98%. Point load strength index (Is50) averaged for all rock units ranged from 1.1 to 5.7 MPa. Results show a slight positive trend between ID2 and paste pH. Two populations of data are distinguishable when ID2 is plotted versus the percentages of chlorite, illite and internal friction angle. In general, Is50 values increase toward the interior of the rock pile. Preliminary conclusions indicate that the durability and strength of the rock pile material generally increase toward the interior of the rock pile. Pre-rock pile alteration and post-rock pile weathering history have affected the durability of the GHN rock pile samples.

Jan 1, 2007

By William R. Yernberg

The 26th Peruvian Mining Convention (Convención de Ingeneieros de Minas del Perú) was held Sept. 15 through 19, 2003, in Arequipa. The convention was sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru). The Institute has been organizing these events since 1954. They are now held every other year. The conventions spotlight Peru’s mineral resources and have contributed to the tremendous growth of the Peruvian mining industry. This year’s meeting consisted of technical sessions, forums, field trips and social activities. It was held at the Tecsup Institute of Technology of Arequipa. More than 3,000 mining professionals attended. As always, the meeting was well organized, and participants expressed gratitude to the organizing committee for another successful meeting.

Jan 1, 2004

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By F Hancock

A rainfall simulator was developed to assist with hydrogeomorphic research into the stability of engineered landforms associated with rehabilitated uranium mines in the Top End of Australia. It can be used in rough terrain with slope gradients up to 30o. The rainfall simulator is modular, utilises upward jetting nozzles, has a multiple head arrangement and is capable of delivering rainfall intensities between 60 and 300 mmh-1 over areas up to 1000 m2 and could be easily modified for larger areas. Rainfall uniformity is commonly in excess of 80 per cent and the kinetic energy approaches that of natural rainfall (The modular design utilises an equilateral triangular array of rainfall stands, constructed from galvanised steel water pipes and flexible plastic hoses. Total construction costs are low. The water supply reservoir is mobile and easily constructed. An example of its use at Ranger Uranium Mine, investigating the effect of cover on rainsplash and rainwash dominated processes shows that vegetation cover is likely to reduce the erosion rate by these processes by at least four times below that experienced on bare areas.

Jan 1, 1997

By V. T. McLemore

Petrographic analysis of rocks is traditionally performed with optical microscopy using thin sections and point counting. However, this does not provide accurate mineral proportions for sedimentary, volcanic, and soil-like material, because rock fragments, groundmass, and matrix are not identified as specific minerals. In addition, groundmass phases in volcanic rocks can be too fine to identify individually, and making thin sections of intact soil-like material is difficult because much of the material is not well cemented. ModAn is a normative calculation that estimates modes ??by applying Gaussian elimination and multiple linear regression techniques to simultaneous mass balance equations? (Paktunc, 2001) and allows location-specific mineral compositions to be used. One of the features of ModAn that makes it appropriate for this study is that it can model one of several sulfide minerals. Mineral compositions for Questa minerals were determined from electron microprobe analysis and entered into ModAn. Then by combining and normalizing results, bulk quantitative mineralogy can be determined using ModAn, petrographic observations, electron microprobe analysis, clay mineral analysis, and the whole-rock chemistry of the sample.

Jan 1, 2009

In the early stages of opening up a mine, when there is some uncertainty as to its future career, necessitating caution in laying out works of a permanent character, the want is often felt of an assay furnace, easily built and easy of transportation, should the" mine " prove to be " no mine." Again, cases occur in which parties buy the right to treat comparatively small heaps of tailings, and then shift their plant to other localities. Under these circumstances it is necessary to restrict the plant to the barest necessaries, to suit, so to speak, the nomadic character of the work.An assay furnace that is really portable, easily transported, erected, taken down, of little weight, always ready for action on short notice, is indeed in these cases a desideratum which has long been wished for. The gasoline furnaces introduced intothe Australian market some time since practically fulfil these conditions; but they have the fatal drawback of being dependent on a constant supply of the liquid fuel, gasoline, which is seldom, if ever, obtainable locally in' any wayback mining township...

Jan 1, 1904

By ROLLIN THOMAS CHAMBERLIN

The studies herein reported were begun as a part of researches undertaken by the United States Geologü;al Survey looking to the more effcient utilization of the coal in the United States through the reduction of waste in its extnidion, and were continued as part of further researches having regard to the conservation of the fuel resources of this country and to the lessening of injuries and fatalities in coal mining. Among other phases of the general problem to be studied were the origin of the gas whidi escapes into coal mines, its modes of occurrence in the coal and rock strata, and the conditions governing its outflow into the mines. The subject of relative danger from destructive explosions due to gas and coal dust in different mines belonging to different coal fields was to be one of the principal lines of investigation. But this work was barely under way when the series of unusually disastrous explosions in the Naomi, .Monongah, and Darr mines of Pennsylvania and West Virginia, in December, 1907, afforded an exceptional occasion to observe the behavior of explosions on a large scale. Because of the opportunities for study afforded by these terrific explosions, the inquiry originally planned was d ¡verted to the more specific investigation of the conditions in tl10SC mines, and the examinations have been directed toward finding those qualities of gas and dust which were concerned in these explosions. The following discussion, therefore, consists essentially of a report on that subject; but it is far from being exhaustive, and is to be regarded as a preliminary outline of investigations which are still in progress. The first of the three mine explosions mentioned occurred in the Naomi mine of the United Coal Company, near Bellevernon, Pa., on Sunday, December 1, at 7.40 p. m. All the men who were within the mine at the time, fortunately only 34, were killed. Less than a week later there occurred in mines Nos. fì and 8 of the Fairmont Coal Company at Monongah, W. Va., the most disastrous mine explosion yet recorded in the annals of American mining. The mines were comparatively new and well laid out. Mine No.8 had been in operation only about two years and was the pride of the Fairmont Coal Company. Mine No.6 was first opened ahout four years earlier. In order to make it possible, in case of emergency, for either mine to be ventilated by the ventilating system of the other, the two sets of workings were connected underground. The F face heading of mine K o. 6 led direetly into No.2 north heading of No.8 mine. On Friday, Dcccmber 6, at about 10.30 in the morning, an explosion of unusual violcnce swept completely through both mines, pursuing its course throughout the numerous ramifications and bursting out of the two pit mouths, located It miles apart, nearly simultaneously. The slope of mine No.6 was only slightly damaged, but at the mouth of No.8 the destruction was very great. The fan was wrecked, the engine house was demolished, and mine timbers were blown across Monongahela River: As nearly as can be determined, 361 men were killed in the two mines by the explosion. .While the inspection of the Monongah mines was still in progress, on Thursday morning, December 19, at about 11.20, a similar explosion wrecked the Darr mine of the Pittsburgh Coal Company ut Jacobs Creek, Pu.; 238 men lost their lives in this explosion, which in number of casualties is second only to the :Monongah disustcr in the history of American mining. Of ull thc men in the mine at the , time of the explosion, only one mun, who happened to be within 100 feet of the ~iUrface on an old manway in a wet, unexploded portion of the mine, succeeded in escaping alive. The underground investigation of these mines was made in cooperation with Clarence Hall and ""Valter O. Snelling, of the United States Geological Survey, and James ""V. Paul, now of the Survey but at that time chief of the department of mines for vVest Virginia, to all of whom the author is greatly indebted for valuable assistance, suggestions, and advice. Mr. Paul will rcport on the nature of these explosions, the precipitating causes, their destructiveness, and the general cüliditions in these mines following the disasters. The present report is confined essentially to the laboratory examination of some of the explosive materials collected from these mines directly ufter the explosions.

Jan 1, 1911

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common-wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. Except for the mineral fuel commodities, the detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. In October 1977, responsibility for the collection of data on mineral fuels-coal, petroleum, natural gas, and natural gas liquids-was transferred to the newly created Department of Energy. Although chapters covering these commodities will no longer appear in Volume I of the Minerals Yearbook, quantity and value data have been included in most of these summary tables to maintain statistical consistency in State and national value of overall crude mineral output. This shift in responsibility has also resulted in changes to the composition of the "Nonmetals" and "Mineral Fuels" groups in table 1 and table 2. The commodities-asphalt and related bitumens (natural), carbon dioxide (natural), helium, and peat-have been removed from the "Mineral Fuels" group, and are now included under the "Nonmetals" group. There has been no change in the components of the "Metals" group.

Jan 1, 1980

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By Matthew A. Baumann

Tooth-wear on mining shovels requires continuous monitoring. Worn teeth impede excavation performance, increase energy usage, and increase the risk of lost or broken teeth and adapters. A machine-vision-based automated tooth-wear monitoring system is presented. The system employs a rugged boom or stick-mounted camera to capture images of the shovel teeth. An onboard computer processes the images in real-time to determine the length of each tooth. The current wear state is available via a network-accessible log for on-demand status updates. By continuously recording tooth length changes over time, the logs can be used to estimate wear rates and patterns, permitting comparisons between different G.E.T. configurations, operator behaviour patterns, or material types. This detailed, quantitative data permits site-specific optimizations to wear packages and maintenance scheduling. Automating wear monitoring offers the crucial wear information necessary to minimize maintenance costs and reduce unscheduled downtime. A 37-day field trial in a copper-gold mine demonstrated the ability of the system to measure tooth lengths, compute wear rates, and detect differences in tooth wear based on their position on the bucket.

Nov 1, 2011

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

By Rudy J. Matetic

Over-exposure to noise remains a widespread and serious health hazard in the U.S. mining industries despite 25 years of regulation. Every day, 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) noise level exceeds 85 dBA and more than 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the permissible exposure limit (PEL). Additionally, MSHA coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage comprise only seven different types of machines; auger miners, bulldozers, continuous miners, front end loaders, roof bolters, shuttle cars (electric), and trucks. In addition, the MSHA data indicate that the roof bolter is third among all the equipment and second among equipment in underground coal whose operators exceed 100% dosage. A research program was implemented to: 1) determine, characterize and to measure sound power levels radiated by a roof bolting machine during differing drilling configurations (thrust, rotational speed, penetration rate, etc.) and utilizing differing types of drilling methods in high compressive strength rock media (>20,000 psi). The research approach characterized the sound power level results from laboratory testing and provided the mining industry with empirical data relative to utilizing differing noise control technologies (drilling configurations and types of drilling methods) in reducing sound power level emissions on a roof bolting machine; 2) distinguish and correlate the empirical data into one, statistically valid, equation, in which, provided the mining industry with a tool to predict overall sound power levels of a roof bolting machine given any type of drilling configuration and drilling method utilized in industry; 3) provided the mining industry with several approaches to predict or determine sound pressure levels in an underground coal mine utilizing laboratory test results from a roof bolting machine and 4) described a method for determining an operators’ noise dosage of a roof bolting machine utilizing predicted or determined sound pressure levels.

Jan 1, 2006

By Conné Spangenberg

Contents ?Introduction ?Metal accounting environment ?Problem statement ?Investigations & Achievements ?Metal Accounting ?Principles ?Standards ?Audits ?Questions

Jan 1, 2005

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

By J. Konnerup-Madsen, T. Unlu, H. Stendal

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The region includes the Deveci siderite/goethite deposit and the Hasancelebi, Karakuz and Kuluncak magnetite/goethite deposits; Deveci is the only mine in operation. The area consists of a serpentine-gabbro complex overlain by a volcano-sedimentary sequence hosting the iron ores. At least three generations of hydrothermal alteration have affected all rock types except the latest trachytic dykes. The Deveci deposits occur in a pyroclastic volcano-sedimentary sequence with shales and carbonates equivalent to the main mafic sequence, whereas the other three deposits formed contemporaneously with the intrusion of trachytic dykes. The deposits are of the volcanic-exhalative type, with syngenetic siderite in pillow lavas or stratiform layers the primary and main Fe-bearing mineral. In the west hydrothermal alteration has replaced siderite in pillow lavas with magnetite or has remobilised sideritic iron into magnetite veins

Apr 1, 1995

By J. Matos e Silva

"Abstract Although one can think that it is very low the probability of a seism occurrence during the execution of an excavation in an urban lot protected by a diaphragm wall curtain, reality shows that whenever a seism occurs in an urban area several diaphragm walls will be affected by it. So it is advisable to consider the seismic action when designing a diaphragm wall curtain. The paper refers the main information about the seismic design of diaphragm walls according to the Eurocodes 7 and 8 and to the Portuguese Norms related to them (respectively NP EN 1997-1 2010 and NP EN 1998-5 2010), as the Eurocodes consider the possibility of each European country to adopt their own seismic parameters as the seismic risk is different in each country. Thus the so-called National Document of Application (in our case the Portuguese Norms) prescribes the seismic local parameters.1 - EUROCODES AND PORTUGUESE NORMS PRESCRIPTIONSAccording to Eurocode 8 - Part 5 and to the related Portuguese Norm NP EN 1998-5 2010, seismic actions on soils should be quantified adopting the Mononobe-Okabe method that gives goodapproaches when compared with reality.From paragraph 7.3.2.2 of the referred Norm, the horizontal seismic coefficient kh will be:"

Jan 1, 2014

Development of New Comminution Testing Methodologies for Geometallurgical Mapping of Ore Hardness and Throughput The emerging discipline of 'geometallurgy' is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing trend towards more effective mine site integration and optimisation. Constrained sampling that reflects and defines inherent ore body variability is a key geometallurgical requirement. This requires use of larger numbers of low-cost physical testing which can be applied to small sample volumes suitable for defining natural variability. The AMIRA P843 'GeMIII' project (Geometallurgical Mapping and Mine Modelling) is a major industry-supported research initiative designed to develop new tools, methods and protocols to support geometallurgical integration. As part of this integrated research a new more rapid low-cost comminution test (GeM Comminution index) has been developed which can be employed as a front line tool for geometallurgical mapping purposes and predictive throughput modelling. The test has been designed to be inserted into routine assay sample preparation and is based on constrained jaw crushing protocols linked to analysis of resultant size distributions. Extensive validation and modelling has shown the GeM Comminution Index (Ci) is correlated with the Drop Weight index A*b and Bond Mill Work Index (BMWi). Large scale trials have been conducted within a commercial assay laboratory to demonstrate and optimise incorporation of the Ci test into routine sample preparation protocols. While Ci based estimates of A*b and BMWi are not as precise compared to larger volume more expensive test-work, the ability to undertake large numbers of tests typically in a systematic down-hole manner, provides a high level of data support through adjacency. A Ci based approach is highly suitable for variability mapping, domaining and selecting large composite samples for more precise testing. Within the context of the AMIRA P843 project this forms part of an integrated work flow designed to support geometallurgical integration. The development of a comminution test linked to routine assay sample preparation represents significant value adding to a process that in most cases is already going to be carried out. This paper introduces the Ci test concept and application to geometallurgical testing for throughput modelling

Sep 13, 2010