Search Documents

By Luis Martín Tejeda

La simulación numérica es considerada como uno de los mejores métodos de modelamiento y planeamiento en la evaluación de la estabilidad de los taludes en minería superficial. En ese sentido, el presente texto señala que a través del método de tensión-deformación, implementado en programas computacionales basados en el método numérico de elementos finitos, se puede llegar a localizar la probable superficie de ruptura. Asimismo, con los diferentes modelos constitutivos como el elástico perfectamente plástico, estos taludes pueden ser evaluados. Por último, se describe brevemente los mecanismos de ruptura en taludes altos, el cálculo del FS y algunas características del programa de elementos finitos PLAXIS v. 7.2.

Sep 19, 2006

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By David M. Langlais, Krystle Pelham

"Explosives used in blasting operations, natural and anthropogenic sources such as septic systems,fertilizers, and decomposing vegetation can potentially contaminate groundwater with nitrate in thevicinity of construction sites and make identification of blasting impacts difficult. Blasting operationsfor a private construction project in Windham, New Hampshire were indicated as the source of water quality impacts to private drinking water wells prompting the New Hampshire Department ofTransportation (NHDOT) to implement a proactive approach to limit the potential for impacts fromblasting for ongoing NHDOT projects. NHDOT has developed a baseline drinking water monitoringprogram designed to detect potential impacts and to ensure alternative drinking water is providedthroughout the construction phase of projects. In 2013, the U.S. Geological Survey (USGS) andNHDOT began a study to determine the source and fate of nitrogen compounds near blasting sites using a combination of isotopic, time series, geochemical, hydrologic, and geologic data. Approximately 1.75 million cubic yards (1.33 cubic meters) of rock were removed by blasting in several locations for roadway construction at a major highway construction site in southern New Hampshire."

Jan 1, 2016

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By NORA Mining Sector Council

The National Occupational Research Agenda (NORA) is a partnership program to stimulate innovative research and workplace interventions. In combination with other initiatives, the products of this program are expected to reduce the occurrence of injuries and illnesses at work. Unveiled in 1996, NORA has become a research framework for the National Institute for Occupational Safety and Health (NIOSH) and the United States. Diverse parties collaborate to identify the most critical issues in workplace safety and health and develop research objectives for addressing those issues. NORA entered its third decade in 2016 with an enhanced structure. The 10 sectors formed for the second decade will continue to prioritize occupational safety and health research by major areas of the U.S. economy. In addition, NORA’s seven cross-sectors will continue to focus on the major health and safety issues affecting the U.S. working population. While NIOSH serves as the steward to move this effort forward, it is truly a national effort. NORA is carried out through councils comprised of members with many diverse interests that are developing and implementing research agendas for the occupational safety and health community over the third decade (2016-2026) of NORA. Councils address objectives through information exchange, partnership building, and enhanced dissemination and implementation of evidenced-based solutions. NORA groups industries into 10 sectors using North American Industry Classification System (NAICS) codes. The Mining Sector encompasses NAICS code grouping 21xxxx where “xxxx” represents the different subcodes of the mining “21” classification. Mining encompasses the extraction of solid mineral and mineral-like substances from their place in the Earth’s crust and supplies them to processing industries that produce economically valuable materials. It does not include oil and gas extraction. The Mine Safety and Health Administration, MSHA separates mining into coal, underground and surface, and metal and nonmetal, underground and surface.

Feb 1, 2024

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

DESCRIPTION OF OREThe ore consists, in general, of a very finely grained mixture of sphalerite, galena, and pyrite, with a gangue of quartz and schistose material, and contains about one ounce of silver to the unit of lead.Minor minerals are chalcopyrite, tetrahedrite, and ruby silver. The amount of gangue within the ore-bodies themselves is usually less than 20% of the weight of the whole. The ore is banded in a way that corresponds to the structure of the original schists, and is by no means uniform in composition-at one point, for example, blende may predominate, and a few feet farther on the body may become highly pyritic.Owing to the intimate association of the mineral constituents of the ore, it is very difficult to separate them from one another.Although this remark applies to ore from all parts of the field, the difficulty is particularly noticeable with Rosebery ore, the minerals of which are more intimately mixed, and are of smaller grain size than are the minerals of the Hercules ore.To effect a reasonably clean separation, it is necessary to grind the ore so that 90% passes a 200-mesh I.M.M. screen. Microscopic examination of the crushed product shows that 85% of the minus 200-mesh material is less than 30 microns in diameter, or, in terms of screen sizing, is minus 400 mesh. Particles under 30 microns are found to consist, of one mineral only, but in particles over this size separation has not always been effected. For instance, it is known that part of the galena and of the pyrite in the zinc concentrate is associated with sphalerite, and that part of the galena in the mill residue is associated with pyrite. There is only slight association between the minerals in the lead concentrate.

Jan 1, 1927

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

Caterpillar’s 797 327-t (360-st) mining truck is currently being tested at the company’s proving facilities. Mine evaluations began in the second quarter. The unit will be commerically available in North America in 2000 and worldwide in 2001. The new model is the largest of Caterpillar’s off high-way truck line. In addition, the company has replaced its 966F series II and 970 F wheel loaders with the966G and 972G models. 797 mining haul truck Caterpillar developed the 797 mining haul truck in response to mining companies seeking to reduce cost per ton in large-scale operations. The 797 is sized to work with loading shovels used in large mining operations. And Caterpillar will match the body design to the material being hauled, to optimize pay-loads.

Jan 1, 1999