Search Documents

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By D. Harrington

During the 5-year period 1906-10 inclusive, 84 major disasters (a major disaster being one in which 5 or more lives are lost) occurred in the coal mines of the United States, or an average of 17 per year, and the total number of fatalities from coal-mine gas and dust explosions (major plus minor) for the 5 years aggregated 2,338 or 477.6 per year. The monotonous continuance of coal-mine disasters month by month aroused the people of the United States to such an extent that it was felt necessary for the Federal Government to try to do something looking to the avoidance of the admittedly excessive loss of life in our coal mines, and this was one of the deciding factors in the establishment of the United States Bureau of Mires in 1910. That results have been obtained in this particular cause of coal-mine accidents may be seen from the fact that for the year 1933 but one major explosion disaster occurred in the coal mines of then united States and the total number killed in that disaster was 7. Unquestionably the coal-mining industry through use of oaf or mining practices and aided by the various kinds of work of the Bureau of Mines looking to the prevention of mine fires and explosions is in large part responsible for this very creditable change. If the gas and dust explosion fatality rate of 1.059 per million tons of coal produced during the period 1906-10 inclusive had continued to the first of January 1934, instead of the 6,373 deaths which actually occurred due to gas and dust explosions, there would have been 13,480. Hence, during the 23 years existence of the Bureau of Mines there has apparently been a saving of about 7,102 probable deaths, or an average of more than 300 per year, from gas and dust explosions as against the number which would have occurred had the 1.059 gas and dust explosion fatality rate for the period 1906-10 continued. Thirty-nine persons were killed in all kinds of explosions (both major and minor) in the coal mines of the United States in 1933; if the 1.059 gas and dust fatality rate of the 1900-10 period had been in effect in 1933, about 400 persons world have been killed. Unquestionably, the various teachings of the U.S. Bureau of Mines looking to the avoidance of explosions and fires in mines have had a vital influence in reducing the number of explosions and fires and also in decreasing their destruction in case they occur.

Jan 1, 1934

By Ian MacKenzie

Over the past twelve years, professionals such as architects, engineers, accountants, and attorneys have not had to pay a great deal of attention to GST. The fees charged to clients (outputs) have not been subject to GST, but they have had to pay GST on al purchases of materials and taxable services relating to their activities.

Jan 1, 1990

By Armando Gallegos Monteagudo

El presente texto señala las experiencias realizadas en GERENS, empresa de consultoría y capacitación en gestión del sector minero, formulación, implementación y control de planes estratégicos que utiliza herramientas con un alto nivel ambiental en la creación de valor económica, ambiental para las empresas mineras el Balanced Scorecard (BSC) y el análisis de la cadena de valor de la empresa. El Balanced Scorecard es una herramienta gerencial que apoya la implementación del plan estratégico y permite su monitoreo y control. Para ello, el BSC requiere que el plan estratégico de la empresa se traduzca en objetivos claros y medibles, indicadores, líneas de base, metas, y programas de acción estratégicos y tácticos.

Sep 12, 2005

By Horace C. Porter, F. K. OVITZ

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantitieS', a series . of tests was begun in the fall of 1909 under the supervision of tT. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for exaIp.ple, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New R~ver (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a fu11 account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included. The tests of New River coal, in cooperation with the Navy Department, were undertaken to determine the advantage to be gained by storing coal under water, and particularly under salt water. Small lots were used in order to make the tests of maximum severity, and parallel experiments were made with run-of-mine and crushed coal under one-fourth inch size. All of the small lots tested under the different conditions (except those tested near Key West, Fla.) were taken as representative portions from one large original lot. The tests of Pocahontas coal, which, like the New River, is semibituminous, were undertaken chiefly to determine th.e effect of the tropical conditions in Panama. They were made on an outdoor pile of 100 tons of run-of-mine coal. Pittsburgh gas coal, a high-volatile, bituminous type used at gas and by-product coke works, was exposed for test at Ann Arbor, Mich., in cooperation with the University of Michigan. The university agreed to make tests at successive intervals of storage to determine, in its illuminating-gas experiment station, the yields of gas and byproducts from the coal. The coal, screened lump, was stored in about 4-ton lots out of doors in open bins. Subbituminous coal, which is mined in Colorado, Wyoming, and other States, and is known also as "black lignite," is commonly supposed to deteriorate rapidly in storage, especially by "slacking" or crumbling of the lumps. The tests herein described were undertaken at Sheridan, Wyo., in cooperation with the Chicago, Burlington & Quincy Railroad Co., in order to determine the extent of this slacking and the accompanying loss of heat value. The tests were in open bins holding 4 to 12 tons.

Jan 1, 1917

1. Domestic Production and Use: In 1982, 13 companies operated 30 primary aluminum reduction plants, with 3 firms accounting for 55% of production. Washington, Oregon, and Montana accounted for 34% of the production; Texas, Louisiana, Missouri, and Arkansas 18%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central and eastern States 34%. Based on published producer prices, output of primary metal in 1982 was valued at over $5.5 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 39% of domestic consumption in 1982, transportation 20%, building 14%, electrical 8%, consumer durables 8%, and other uses 11%.

Jan 1, 1983

By Anthony Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. In this sense, the paper point out the GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. GIS’s proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Aug 25, 2002

By J. M. Cummings

CONSIPERABLE information on the industrial or non-metallic mineral resources of British Columbia has been published. For a general resume of the subject, reference may be made to a paper presented by A. M. Richmond before the Annual General Meeting of the Institute in 1935 (1). To avoid duplication, the present paper is confined to a discussion of the existing industrial mineral industry of the Province and of the factors governing its present and future development. British Columbia's mineral production in 1936 had a value approximately 15 per cent of that for the whole of Canada. Preliminary estimates for 1937 indicate that this proportion has been maintained, although the totals have increased about 25 per cent. The following table presents comparative figures, for the year 1936, illustrating the relative importance of the major divisions of the mineral industry in British Columbia and in Canada as a whole.

Jan 1, 1938

Implementation of an Energy Efficient Dry Grinding Technology into an Anglo-American Zinc Beneficiation Process

Sep 13, 2010

By Eduardo Macedo Junior

O presente trabalho descreve o desenvolvimento de uma nova especificação para a Linha de zincagem numero 3 (LZC#3) da Companhia siderúrgica nacional (CSN), de grande demanda e aceitação, alta produtividade e foco nos requisitos do cliente que tangem qualidade superficial e características metalúrgicas (resistência mecânica) em aços para atendimento do mercado Norte-americano. Este novo produto tem como característica o ciclo de recozimento com velocidade alta para obtenção de microestrutura 100% encruada na saída do equipamento e limites de escoamento e resistência acima de 500 MPa. A combinação dessas características do produto junto com as características do processo tornou a especificação “ASTM-A653MSS80CL1” um grande desafio para garantir qualidade superficial sem comprometer as propriedades mecânicas especificadas assim como a integridade do equipamento. O baixo custo de produção associado a alta produtividade desse produto fazem da especificação “ASTM-A653M-SS80CL1” um produto de extrema importância para a estratégia adotada pela CSN, mantendo dessa maneira sua competitividade no mercado Norte-americano e garantindo capacidade máxima de produção do seu equipamento em tempos de retração do mercado interno.

Aug 17, 2017

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By H. Sevim

Mining engineering curriculum has been discussed and debated in meetings and conferences, and opinions and recommendations have been published in the literature since the inception of the official degree-granting mining engineering program at the Columbia School of Mines in 1864. The deliberations have usually been heightened during the periods of boom-and-bust cycles experienced by the mining industry since the 1920s. Currently, the global natural resource industry is undergoing another cycle, called ?super cycle,? characterized by elevated prices for metals and other natural resources. The super cycle is occurring as a result of the large deficit between the global supply and demand for natural resources, due, in large part, to economic expansion and development in countries such as China, India and Brazil. Because of this cycle, there is a shortage of mining engineers in the U.S., Canada and Australia.

Jan 1, 2012

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis' in graphical form. In 1953 Fatt' also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie' equation, and the more general Winsauer equation', where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By R. S. Dean

This report, the third of a series of annual reports of the Metallurgical Division to be released in this form, covers the fiscal year July 1, 1936, to June 30, 1937. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By Raymond M. Howe

Additional data have been secured on the disintegration of furnace linings and the spalling of stove brick. The first article on the disintegration of furnace linings appears to have been written by John Pattinson in 1876.l The furnace involved was 85 ft. (25.0 m.) higher and 27 ft. (8.2 m.) in diameter at the boshes; after being in blast five years, the top brick became contaminated with carbon and disintegrated. An examination of the lining showed that the discolored, disintegrated brick were in a zone found from 35 to 67 ft. (10.6 to 20.4 m.) above the hearth; immediately below, in a zone extending from 22 to 40 ft. (6.7 to 12.1 m.) above the hearth, the brick were hard and porcelain-like in appearance. Analyses of samples taken from the different sections are given in Table I. The water-soluble portion found in the sample taken 39 ft. (11.8 m.) above the hearth had a composition approximately as follows: silica, 0.50 per cent.; lime, 0.04 per cent.; potash, 0.78 per cent.; soda, 0.20 per cent.; potassium chloride, 6.19 per cent.; moisture, 1.03 per cent.; total, 8.74 per cent. The carbon Table 1.—-Analyses of Samples Taken from Diferent Sections of Furnace . I ii In Iv v Section 67 Section 45 Seotion 39 Section of Original ft Above ft above ft above vitrified Lining Hearth Hearth Hearth Portion Per Cent. per Cent per Cent per cent. per Cent Silica........................... 55.70 55.60 55.67 47.60 37.07, Alumina........................ 35.50 35.40 30.00 26.47 23.18 Ferric oxide..................... 3.00 1.32 0.96 Lime........................... 0.23 0.06 0.17 Magnesia....................... 1.22 0.95 0.86 0.00 Potash......................... 2.60 2.10 5.30 7.54 21.59 Soda.........,.................. 0.45 0.42 1.67 0-76 6.28 Ca1bon ......................... 2.05 3.24 5.97 Carbon dioxide.................................. 2.. 17 Water...................................... 7.70 Water-soluble........................... 8.74

Jan 1, 1920

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By F. Sorensen

ABSTRACT Electricity production by the Electricity Supply Commission of South Africa (Eskom) is the most important beneficiation process for South African coal. As one of the world’s lowest cost producers, energy-intensive industries such as ferroalloys and aluminium were introduced. However the poor were neglected. The white paper on energy policy (Department of Minerals and Energy, 1998) sought to redress this. Also, chasing economic growth to generate jobs resulted in high electricity demand and interruptions. Lifespan estimates of South African coal reserves based upon peak theory vary widely. Approaching peak, coal production in the future will be more expensive and, thus, contribute to more expensive electricity, which could inhibit industrial development unless South Africans work smarter.

Jan 1, 2011