Search Documents

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By Thais Cristina da Costa Caldas, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has as its objective to evaluate the firing behavior of a kaolinitic clayey body from Campos dos Goytacazes-RJ incorporated with flat glass waste (FGW) from civil construction. Incorporations of the waste, with a particle size less than 74 µm (200 mesh), were performed in the red ceramic in the following amounts: 0, 2.5, 5 and 10 wt%. Specimens were prepared by uniaxial press-molding and then fired at 850 and 1050°C. The characterization of FGW was done by X-ray Fluorescence. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy (OM). The obtained results showed that the flat glass waste can be used as a component of ceramic bodies once it was noticed tolerable modifications of technological behavior.IntroductionBrazil is one of the world’s largest producers and consumers of clayey ceramic. Campos dos Goytacazes is located in the north of the State of Rio de Janeiro, southeast of Brazil, it’s known as a large producer of red ceramics. It is estimated that the production of bricks can reach 1 billion pieces per year [1].Nowadays, recycling processes became more and more important, due the generation of wastes in large scale and the preoccupation with environmental. The amount of glass waste has been exponentially growing with the growth of the population. It is estimated that the amount of discarded glass as bottles, construction windows, packing and other glass waste represented in 2006 an amount of 7.5% of the total weight of the world´s domestic garbage [2]."

Jan 1, 2012

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By G. D. Sandrock

The science and technology of roan temperature rechargeable metal hydrides began about 1969 with the discoveries that the intermetallic Compounds LaNi5 and TiFe could be, conveniently hydrided and dehydrided at roan temperature and modest H2 pressures. Subsequently, this lead to the development of a broad family of REE-containing AB5 hydrides and numerous applications that make use of the extraordinary H2-absorption and reaction-heat properties of these materials. Some of the applications include H2 storage, compression and separation, as well as heat pumping, heat to mechanical energy conversion and electric energy storage. This paper briefly reviews the fundamental phenomenology of metal hydrides, the history of the use of REE's in rechargeable metal hydrides, the practical engineering properties of these materials and the applications that have evolved around them. The rechargeable nickel metal hydride battery, a new vial alternative to NiCd cells, stands at the forefront of the applications.

Jan 1, 1992

By Guozhu Ye, Mikael Lindvall

"Swedish iron ore contains about 0.1 %V. The vanadium is reduced to the hot metal in a blast furnace and oxidised to the slag in a converter. The high V-content, up to 5 % V, leads to a very limited external application of the steel slag in Sweden. Since 2004, MISTRA - the Swedish Foundation for Strategic Environmental Research has together with the steel and mining industry in Sweden and Finland initiated and supported a long term project aiming at efficient recovery of vanadium in the slag, and at the same time a useful slag product with low V-content. The proposed concept consists of a reduction step and a phosphorus removal step. This paper will highlight some of the results with focus on the various metallurgical reactors used for slag reduction, including results from recently performed pilot trials using a DC furnace for cotreatment of metallurgical slags and other wastes.IntroductionToday, less than half of the produced LD-slag in Sweden is recycled to the blast furnace as a lime source and the rest is temporarily stored inside the steel plant. The steel slags cannot be used externally due to its content of vanadium and free lime. As the slag storage area is limited, this has become a problem for Swedish steel producers. The disposition of the slag is also a great waste of a valuable vanadium resource. The current potential value of vanadium in the discharged steel slag annually amounts to roughly US$ 100 million. Currently, Swerea MEFOS is conducting an 8-year vanadium recovery project called VILD (Vanadium in LD-slag) aiming at efficient recovery of vanadium and at the same time producing a useful slag product with low V-content. The project is financed by MISTRA - the Swedish Foundation for Strategic Environmental Research and the steel and mining industry in Sweden and Finland. Various reactors and process options have been tested in the past 7 years, from 3 kg laboratory scale, 150 kg induction furnace, 3 MVA pilot DC furnace, 5 MVA pilot AC furnace, 5 tons Kaldo furnace, to full scale direct hot slag reduction in the industrial site (12 tons of slag). This paper will introduce the VILD-concept and review the experiences gained from these trials. The advantages and disadvantages of the different options will be discussed and concluded."

Jan 1, 2012

By John W. Graydon

Incineration is an attractive alternative to the disposal of MSW in landfill sites. However, the process of incineration generates fly ash which contains significant levels of leachable heavy metals - particularly cadmium, lead, and zinc - and it is essential to manage this fly ash in an environmentally sound manner. The compositions, phases, textures, morphologies and size of fly ash particles have been studied by light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how fly ash is formed during incineration, in understanding the leaching behavior of untreated fly ash if it is disposed of in a landfill and, most importantly, in guiding the development of the best treatment strategies for fly asti to mitigate its environmental impact.

Jan 1, 1992

By Hsing Kuang Lin

Ferric chloride leaching w.as applied to a complex sulfide ore from Tok, Alaska to dissolve zinc, lead, silver and copper. Gold in the leaching residue, as well as in the ore, is found to be refractory to the conventional cyanidation process. Roasting, pressure oxidation and elemental sulfur removal followed by cyanidation were tested to improve gold dissolution. Also tested were thiourea leaching and high-pressure cyanidation. The readsorption of dissolved gold by carbonaceous matter in the chloride leaching residue was analyzed. Based on the experimental results, factors causing difficulty of gold dissolution from the leaching residue are discussed.

Jan 1, 1989

By Zhiqiang Zhou, Libin Zhu, Zizong Zhu, Hao Xiong, Yuchuan Ding

In order to utilize the lean ore resources from XinJiang rationally and optimize mixture, laborarory measurements have been carried out under different basicity, various mixed carbon content as well as the properties (ratio) of fuel particle size by the sintering pot for further microstructure analyses. The results show that sinter strength falls by 5.0%, low temperature reduction disintegration index (RDI) drops off to the lowest in certain ranges. The natural degradation index of sinter is much higher when sinter basicity is between 1.65 and 1.75. The sinter strength increases when sinter basicity is between 1.75 and 2.0. Meanwhile, the sinter strength and RDI +3.15 improve with increasing carbon content. And the sinter strength and RDI+3.15 both decrease with the decrease of the distribution ratio of small fuel particle, thereby decreases the yield of sinter. Microstructural analyses have been investigated to figure out the mechanism of the influence of the three factors on sinter.

Mar 1, 2017

By B. Mishra

Several reactive metal purification processes using molten salts generate effluent from which significant quantities of metal can be recovered prior to discardinglrecycling the salt. A Salt-scrub [SS] process has been applied where the reactive metals are recovered as a metal-gallium alloy by calciothermic reduction of the metal compounds. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. Measurement of metal recovery has been studied for cerium, silver, tin and lead. The process has been optimized for variables such as the metal quantity per kg of effluent salt, amount of excess calcium over stoichiometry, stirring rate and time and holding time at reduction temperature. Over ninety-seven percent metal recovery has been obtained under optimized conditions. The development of an alloy for efficient Salt Scrub processing reduces a major contaminated waste disposal problem as well as recovering the valuable reactive metal. Surrogate metals have been used in this work to study the behavior of plutonium.

Jan 1, 1994

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

By Jian-guang Yang, Lei Jie, Si-yao Peng, Jian-ying Yang

A new membrane electrolysis process for bismuth recovery from bismuthinite concentrate was introduced. Under the conditions of temperature 70 degrees C, acidity 3 mol/L, solid liquid ratio 1:4 and 1.1 times stoichiometry sodium chlorate dosage for 1.5 h oxidation leaching, more than 98.5% bismuth can be leached from bismuthinite concentrate. The resultant leach solution was subjected to membrane electrolysis. Under the conditions of NaCl concentration 300 g/L and pH 7 in anolyte, bismuth ions concentration 80 g/L and HCl concentration 3 mol/L in catholyte, heteropole distance 6 cm, temperature 40 degrees C and current density 200 A/m2, a flat deposited bismuth plate can be obtained after 24 h electrolysis, and the bismuth purity was more than 99%. The current efficiency of cathode was 97.88%. Chemical component analysis results showed that the average convert efficiency of the sodium chlorate was 52.77% and the average oxidizing efficiency of chloride ion was 69.78%, and the resultant anolyte generated in anode compartment could be fully reused as oxidant for leaching bismuthinite concentrate again.

Mar 1, 2017

By D. M. Wyslouzil

The fundamentals of dissolving silver and silver minerals are discussed in the following sections: 1) Basic chemical reactions in the silver system 2) Leaching of pure silver minerals 3) Leaching of silver-bearing ores 4) Description of processes The basic chemical reactions of silver are an important guide to the mineral processor or the extractive metallurgist, particularly for systems in which complex formations are balanced against solubilities. The competition of other cations for free ligands can shift the equilibrium to the detriment of silver. Solubilities of pure silver minerals in specific solvents may not be a good indication of the solubility of silver minerals in ores. The abundance of silver minerals which usually appear in a typical ore precludes the selection of a single method that would result in the best extraction of silver from all minerals in the ore. Frequently, the recovery of silver from host minerals requires a destructive pretreatment such as intensive leaching, oxidation with or without elevated temperature and oxygen pressure, or roasting. The transformation of the host or the silver minerals does not always result in a leachable species? and this requires additional treatment before the precious metal can be recovered.

Jan 1, 1990

By Daniel Hoffman, Katerina Aifantis, Ibrahim Miskioglu, Jaroslaw Drelich

"A new method to determine the elastic modulus of a material using the atomic force microscope (AFM) has been proposed by Tang et al. (Nanotechnology 2008, 19, 495713). This method models the cantilever and the sample as two springs in a series. The ratio of the cantilever spring constant (k) to diameter of the tip (2a) is treated in the model as one parameter (a=k/2a). The value of a, along with the cantilever sensitivity, are determined on two reference samples with known mechanical properties and then used to find the elastic modulus of an unknown sample. To determine the reliability and accuracy of this technique it was tested on several polymers. Traditional depth-sensing nanoindentation was preformed for comparison. Using both methods, the elastic modulus of the polymers tested was calculated. The elastic modulus values from the AFM were within ±(5-20)% of the nanoindenter results.IntroductionThe atomic force microscope (AFM) has proven to be a useful tool for characterizing materials on the micro- to nano-scale. The most common use of AFM is to image and measure the topography of the sample surface, but AFM has also been used to characterize the mechanical properties of materials [1-3]. With AFM's ability to scan the sample surface, features of interest can be found and indented. It provides an advantage over traditional nanoindenters that use optical microscopes and thus cannot resolve nano-scale features. This makes AFM a useful tool for characterizing materials on the nano-scale."

Jan 1, 2011

By Huimin Lu, Neale R. Neelameggham, Guangzhi Wu

In China’s Inner Mongolia Tuquan County, 1.4 billion tons of reserves of serpentine deposits were found. Because serpentine belongs to magnesium silicate, there is no good reducing agent to reduce magnesium. In the local there is also a large reserves of high-aluminum bituminous coal for thermal power, power plants each year produce a large number of high-aluminum fly ash. The aluminum-silicon alloys obtained from this high-aluminum fly ash as the raw material by carbothermal reduction method can reduce the magnesium from the serpentine. In this paper, first, the feasibility of producing aluminum-silicon alloys by carbothermal reduction of high-alumina fly ash was studied, the hypereutectic aluminum-silicon alloys were obtained; and then the investigation on aluminum-silicon alloy as a reducing agent to reduce of metal magnesium from serpentine was carried out. According to the previous investigation, the optimized technical process for the extraction of metal magnesium from serpentine was proposed.

Mar 1, 2018

By George J. Karcas

"Non-ferrous metals such as copper, nickel, lead, zinc and precious metals are produced via the electrorefining and electrowinning processes. Apart from controlling electro-chemical conditions for the production of these metals, there has always existed the challenge of controlling the corrosive effect of the electrolyte environment which serves as the medium for non-ferrous metal production.The practice of acid containment in electrometallurgical operations has entered the world of high technology with the advent of advanced acid resistant materials such as vinyl ester resin which is either combined with aggregate to form polymer concrete or used to line various acid containment vessels and ·surfaces. ill comparison to some Asian, European, and African copper refineries, the North and South American copper industry has recently embraced quite heavily in the use of polymer concrete electrolytic cells and process vessels, such as electrolyte storage tanks, and in the use of vinyl ester resin for corrosion protective surface sealing 'systems in lieu of epoxy, acrylic and other materials because of its combination of higher corrosion resistance and superior flexibility.Electrolytic cell construction has undergone a transformation from a multiple part configuration to a single piece moulded/cast unit. ·The one piece moulded polymer concrete cell, which has been patented by Corrosion Technology International, with the overflow, decant, inlet, fast fill and segregation systems integrally designed is now the industry standard.. The combination of a wood, steel, or concrete frame with a lining made of lead, asphalt, rubber or plastic has been historically successful in providing limited protection from chemical and mechanical attack in electrolytic cells and electrolyte storage tanks all over the world. These combinations have now become obsolete as materials such as polymer concrete provide exceptional corrosion and mechanical protection with greatly reduced maintenance requirements and improved efficiency and productivity for the tankhouse. ill addition, polymer concrete can be disposed of in a regular land fIll which is much less costly than disposing of contaminated concrete that is normally associated with conventional lined concrete cells."

Jan 1, 1997

By Zhang Hanbo, Niu Liping, Zhang Zhiqi, He Jicheng, Dou Zhihe

"Rutile, ilmenite and Al-Ca complex reducer were used to prepare high titanium ferrous alloy by enhanced reduction-SHS method. The effects of the complex reducer compositions and slag types on the enhanced reduction-SHS process were investigated. The high titanium ferrous alloys were characterized by XRD and SEM. The results indicate that the high titanium ferrous alloys consist mainly of TiFe2, AlTi3 and Al2O3. The oxide inclusions exist resulting in directly the high oxygen content and micro-structural defects in the alloys. The titanium and oxygen contents decrease, but the aluminum content in the alloy increases while the mass ratio of calcium in the Al-Ca complex reducers increases. When the mass ratio of Al/Ca in the Al-Ca complex reducer is 6:1, titanium, oxygen and aluminum contents are 63.75%, 3.01% and 10.72% respectively. When the mass ratio of Al/Ca is 5:1 titanium content is 55.00% nearly and aluminum content is higher than 14.00%, but oxygen content is lower than 2.0%.1. IntroductionThe high titanium ferroalloys with 65%~75% titanium have the advantages of low melting point and high titanium content. They are widely used in special steel refining, while they are also a kind of very important quality orientation alloys in the rage of aviation and aerospace. At present, the methods of preparing high titanium ferroalloy include vacuum remelting and thermit reduction. The alloys prepared by the vacuum remelting method have good qualities and low oxygen content, so it is widely used in Russia, Western Europe and other developed countries. In China, there are abundant rutile resources, but waste titanium is lack, therefore, the preparation method is the thermit reduction. But there are many quality defects in the high ferrotitanium alloy, including high oxygen content, unstable quality and so on. In order to improve the qualities of the high titanium ferroalloy, especially to reduce oxygen content, the domestic and overseas have done a lot of further researches. For example, Sichuan E-mei ferroalloy plant and Beijing Nonferrous Metal Research Institute have prepared high titanium ferrous with 73.77% titanium with natural rutile, but the oxygen content is high. Through controlling the quality of raw material, they obtained the better qualities, but the oxygen content is still very high. South Africa Mintek company have prepared high titanium ferrous alloy with low nitrate by plasma heating under the isolation air conditions, but they couldn’t also remove effectively oxygen in the alloy. The oxygen exists in the form of Al2O3 and titanium protoxide. So it can be speculated that except TiO2 not being fully reduced, the no-sufficient alloy-slag separation is the direct reason resulting in high oxygen and poor microstructure. In view of present technical difficulties during preparing high titanium ferroalloy by thermit reduction, this paper proposed a new method of preparing high titanium ferrous with low oxygen by enhanced reduction-SHS with Al-Ca complex reducer. Ca in Al-Ca complex reducer has stronger reductive ability, it can effectively strengthen the reductive degree of TiO2. The slagging agent CaO CaF2 and MgO can effectively reduce the viscosity of Al2O3 slag to improve its liquidities to strengthen alloy-slag separation effects so that to remove inclusions and oxygen. In this paper, effects of slagging agent type on the reduction and the qualities of high-titanium ferroalloy were studied."

Jan 1, 2012

By Shengli Wu, Yuandong Pei, Zhixing Zhao, Shuhai Ou, Jiangshan Shi, Huaiying Ma, Jun Xiong

Spraying technology on sintering surface bed after ignition has become a hot research topic, with the purpose of achieving energy-saving, emission reduction and improvement of sintering indexes. In this paper spraying steam technology was researched from theory, experiment and practice. First of all, from the thermody- namic and kinetic analysis, the mechanism of sintering surface spraying steam was analyzed and its advantageous effect was con firmed. Based on this, sintering pot test and commercial trial were carried out respectively. The results shown that spraying steam is bene ficial for increasing coke combustion ef ficiency with improving CO 2/(CO+CO2) in the exhaust gas from 80% to about 85% level, through decreasing CO content of flue gas by more than 1000 –2000 ppm. There was a suitable spraying amount to improve the quality of the sinter, and the spraying position of the steam cannot be excessively front and rear. Due to the low steam pressure (1 kg) and temperature (about 100 °C) compared with industrial steam (3 kg and 130 °C, respectively), the sinter quality such as yield index was affected by spraying steam in sintering pot test to a certain extent, and proper spraying amount (0.008 m 3, 50 kg sinter) in sinter pot test is far smaller than application amount in commercial trial (2t/h). It is thought that suitable spraying steam parameters has a comprehensive effect of energy saving and quality improvement.

Mar 1, 2018

By Tom W. Gonzales

Magma Metals Company commissioned a 3000 tpd Outokumpu flash smelting furnace in July 1988. Through September 1992 the PSP has smelted a first campaign record 4.1 million tons of concentrate. This paper discusses modifications made to the original process equipment to overcome design flaws as well as future design changes currently under consideration.

Jan 1, 1993

By M. Oliazadeh

Spodumene [LiAl(Si2O6)] is the most common and desirable economic lithium-bearing mineral due to its high lithium content. In Canada, there are several spodumene deposits at the development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and increasing use of electric vehicles. Spodumene processing can be conducted using Dense Media Separation (DMS), flotation or combination of both. If spodumene liberation is sufficient at coarse particle sizes, DMS can be used for primary lithium concentrate production and silicate gangue minerals rejection. If liberation is not sufficient, flotation is then the main processing route for spodumene concentration. Even in cases where DMS is a viable beneficiation option, flotation may still be required to process the DMS middlings and/or the undersize fraction which is outside the particle size range for DMS. Considering flotation as a technique for spodumene beneficiation, there are several alternatives including the use of mechanical flotation cells, column flotation cells, coarse particle flotation cells, and/or Staged Flotation Reactors (SFR), either alone or in combination. Ore sorting can be incorporated at the start of the spodumene flowsheet to remove gangue minerals, particularly amphibole and pyroxene in the early stages. The main objective of flowsheet development for hard rock lithium deposits is to evaluate the ability of these options to produce a spodumene concentrate with a concentrate grade above 6% Li2O, lithium recovery of above 80%, and with the minimum operating and capital cost. This paper aims to describe the various processing options available for the beneficiation of spodumene from hard rock deposits and compare the associated operating and capital costs for each.

By Zhang-Guang Gao, Ming-Mei Zhu, Rui-Rui Zhao, Chao Jiang

This paper focuses on the CaO-SiO2-FeO-MgO-MnO-P2O5 slag system that represents the major components of dephosphorization slag in BOF. Phosphorus distribution between 2CaOSiO2-3CaOP2O5 Solid Solution and Liquid Slag were analyzed by FactSage. The effects of slag content, basicity on the distribution ratio of P between the solid solution phase and the liquid phase (LP) and the percentage content of P in solid solution phase and liquid phase have been discussed. The results show that, with the increase of basicity, LP (wt%) decreases until the basicity reaches 1.9, then it turns to increase. LP (wt%) increases gradually with the increasing amount of FeO or P2O5.

Mar 1, 2017