Search Documents

By George Kachaniwsky

Until mid-1982 the Mines Gaspe copper smelter consisted of a fluid bed roaster, a reverberatory furnace, two Peirce-Smith converters of which only one was blowing at any one time, anode casting facilities, and a single contact sulphuric acid plant treating both roaster and converter gases. Reduced concentrate supplies have led to the shutdown of the roaster and, as a result, it was necessary to adapt the converter and acid plant operation to the new operating mode: green concentrate smelting with resulting lower matte grades and acid plant treatment of off-gases from only one blowing converter. Therefore, modifications were carried out to existing equipment and methods of operation and control. This paper describes the result of work done to obtain steady, maximum strength, converter off-gas flow and an efficient acid plant operation. Topics covered include: optimization of converter operation, tightness of hood and off-gas ducting, improvements in acid plant/converter communications and modifications of acid plant operation and control to cope with the fluctuations in converter gas flowrates and strengths.

Jan 1, 1983

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

The generation of acid mine water is? due to the oxidation and weathering of sulfide bearing tailings and overburdens. Ferrite precipitation prooess has been applied to treat acid mine water. The conventional ferrite preC1pitatlon requires air oxidation at high temperature, or long aging time or addition of magnetite powder ,as promoter. In this investigation, a modified ferrite, precipitation process is developed by which magnetic ferrite can be produced at an ambient temperature. Acid mine waters from Berkeley Pit (Montana, U. S. A.) and from Noranda Tailings (Quebec, Canada) were used. The co precipitation of heavy metals from these two acid mine waters is studied as a function of FeIM molar ratio, oxidation time and settling rate under applied magnetic field. The investigation indicates that the modified ferrite co precipitation can remove substantially all of the, dissolved metal ions from acid mine water. The ferrite product obtained after precipitation' is characterized by XRD, SEM, BET and saturation magnetization. The results show that spinel ferrite, precipitation can be achieved at room temperature and the saturation magnetization of ferrite product from,acid mine water is comparable to that of pure ferrites.

Jan 1, 1995

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 ; R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion. treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By Fernando Castro

Electric furnace steelmaking dust is a polluting residue that needs to be treated in order to recover metals contained and to produce an environmentally acceptable residue. Some hydrometallurgical approaches for its treatment have been evaluated, namely: caustic soda leaching followed by electrolytic recovery of zinc, ammonia leaching followed by zinc compounds precipitation and acetic acid leaching followed by lead, zinc hydroxide and gypsum precipitation.

Jan 1, 1992

By Carl C. Nesbitt

A study was conducted to investigate the claims of early observers who noted an increase in the rate of gold dissolution when chlorine was chemically produced in the leach vessel compared to sparging with chlorine gas. This "nascent" chlorine was presumed to be an active intermediate in the production of chlorine (C1,l from chloride ions. The study used UV light to produce an activated chlorine atom intended to recreate the observed increase in the gold dissolution rate. Although no change in the kinetic rate was observed, the reaction mechanism by which chlorine reacts with particulate gold was instead determined. Various concentrations of multivalent cationic chloride salts were added to the leach solution to demonstrate that the increased dissolution rate was due to the increased concentration of the chloride ion and ionic strength of the solution.

Jan 1, 1992

By Yasuyuki Murayama

MF is the semi-blast furnace which has been developed at Mitsui Miike Smelter in the 1960's to treat vertical retort residue. The MF has also been tested for treatment of various recycling materials and wastes. Now various secondaries and wastes (steel dust, zinc leaching residue, Cu-Ag sludge, spent catalyst and spent rubber, etc.) are mainly treated. Powder materials are briquetted with reductant before being fed to the furnace. Products are crude zinc oxide, matte, non-hazardous slag and steam. Zinc and lead are recovered in oxide dust, and copper and silver are recovered in the matte. The MF furnace can be widely applied to many kinds of materials which contain such non-ferrous metal-valuables. In addition, the improvement in operation and technology has effectively made the unit capacity much larger. The MF furnace now has many advantages for these treatment processes.

Jan 1, 1992

By Elders. Wilfred A.

Petrological and geochemical methods, the utility of which has long been established in the mining industry, are proving useful and cost-effective in elucidating the thermal evolution of active geothermal fields. In return, they yield insights into sulfide-silicate equilibria, mass and energy transfer in convecting hydrothermal systems, and the genesis of hydrothermal ore bodies. Within the Plio-Pleistocene sediments of the delta of the Colorado River, in the Salton Trough, several active geothermal systems are known. Temperatures vary from 100-365°C, at less than 2 km depth, and salinities vary from 3,000 to 280,000 ppm, total dissolved solids. The hydrothermal alteration causes marked induration of the sediments, producing greenschist facies metamorphic minerals, including hydrothermal ore minerals. Subsurface authigenic minerals show strong correlation with increasing temperature. A typical sequence in sandstones is (below 150°=C) montmoril-lonite-kaolinite, (above 180°C) chlorite + illite, (above 225°C) calc-alumino-silicates, (above 325°C) biotite. There is a transition from porosity-dominated\to fracture-dominated permeability in the hottest and deepest geothermal reservoirs. This regular series of minerals provides a practical tool during exploration drilling. From drill cuttings, we can make predictions on reservoir temperatures, useful in making decisions on well completion. Other types of geothermometry we have employed include light stable isotopes, fluid inclusions and vitrinite reflectance measurements. A combination of these techniques not only improves our temperature predictions, but together with fission tack annealing studies, permits us to model the dynamics of temperature change and fluid flow in these geothermal reservoirs.

Jan 1, 1981

By Volker Uhlenwinkel

The design of a free fall atomizer as well as the process parameters affect the particle mass flux distribution in the spray cone. The mass flux distribution is important in spray forming because of its influence on the deposit shape and enthalpy input into the deposit. In this article the effect of different process parameters on the mass flux distribution is shown. Furthermore, different melts were atomized with the same atomizer. An empirical correlation will be introduced to predict the mass flux in the spray cone. This correlation will be compared with experimental results.

Jan 1, 1999

By W. G. Davenport

This chapter shows how flash furnace industrial oxygen and oil requirements are affected by different: (a) product temperatures (b) conductive, convective and radiative heat losses (c) electrical energy inputs (d) hydrocarbon fuels. The calculations of the chapter are all for production of 65% Cu matte from pure CuFeS2 concentrate. Blast temperature is? 298 K throughout.

Jan 1, 2001

By L. Katgerman, E. N. Straatsma, Suyitno

"Single-roll strip casting process is studied using computational fluid dynamics which takes into account fluid flow, heat transfer and solidification. The computational model is based on the conservation Jaws of momentum, energy and continuity. Correlation of strip thickness, solidification zone length, and puddle shape on single-roll strip casting of Al-1 %Mn is explored. Feeding pressure and roll speed are investigated. The results show that the··strip thickness slightly increases with pressure, similarly the length of solidification zone. The variations of strip thickness and solidification zone length with roll speed show a sharp decline for strip thickness and slight decline for the length of solidification zone with increasing roll speed. The constraint and free-jet flow have different feature in term of flow field. Severe turbulence is observed on the free-jet flow.IntroductionThe near-net shape casting of strip metals is a demand nowadays. The demand is particularly stimulated by the challenge to become more competitive through enhanced performance. The improvement in the existing processes and new innovative technologies are introduced by the metal industry to gain better product quality, more efficiency in energy consumption, low throughput, yield and operating costs [1-3].There are many advantages that can be obtained by the direct casting of strip. The most prominence is the elimination of hot rolling. Beside that the high rate of heat extraction associated with strip casting offers the possibility of a finer, Jess segregated cast structure. The microstructure will result in the improvement of mechanical properties compared to conventional material, or alternatively the opportunity of using grades of metal outside the normal range for continuous casting.The concept of single-roll strip casting has been difficult to commercialize, because of the complex interactions between fluid flow, solidification, shrinkage, and stress, which lead to serious quality problems. Besides that, the quality and the thickness of the strip are affected by the thermal properties of the strip, roll cooling conditions, roll geometry, and other process parameters. To understand how these parameters affect the strip formation, some researchers have modeled the process [4]."

Jan 1, 2004

By Merete Tangstad, Lars Klemet Jakobsson

"Slag refining is a promising refining method for boron removal from silicon as a part of a metallurgical route for production of silicon for solar cells. There is, however, limited data on the distribution of impurity elements between silicon and different types of slags. In the present study, the distribution of boron and calcium between silicon and slag were determined at 1600 °C for calcium silicate slags with a CaO/SiC>2 ratio between 0.65 and 1.3. An almost horizontal linear trend was found for the distribution of boron between silicon and slag, and the borate capacity was found to follow the relationln(CB0, ) = 30.8 + 2.96-V (1)where V\s the CaO/SiCh mass ratio within the range of the experiments.IntroductionSolar grade silicon feedstock contributes significantly to the total cost and energy required to make crystalline silicon solar cells. A less expensive and less energy requiring method of solar grade silicon production is therefore needed in order to make crystalline silicon solar cells more viable as an energy source. Silicon is an abundant element and the manufacturing cost of solar grade silicon is therefore mainly determined by costs related to purification of metallurgical grade silicon. The Siemens process is the most common process today, but it is an expensive and highly energy requiring process that gives silicon with a higher purity than is needed for crystalline silicon solar cells. A cheaper and less energy requiring method for production of solar grade silicon can either be achieved by modifying the Siemens process or by using a new production method. Purification of metallurgical grade silicon through a metallurgical route is a promising method that is already in use industrially. It has however proven to be hard to lower the boron content to 0.3 mg/kg or less, which is the requirement for most p-type crystalline silicon solar cell manufacturers. Slag refining is seen as one of the most promising approaches that can be used to bring down the boron content to the required level, but there is not much data on how boron is distributed between silicon and binary calcium silicate slags [1-4]. The distribution of boron between silicon and calcium silicate slags at 1600 °C has been studied in this work, and the obtained data has been used to calculate the borate capacity of binary calcium silicate slags."

Jan 1, 2012

By Jason M. Porter, Douglas L. Porter, David L. Olson, Travis W. Koenig, Van S. Blackwood, Brajendra Mishra, Robert D. Mariani

"Traditional alloy theory models have been applied relative to the three solid phases of uranium: alpha (orthorhombic), beta (tetragonal), and mainly gamma (body centered cubic)[l]. The Darken-Gurry and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer have been used to predict the behavior of four types of solutes: 1) Transition associated with alloying in and containment of the uranium fuel 2) Transuranic elements in the uranium 3) Rare earth fragmentation elements (lanthanides) 4) Transition metals and other fragmentation elements. Using these solute map criteria, elemental behavior have been predicted as highly soluble, marginally soluble, or immiscible (intermetallic phase formers) and have been used to compare solute effects during uranium phase transformations. The overlapping of these solute maps are convenient first approximation tools for predicting alloy behavior.IntroductionAn investigation is in progress to determine the role of various solute elements on size and shape of the 'Y phase field range for uranium to optimize the burning and material processing of nuclear fuel is in progress. Traditional alloy theory models based on correlations to elemental electronic and crystal properties are used to predict solubility and micro structural formation. The effectiveness of this model is based on microstructure property correlations. Darken and Gurry, and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer, models have been used to describe solute solubility with respect to uranium based the on correlation between elemental electronic structure and uranium phases. The alpha (orthorhombic), beta (tetragonal), and gamma (body centered cubic) phases have different solubilities for specific alloy additions as a function of temperature. Using the method of Waber, ellipse diagrams classified those solutes that should have broad solubility in the allotropes of uranium[2]. The predictive diagrams are made from four different correlations:"

Jan 1, 2012

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By F. J. Tavera

Recently Jameson cell technology has gained acceptance in both mineral and non-mineral applications, mainly because of the high degree of contact between the involved phases in the downcomer, fact that leads to an efficient collection performance. The key for an acceptable performance of the downcomer operation depends on the stability of the jet zone, the mixing zone, and the plug flow zone. in this work the behaviour of the downcomer of a laboratory Jameson cell is reported, as a function of gas hold-up, superficial gas velocity, superficial liquid (or slurry) velocity, and length of the operating zones. The presence of carbon is evaluated in terms of its effect on the gas hold-up and bubble surface area flux. The influence of the downcomer operating conditions on the gas-liquid disengaging cell is presented. Keywords: Jameson cell, downcomer, gas hold-up, mixing, plug flow, conductivity.

Jan 1, 2003

By K. Iwami, K. Abe

"Onahama Smelter and Refinery has been operated-since 1965 arid currently produces 243,000 metric tons per year of cathode copper. The Onahama tankhouse consists of conventional-type No.1 and 2 tankhouses with the capacity of 123,000 metric tons per year and No.3 tankhouse with 120,000 metric tons per year, adopting jumbo tank system, using hazelett anode respectively.In October, 1996, for the purpose of improving the - anode verticality, new anode copper body press machine has been installed in No.1, 2 tankhouses; by increasing Walker type anode copper weight by 35kg to 365kg. Consequently, it is possible to raise current density from 191 to 222 A/m2 and the No.1 and 2 tankhouses capacity was increased by 15,000 metric tons per year to 138,000 metric tons per year.At present, the refining capacity is 258,000 metric tons per year in total including No.3 tankhouse.This figure is the largest one in Japan.IntroductionSince the Onaham tankhouse was put into operation in 1965, the cathode copper production has increase with much labor cost saving.The following two cases to increase Walker type anode copper weight by 35kg to 365kg were studied.a) To increase the cathode copper production by raising current density.b) To save the labor cost by prolonging the anode cycle in order to decrease the exchanging time of electrodes.So the electrolytic tests were carried out to confirm· the effect of current efficiency, cathode copper quality and working conditions for space adjustment.As a result, we concluded that it was indispensable to introduce the anode body press machine to keep usual current efficiency and cathode copper quality with same workers, and to be possible to increase cathode copper production.In addition, the high-speed press machine was needed to maintain same working time and which specifications were decided through various investigations. In October 1996, the new anode body press machine made by Kawazoe Machine Works, Ltd. has been installed in No.1 tankhouse."

Jan 1, 2000

By C. Alexandru Sonoc

Donnan Dialysis uses ion exchange membranes to extract and separate cations. The driving force is provided by differences in chemical potential, rather than by electric fields or pressure. A Donnan Dialysis based process to recover lithium, nickel, cobalt, manganese, and organic acid lixiviant from recycled lithium ion battery cathodes is under development. In this paper we present a model of Donnan Dialysis and results of simulations of the aforementioned process. The simulations show that 170 m2 of membranes can process 1000 L of leachate ([Li+] = 0.285 M, [Co2+] = [Ni2+] = [Mn2+] = 0.095 M, pH 2) in two days and recover 94.1% of the lithium (as lithium carbonate), 99.4% of the transition metals (as mixed sulphates ready for solvent extraction), and all of the organic acid using 423 mol of H2SO4 and 268 mol of KHCO3.

By A. E. Clark

Rare earth compounds are widely known as possessing many extraordinary magnetic properties. In this paper, we focus on the huge magnetically induced displacements (magnetostrictions) which characterize the compounds of terbium with iron (Terfenol). Materials prepared commercially by both free-standing-zone (FSZ) and modified Bridgman (MB) techniques have now become available in large sizes and shapes. Prior to the development of the Terfenol alloys, it was possible to achieve giant magnetostrictions only at cryogenic temperatures. In the cubic Laves phase TbFe2 compound, saturation strains exceed 3000 x 10-6 at room temperature and above. Large magnetization 'jumps' can occur, causing huge spontaneous magnetostrictions with small triggering magnetic fields.

Jan 1, 1992