Search Documents

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By Sh. Najisi, O. Lashkari, M. R. Ghomashchi, A. Charette

"One of-the important parameters in casting and foundry technology is the fluidity of molten metal. This parameter becomes particularly important when casting thin wall parts. Therefore, understanding and controlling fluidity plays a major role in fabricating sound and defect-free cast components.Semi-Solid Metai SSM, slurry is a mixture of solid and liquid, mushy zone, with solid volume fractions of 0.1-0.5 and apparent viscosity close to oil viscosity at room temperature. It flows easily under pressure and capable of making complicated shapes with high degree of die filling and integrity.In this study, the ability of the semi-solid slurry to continue to flow is investigated through the effect of different fraction solids and holding temperatures. The results show that in mechanically stirred, MS, semi-solid 356 Al-Si alloy, increasing fraction solid reduces fluidity. Furthermore, the results of MS-alloy are compared with a newly patented Rheocasting route, i.e. SEED, Swirl Enthalpy Equilibrium Device to highlight the differences of the two processes. In addition, the interrelationships between microstructural evolution and fluidity are discussed."

Jan 1, 2004

By Zhigang Zak Fang, Michael L. Free, Jaehun Cho, Syamantak Roy, Amarchand Sathyapalan

Leaching characteristics of impurity removal from the Upgraded Titania Slag (UGS) using hydrochloric and boric acids has been investigated. Specifically, this study has focused on removal of iron oxides from the UGS that has been reduced by hydrogen gas and magnesium at 750oC for 5 hours. Reduced UGS is mainly composed of titanium hydride and impurities like iron oxides, silicon oxide, aluminum oxide, and magnesium oxide. The concentration of hydrochloric and boric acids and the leaching temperature have been chosen as the prime variables to identify the optimum conditions and leaching characteristics for removal of iron oxides. It was observed that under the constraint that 1 wt % of titanium hydride loss is the maximum amount tolerable, 0.1M HCl with 1M boric acid and 90oC are the most effective parameters for iron removal from the reduced UGS. Also, the overall rate of reaction seems to follow interfacial reaction controlled kinetics. The calculated activation energy of the reaction is 73.90kJ/mol.

Jan 1, 2016

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999

By Kenneth L. Reid

The Mineral Resources Research Center at the University of Minnesota has recently installed a QEM*SEM system (Quantitative E.valuation of Materials using Scanning Electron Microscopy) to aid in detailed mineralogical evaluation of potential mineral resource developments in Minnesota and to provide services to the North American mineral industry. A primary application for the unit is to serve the Minnesota taconite industry by providing mineralogical analysis of ores and concentrator products. Minnesota taconite ores contain fine-grained magnetite in a quartz matrix. The ores undergo several size-reduction/magnetic-separation steps to produce a final concentrate with approximately 75% passing 325 mesh and containing about 5% gangue. The paper describes a typical taconite concentrator flowsheet and reports some preliminary results of the applications of QEM*SEM particle image maps and cumulative yield liberation data to samples from selected points in the concentrator circuit.

Jan 1, 1988

By S. Ikenobu

This paper describes a method for processing high-silicate zinc concentrates by hydrometallurgical zinc refining. Silica in concentrates reacts to form zinc silicate during roasting. The zinc silicate readily dissolves and slowly precipitates in sulfuric acid solutions during leaching. However, if proper operating parameters are not maintained, the colloidal silica may form an unfilterable gel. That is, according to the investigation results obtained, the silica concentration in the reactor has to be maintained at 5 g/1 or less (preferably 2 g/1 or less) by promoting the precipitation reaction. The proposed method has made it possible to precipitate silica in a form having excellent solid-liquid separation characteristics, without the need for facilities having a high filtration capacity, and to maintain a low silica concentration in the reactor by feeding a composition containing pre-adjusted silica contents.

Jan 1, 2000

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By Ken Baxter

The Sepon Copper Project is located in Laos and has a mineable reserve of approximately 16Mt of ore grading 5% copper with minor gold and silver values. The deposit is a clay-hosted secondary copper mineral suite, predominantly chalcocitic in nature with associated pyrite. The current project design is based on the production of 60,000t/a of LME Grade A cathode by an acid leaching process followed by solvent extraction and electrowinning. Significant metallurgical testwork was conducted as part of the Definitive Feasibility Study (DFS) with process challenges identified and overcome at each phase of testing. Flowsheet configuration is geared to autogenously generating sufficient acid and ferric iron to meet gangue acid consumption and to leach the copper. The ability to maintain acid and ferric levels in the process liquors is strongly influenced by the proportion of pyrite in the ore presented to the autoclave. This paper will outline flowsheet development from preliminary variability testing to pilot plant and DFS design. The Sepon process solution seeks a balance between operability and capital/operating costs, and provides insights into the basic mechanisms influencing flowsheet selection for these ore types.

Jan 1, 2003

By Peter Olubambi, Babatunde Obadele, Oluwagbenga Johnson

"The microstructure and corrosion behaviour of titanium carbide (TiC) reinforced duplex stainless steel matrix surface composites synthesized by laser melt injection technique was investigated. The surface melting operation was conducted using a 4.4 kW CW Nd:YAG laser with laser power of 1.5 kW, scanning speed of 0.4 to 1.0 m/min, beam size of 3 mm and argon shield gas flow rate of 4 L/min. The morphologies and microstructures of the coatings examined using field emission gun scanning electron microscope (FEGSEM) revealed homogeneous distribution of fine precipitates of TiC in the matrix, while X-ray diffraction (XRD) analysis confirm no phase change. TiC addition to the steels significantly increased hardness value to about 547 Hv0.1 but slightly decreased the corrosion resistance of the steels in 3.5% NaCl possibly due to the intergranular carbide coating that prevented chromium from forming continuous passive oxide layers.IntroductionComposite materials evolve from the idea of combining two basically dissimilar materials with different physical and mechanical properties to arrive at a product whose final properties are superior to those of the individual components [1]. Metal matrix composites (MMCs) are receiving much attention and are the focus of intense research and development worldwide for aerospace, automotive and other applications because of their excellent combination of ductility and toughness of the metallic matrix with high hardness and strength of carbides reinforced in the matrix [2]. Surface modification techniques such as laser, thermal spray, plasma spray, chemical vapour deposition have been use to fabricate MMCs. Laser melt injection (LMI) is a surface modification technique known since the 1980s [3] has been used to improve surface properties of metallic alloys such as aluminium, titanium and steels [4-6]. It involves the lateral injection of carbides, ceramics and cermets blown by a gas stream into a liquid metallic pool, created by laser irradiation of the top surface of the base material."

Jan 1, 2012

By Olga K. Karakasi, Angeliki Moutsatsou, Ioanna Kavallari

"The present study focuses on the amelioration of the behaviour of high calcium fly ash (HCFA), investigating its application in a new environmental field: oil spill clean up. High calcium fly ash is a by-product of electric power plants, produced annually in large quantities, whose greater amount is landfilled. Some of its properties, such as its chemical and mineralogical composition, its fine particle size, its porosity, floating ability and hydrophobic character make it an attractive material for this purpose. Researches showed that when added to an oil spill, it forms a semi-solid phase, which allows the quite total removal of the oil, but it is not stably retained on the surface. In order to ameliorate its floating ability, the decrease in its specific gravity by mixing with a lighter material is investigated. In the present study the mixing with two materials, already used in oil spill clean up, sawdust and a polymer, has been examined. Addition of 15-25% w/w sawdust to HCFA results in a material with better performance than HCFA or sawdust alone: it has a satisfactory floating ability and allows total removal of oil. Addition of the polymer, however, has resulted in no significant amelioration of the oil sorption behaviour of HCFA, probably because no affinity between HCFA and polymer has been achieved.IntroductionCoal fly ash is a by-product of coal combustion in electric power plants, produced worldwide in huge quantities, approximately 500 million tones annually. High calcium fly ash (HCFA) is classified to class C presenting a (Al2O3 + SiO2 + Fe2O3) > 50%. The production of lignite fly ash in Greece comes up to 13 million tones annually, of which only 12% is used in construction applications, the other being landfilled [5, 6].Besides its limited application worldwide as a construction material, research is focusing on the development of new environmental applications, such as waste stabilisation and solidification, soil and water environmental improvement [9, 12]. For the application of fly ash in further environmental fields several chemical modifications have been applied, in order to improve its properties. Extensive research has been focused on the conversion of both coal and lignite fly ash to zeolite and its further application in environmental field, such as the uptake of inorganic (heavy metals and ammonium [8, 11]) or even organic compounds (methylene blue [15]) from waste water streams, or the use as molecular sieves, to adsorb water molecules, SO2 and NH3 from gas streams, due to the high cation exchange capacity and porosity of the produced zeolithic material. Furthermore, lignite fly ash has been combined with sodium silicate solution, prepared by treatment of rice husk ash, and tetrapropylammonium bromide, to synthesise hydrophobic zeolite ZSM-5 [4]."

Jan 1, 2008

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Riyad N. Ahmad-Bitar, Shadia J. Lkhmayies

"CdSi-xTex thin films were prepared by first producing CdS:In thin films by the spray pyrolysis (SP) technique and then annealing the films in the presence of Te vapor in nitrogen atmosphere. X-Ray diffraction (XRD) measurements showed that the films are polycrystalline with the wurtzite structure. Transmittance measurements were recorded at room temperature in the wavelength range 400-900 nm and used to deduce the absorbance. The first derivative of the absorbance was calculated and used to find the values of the bandgap energy, where more than one bandgap was obtained for each film. These results show that the films are inhomogeneous or the composition differs with location. The photoluminescence (PL) was recorded at T = 60 K and a deconvolution peak fit was performed for each spectrum. The results of the PL spectra are consistent with those obtained from the first derivative and confirm the inhomogeneity of the films.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The CdS/CdTe interface plays an active role and a detailed knowledge of its properties is crucial for thorough understanding of the device. High efficiency devices have been obtained in spite of the large lattice mismatch (9. 7%) between hexagonal CdS and cubic CdTe. Interdiffusion at the CdS/CdTe interface is considered to affect the performance of the devices [1]. The formation of a mixed crystal or a graded layer at the interface causes a reduction in the lattice mismatch at the CdS/CdTe junction [2] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [3, 4].The objective of this work is to investigate the transmittance, photoluminescence (PL) and structure of CdSi-xTex thin films prepared by annealing the spray-deposited CdS:In thin films in the presence of tellurium vapor. X-ray diffraction (XRD) was used for exploring the structure. Transmittance is used to deduce the absorbance where its first derivative was used to find the bandgap energy which varies with composition. The evolution of the PL spectra as functions of tellurium concentration was evident and it confirmed the inhomogeneities of the films."

Jan 1, 2011

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By Huaming Yang

Infrared materials are a special kind of material widely used in military, biological engineering and chemical industry. However, the problems associated with them such as unstable properties, high cost and a high thermal expansion coefficient seriously restrict the development and the wide application of the traditional infrared materials with the SiC or ZrSiO4 matrix. The ultrafine quartz powder is normally used to prepare the infrared materials by hot-pressing technology. The aim of the paper is to investigate the thermal expansivity, the effect of the SiO2 size and the addition of AI2O) or Fe2O3 on the infrared emissivity of the quartz matrix of the infrared material (QMIM) in a 8-25um wavelength range. The results indicate that 89% of infrared emissivity and 0.4x 10.5°C of thermal expansion coefficient of QMIM can be obtained. The affeeting mechanism of Al2O) and Fe2O3 on the infrared emissivity of QMIM were also discussed.

Jan 1, 2003