Search Documents

By John A. Mavrogenes

The Texaco gasification system developed at the Monte Bello pilot plant efficiently bums petroleum-coke thereby producing syn-gas and electricity. This system produces more electricity than conventional burners, yet the only by-products are pharmaceutical grade sulfur and V -rich slag. Vanadium is known to exist in multiple valence states in compounds which possess a wide range of melting points and physical properties. Consequently, it becomes important to carefully regulate oxygen fugacity throughout the system in order to control vanadium valence state. Vanadium phase equilibria is presently poorly understood, in large part because of the multiple oxidation states of vanadium (-I, 0, +2, +3, +4, and +5) and the difficulty of unequivocally identifying the valence state(s) in many compounds. The operation of these gasifiers at approximately 1400°C is well above the melting point of V20S but considerably below the melting temperature of V02 and V 203. If J02 can be regulated to keep the burner within the V 205 field, slag material would more likely remain molten and more easily flow out of the bottom of the burner. In pure V oxides. the oxidation state is readily determined by microprobe analysis. where V20S (V+5) is 56% V, V02 (V+4) is 61.4% V, and V203 (V+3) is 68% V. However, V valence in multi-element phases (especially phases containing other elements of variable valence) cannot be resolved by microprobe analysis alone. Petroleum-coke gasification slags collected from within the gasifier under different oxidation conditions were studied by electron microprobe analysis (EMPA). X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Raman spectrometry in conjunction with microprobe analysis was found to resolve the valence of vanadium in the phases of these slags. Raman spectra collected from homogeneous single phase V-oxide standards in vacuum at low temperatures (-150°C) yielded peaks characteristic to each valence state. Gasifier slag samples are, however, much more complicated. Oxidized samples contain: fine grained (Ca. Mg, Fe. V) oxide matrix of variable composition, (Fe. V, Ni) spinel. (Fe, AI, V, Ni, Mg) spinel, V205laths, AI-Si glass blebs and Ni sulfides. Reduced samples contain: crystalline Ca-siIicate matrix, subhedral to euhedral (V, Fe, Mg, AI) spinel, subhedral V02, Fe and Fe-Ni sulfides, Fe-Ni alloys, and complex Ca-oxide matrix. The different spinel assemblages, the characteristic V-oxides and the distinctly different character of the matrices makes the oxidized and reduced slags readily discernible.

Jan 1, 1995

By Donald I. Bleiwas

World primary nickel production in 1987 is projected to be 770,000 mt, slightly higher than that in 1986. Market economy country (MEC) production in 1987 is projected to be about 524,000 mt, an increase of almost 5 pct over 1986 production. Production cutbacks and closures at Japanese ferronickel plants in 1987 resulted primarily from the strong yen and higher energy prices. Cutbacks also caused reductions in ore production from Indonesia, New Caledonia, and the Philippines. Technical problems affected production, to varying degrees, in Botswana, Indonesia, and Yugoslavia. World primary nickel production for 1988 is projected to be 787,000 mt, of which 536,000 mt will be produced in MECs. Increased production is projected from Botswana, Canada, Cuba, and possibly Greece and Yugoslavia, while slight production decreases are projected for Indonesia, New Caledonia, the Philippines, and Zimbabwe. .. South African nickel production in 1988 could be severly curtailed by social strife. In the early 1990's Brazil and China could be major economic competitors to Western nickel producers.

Jan 1, 1988

By John L. Hostetler

GALFAN, the Zn-5% Al-mischmetal hot-dip galvanizing alloy is coated onto steel sheet, wire, and tube using high-speed continuous galvanizing lines. Factors critical to producing high quality GALFAN are reviewed, The relationship between minimum mischmetal content in the GALFAN alloy and furnace dewpoint will be described. The relationship between peak annealing temperature and furnace dewpoint will also be shown. Typical suategies for operating multi-purpose hot-dip galvanizing lines including GALFAN will be described. A recent development has allowed preparation of steel smp for GALFAN coating using aqueous fluxes rather than high temperature annealing. This allows production of GALFAN-coated smp without over-ageing of the steel, and allows high steel strengths and hardnesses to be obtained. The principles of this process will be described.

Jan 1, 1992

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012

By David C. Lynch

FeCl3 particulate of 10 to 100 um in diameter was reacted with radicals produced in an oxygen plasma at pressures between 1 to 20 Torr. The particulate, in a fluidized bed, was positioned above the plasma to avoid over heating the oxide product which is known to lead to crust and clinker formation[ 1 ]. Reaction between the iron chloride and the gas phase occurred at temperatures between 66 and 226 °C. Oxygen radicals react with the surface material to a depth of approximately 2.5 4m. Surface material, analyzed with a x-ray technique, indicates that the maximum amount of FeCl3 reacted on a weight basis was found to be approximately 67%. More typically, 40 to 50 wt% of the chloride was reacted within 30 minutes to 1 hour.

Jan 1, 1996

By Goren Lindkvist

Elkem has a small industrial scale. Muti-Purpose furnace at the MEFOS Metallurgical Research Facility in Lulea, Sweden. The furnace is 2 meters in diameter with installed power of 4.8 MVA, equipped with oil coiled freeze lining, gas tight electrode seals and feed chutes and a slag flow control for continuous tapping. During tests in June, 1991, the furnace was continuously operated on a high silica slag at loads from 1.5 to 4,0 MW. The slag was then charges to a low silica, high iron and lime composition. Steel plant dust was added, smelted and reduced. The slag was made more ceramic by adding alumobrick and alumina. Data from the start-up and initial operating phase of the, Elkem EAF dust plant at Laclede Steel will also reviewed.

Jan 1, 1992

By Denise C. R. Espinosa

The amount of secondary batteries are increasing about 15% by year. Among these batteries, it can be highlighted the NiCd ones, due to their high consumption. In Brazil, the consumption of NiCd batteries grown quickly in the last 5 years, due to the dissemination of cellular telephones and other electronic devices. The first step of a process to recycle spent NiCd batteries is the pretreatment through unit operations of mining treatment. The aim of this work is to define a physical pretreatment to conditioning the waste to a pyrornetallurgical recycling process of spent NiCd batteries used in cellular telephones. Batteries were disassembled by hand to release the different components. The studied batteries are basically composed (by weight) of: 78% nucleus, 18% plastic case and 2% circuits. The grinding of the batteries was performed by knife mill and also by hammer mill. After grinding the material was screened and submitted to a magnetic separator.

Jan 1, 2001

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By James Wang

In July 2003, The Office of Hydrogen, Fuel Cells and Infrastructure Technologies of the Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy solicited Grand Challenge Proposals to establish three Centers of Excellence in hydrogen storage developments for reversible metal hydrides, non-reversible chemical hydrides and carbon storage materials, respectively. The program mission is to research and develop cost-effective, on-board hydrogen storage systems that enable a minimum range of 300 miles within the weight and volume constraints of the vehicle. Currently, no hydrogen storage technology available can meet the DOE cost and performance targets. In April 2004, Sandia National Laboratories was selected by DOE to lead the Metal Hydride Center of Excellence with partners from 5 other national laboratories. We will present the organization and recent accomplishments of the Metal Hydride Center which is confident to accomplish DOE/FreedomCAR and Fuels Partnership objectives for 2010 in hydrogen storage for vehicular transportation applications.

Jan 1, 2006

By Lei Wang, Xiancong Zhao, Hongxu Li, Lifeng Zhang

Recovery of Fe from red mud has been studied using statistically designed experiments. The effects of three factors, namely: reduction temperature, reduction time and proportion of additive on recovery of Fe have been investigated. Experiments have been carried out using orthogonal central composite design and factorial design methods. A model has been obtained through variance analysis at 92.5% confidence level.

Jan 1, 2015

By C. Lupi

Electric arc furnace dust generated during the production of steels is regarded as hazardous waste because of the presence of leachable elements such as Cr, Pb, Cd .... Different processes are available according to the management policy chosen by the steelmaker: disposal. recycle and/or recovery. The feasibility of an hydrometallurgical Zn recovery process on fumes generated during the pyrometallurgical treatment of EAF dust has been investigated. The recovery of metallic iron, chromium and nickel as molten metal provides fumes very rich in zinc oxide ( 63.1% ) and poor in zinc ferrite. This secondary dust is still an hazardous waste and represents the raw material for the recovery of Zn and Pb. The waste material is first leached in 1.5 M sulphuric acid at 30°C to provide a Zn, Fe and Mn rich aqueous solution and a Pb and Ca sulphate rich sludge. The iron is eliminated by precipitation because is harmful to the following electrowinning process. The ftltered and purified leached solution is acidified in order to obtain good electrowinning conditions. A pure cathodic deposit of zinc is then produced in an electrolytic cell at laboratory scale.

Jan 1, 1996

By Philip Thompson

"Carefully planned laboratory test programs provide valuable data regarding the amenability of low grade gold ores to heap leaching. The most common laboratory test is the column leach test. The overwhelming problem associated with this type of test is the limit on the test column height. Most laboratories use a three (3) meter (10 foot) high column as a standard test due to building ceiling limitations, sample size limitations, etc. This paper presents a case study in which an ore sample was tested in a 1.5 meter, a three meter, and a six meter high column to determine the effect of column height on the test results. Other important factors such as sample preparation protocol, preliminary bottle roll testing to determine appropriate crush size, column diameter requirements, and leach solution analyses, are also discussed.IntroductionColumn leach testing has been used for years by many laboratories to determine the amenability of low grade precious metals bearing ores to heap leaching. However, the test work can be compromised by poor planning, misinterpretation of results, and extrapolation of data beyond the reasonable boundaries of the experiment. Preliminary test work should be performed prior to column testing. This preliminary work provides valuable information regarding the response of the ore to cyanidation and aids in the design of the column tests.The sample should be screened into various size fractions prior to testing. The fractions are assayed to determine the gold content of each size fraction and of the overall sample. The most valuable preliminary test is the bottle roll cyanidation test which is usually performed on five kilograms of coarse sample in a large rolling bottle which can accept material up to 50 millimeters top size. The residue from this test is screened at different sizes to determine the distribution of unleached gold in the residue. Comparison of the gold distribution in the leach residue with the distribution of gold in the feed at the same size intervals provides an indication of the appropriate crush size for the sample. The overall gold extraction from the sample at the crush size tested is also determined from these data. Lime and cyanide requirements can also be estimated from this test. The viscosity of the bottle roll pulp and the size distribution of the feed and leach residue can also suggest whether agglomeration of the ore will be required prior to column testing. Ores which contain significant amounts of clays (greater than 5 percent) will generally require agglomeration to prevent plugging of the test column."

Jan 1, 1997

By Daoxin Wu

In this paper, the rutile TiO2 were prepared under air, Ar and H2 calcination atmosphere by low temperature hydrolysis using Tetrabutyl titanate (C16H36O4Ti) as raw material. Powers were characterized by X-ray diffraction, UV-vis diffuse reflectance and X-ray photoelectron spectroscopy. The influence of the calcination atmosphere on the photocatalytic reactivity of rutile TiO2 for oxygen production was investigated. The photocatalytic reactivity of rutile TiO2 prepared under air, Ar and H2 atmosphere was compared under ultraviolet and visible light radiation with Fe3+ (c=8.0mmol.L-1) as electron acceptor. The results showed that rutile TiO2 prepared under Ar and H2 atmosphere had higher photocatalytic activity for oxygen production than that prepared under air atmosphere. The oxygen production rates under ultraviolet irradiation were 427.5, 378.2 and 357.0µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere. The oxygen production rates under visible light irradiation were 78.2, 52.2 and 13.5µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere.

Jan 1, 2008

By Y. Iguchi, T. Narushima, T. Shiozawa, M. Maruyama, R. Arashi

"In situ observation system for thermal oxidation using Raman spectroscopy' was constructed, and oxide films formed on liquid pure Al and Al-Mg alloys (Mg contents = 1 and 4 mass%) were analyzed at room temperature to 1273 K in dry oxygen. In situ Raman spectra of the surface of a liquid Al-:-4mass%Mg indicated the formation of MgO • AlP3 (spinel) as oxidation products, while a -AlP3 and MgO • Alz03 (spinel) were observed on a liquid Al-1mass%Mg alloy. It was suggested that the formation of MgO film affected oxidation behavior of these alloys.IntroductionLiquid aluminum alloys are cast to ingots mainly by the continuous casting process. It is well-.known that surface cracks could be caused by oxide films formed on the surface of melt during continuous casting and defects due to the film. With regard to oxidation behavior of liquid aluminum alloys, many investigations l -s have been carried out from the view point of formation of ceramic metal composites(CMC) which are expected as cutting tools and structural materials 1.2. It is very important for reasonable continuous casting and CMC formation processes to elucidate oxidation behavior of melts.Oxidation behavior of materials generally depends on compositions and properties of oxide films formed on the surface. If in situ observations of oxide films are available during oxidation, evaluation of oxide films and interpretation of oxidation mechanism could be expected. Laser Raman spectroscopy is one of the most appropriate techniques for in situ observation of oxide films under various atmosphere at high temperatures. The authors have discussed the effects of atmospheres and sample compositions on oxide film formation mechanism on Fe-Si alloy6 and SiC-B4C composite7 on basis of an in situ observation by Raman spectroscopy. In spite of many previous studies, systematic and clear explanations have never been gotten on oxidation behavior of liquid aluminum alloys. And no in situ observation has been made except for transmission electron microscopy(TEM) and X-ray diffraction(XRD)."

Jan 1, 1996

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989

By Viktor Mukhin

"Among the methods proposed for spent activated carbon regeneration, the most acceptable is, thermal reactivation, because in this case the existing equipment for manufacture of activated carbon can be adapted for this purpose.In order to conduct the process of thermal re-activation of spent activated carbon directly at gold mills, a fullscale drum-type furnace with external electric heating has been developed, i.e. EPV-300 model with a throughput rate of 50 to 120 kg/hour. Its use ensures restoration of the adsorption properties of carbon up to the level of fresh activated carbon with an insignificant (by 0.7%) decrease in strength and with a high (95% to 97%) yield of reactivated carbon.During the recent years, activated powder carbon has been extensively used in flotation processes for treating polymetallic ores at ore treating plants to improve recoveries of main metals (copper, lead, nickel, etc.).Especially large volumes of activated powder carbon are used at the Talnakh concentrator of the Norilsk Mining and Metallurgical Complex in Russia for absorption of residual flotation reagents from recycled water in order to ensure efficient selective separation of minerals with similar physical and chemical properties.IntroductionSorption technology based on active carbons use starts being applied in such an important in the widest sense of the word strategical branch of economics as non-ferrous metallurgy. Thus since the middle ninetieth Russian gold extraction industry began to apply widely the processes of sorption from pulps and solutions by means of high-resistant granulated active carbons. That provided the start of gold ore minefield exploration, increasing of gold extraction from the ore and reducing its loss with the ""tails"" of process. At present more than 40% of Russian gold is extracted with the help of sorption technologies [1].Another field of active carbons application in non-ferrous metallurgy is the processes of non-ferrous ores floatation at ore-mining and processing enterprise. For that purpose powdered (less than l00µm) active carbons are used for providing the effective selection of minerals with similar physicochemical properties. This method not only increases the metal extraction level but provides deeper division of them."

Jan 1, 2008

By Jozef Zmik, Sergey Dobatkin, Martin Fujda, George Raab, Libor Kraus

"The present work, likewise, deals with grain refinement of medium carbon steel AISI 1045 having different initial microstructure resulting from thermal and/or thermomechanical treatment (TM) applied prior severe plastic deformation. In case of TM treated steel, structure refinement was conducted in two steps. Preliminary structure refinement has been achieved due to multistep open die forging process which provided total strain Eef ~ 3. Uniform and fine recrystallized ferrite structure with grain size of the order of 2-5 µm and with nest-like pearlite colonies was obtained. The further grain refinement of steel samples having different initial structure was accomplished during warm Equal Channel Angular Pressing (ECAP) at 400°C. The microstructure development was analyzed in dependence of effective strain introduced ( Eef ~ 2.5 - 4). Employment of this processing route resulted in extensive deformation of ferrite grains where mixture of subgrains and ultrafine grain was found regardless the preliminary treatment of steel. As straining increases the dynamic polygonization and recrystallization became active to form mixture of polygonized subgrains and submicrocrystalline grains having high angle boundaries. The intensive straining and moderate ECAP temperature caused the partial cementite lamellae fragmentation and spheroidization as straining increased. The lamellae cementite spheroidization was more extensive in TM treated steel samples. The deformation behavior of for both steel structural state confirm the strength increase; however the work hardening behavior was modified with respect to initial structure of steel prior SPD processing.IntroductionIn the last years, ultrafine grained materials have attracted considerable research interest because they tend to possess high strength without sacrificing toughness and ductility. Microstructural refinement of steel is usually achieved by alloying and/or by thermomechanical treatment process, which modifies phase transformation. Recently, advancement of severe plastic deformation (SPD) techniques provides another efficient access for grain refinement of metals and alloys. The fabrication of bulk materials with ultrafine grain sizes has attracted a great deal of attention over the past two decades because of the materials' enhanced properties [ 1, 2]. In last decade a worldwide effort in manufacturing process to obtain ultrafine grain structures in steels is persisting."

Jan 1, 2011

By Laurentiu Nastac

"An advanced casting simulation-based optimization approach was applied in this study to assist in the improvement of the mold design of aerospace components made of A3 56 alloy. By using this approach, mold filling and solidification related defects (including macro-shrinkage and shrinkage porosity) were significantly minimized and hence it helped in cost reduction, performance enhancement and quality assurance of complex A3 56 cast parts.An experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and shrinkage porosities were performed using A3 5 6 plates cast in fiiran-silica sand molds using the Prometal's Rapid Casting Technology (RCT) - mold printing technology. Correlations between Niyama values and the pore percentage were also developed. Thus, the severity level of shrinkage porosity can be determined via the Niyama criterion. Predictions were then compared with the macro-shrinkage and porosity measurements in plates of various plate thicknesses and in other commercial A3 56 casting components.IntroductionThis paper describes the process modeling approach used in the development of the mold design technology used to produce assist in the improvement of the mold design of aerospace components made of A356 alloy. Nova Flow&Solid™ software [3] was applied in this study. This casting simulation software was previously validated for several alloys including Ti, steel and superalloys [1-4]. The objective of this paper is to calibrate and validate the simulation software for A356 alloy sand mold castings. For this purpose, an experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and microshrinkage (e.g., shrinkage porosities) were performed using A356 plates cast in fiiran-silica sand molds using the Prometal Rapid Casting Technology (RCT) mold printing technology. The details of the RCT technology are shown in Fig. 1 [5]. Prometal's RCT technology is used for rapid production of sand molds and cores directly from CAD files. The RCT technology relies upon ink jet printer technology to selectively bind the grains of sand to create three-dimensional sand molds and cores. Mold filling and solidification modeling as well as stress analysis are typically performed to properly design the casting and the rig system of each prototype component."

Jan 1, 2012

By Duck Jae Lee, Kwan Ho Kim, Ji Whan Ahn

"In Korea, reutilization of constructions waste is gaining an increasing attention as generation of construction waste is projected to increase continuously. In current practices, the concrete waste is simply crushed and used as a low application such as paving, back filling, etc. In this study, a new process was developed comprising of heat pretreatment, autogenous milling, and density separation for complete reutilization of concrete waste. Firstly, the concrete waste was crushed using autogenous milling. The coarse size fractions from autogenous milling have a density of 2.5g/cm3 and a water absorption ration 3.0%, which meet the specification of the first class of KS F 2573. The fine size fractions were further separated using a hindered-settling column into two products 1) underflow, 2) overflow. The underflow sample was a high quality fine recycled aggregate which can be used for concrete making, and the overflow sample was an enriched cement material can be also used for CO2 sequestration by mineral carbonation. Introduction Kwan Ho Kim1, Ji Whan Ahn2, Duck Jae Lee1, Hee Chan Cho1 Recently, the importance of resource recycling is gaining a greater attention due to the increasing price of natural resource. Recycling is beneficial for not only the management of waste, but also the reducing of consumption of natural resources and huge energy consumption to treat of natural resource. The construction and demolition waste comprises the major industrial waste generated in Korea. It increased to 54 million tons in 2004, and is projected to increase to over 300 million tons in 2020, as many buildings reach the end of their 30 years life. Among total waste, the proportion of concrete waste was about 30% in Korea. Due to its large volume, recycling of concrete waste is the most important aspect of the waste management. In the current practices, the concrete waste is simply crushed and used as a recycled aggregate. The recycled aggregate has a low quality and most of them are down cycled for usage as paving material, back-filling material, concrete bricks, etc. It cannot be reused for replacement of natural aggregates because cement mortar is not separated perfectly from aggregates. These kinds of recycled aggregates tent to be weaker, more porous and have a higher value of water absorption. When these aggregates are used in concrete making, there are problems of higher total water demand, low compressive strength and durability [1-5]. And recycled fine aggregate is not almost recycled due to its low quality. In this study, a new processing circuit is developed to produce not only highquality recycled coarse aggregates but also fine aggregates and cement material from concrete waste."

Jan 1, 2008

By Vladyslav P. Yakubovsky, Boris I. Bondarenko, Valentin A. Noskov, Vladyslav M. Sokolov

"Each of Ukrainian producers of ferronickel, stainless steel and synthetic diamonds has the same basic problem with recycling their fine Ni-containing secondary materials. The conditions for generation of them along with the correspondent properties were investigated in details. The new approaches for their recycling have been proposed. They are based on application of some pyrometallurgical processes that are used in Ukraine. The proper equipment is also available. It has been shown that the dust from laterite calcining process of ferronickel production should be efficiently recycled by sintering. The stainless steel dust should be smelted after briquetting as a charge addition to the Ni-containing discarded batteries in the elaborated furnace. The sludge after synthetic diamonds production should be pelletized and processed by liquid cast iron with application of induction magnetodynamic forces in the specific furnace.IntroductionThe object of the investigation is recycling the Ni-containing secondary fines in a form of dust and sludge. There are several generators of the fines in Ukraine. Namely they are Pobuzhye Integrated Ferronickel Mill; Electrometallurgical Works “Dneprospetsstal” with stainless steel plant as well as Poltava Diamond Plant that produces synthetic hard materials. Their businesses are the largest in the Commonwealth of Independent States (CIS). However the status of handling with the fines is not perfect since the applied recycling technologies are low efficient. The landfilling option is often adopted for them. At the same in Ukraine there are some nontraditional pyrometallurgical recycling technologies and equipment that should be tried for application in smelting these secondary materials.Recycling the sludge of synthetic diamonds productionThe sludge of “Poltava diamond plant” from production of synthetic hard materials has a following chemical composition, %: iron oxide – 29.7; chromium oxide – 18.97; nickel – 4.27; manganese oxide – 15.2; sulphate – 3.85; natrium – 14.9. The content of moisture is 70-80%. The moisture quite quickly evaporates while keeping sludge out of doors. Sludge returns into the weak agglomerates. The sizing of the dried sludge particles presents the figures from 400 to 1000 µm. The moisture was extracted by sludge pressing. The content of the basic compounds of the moisture is, g/dm3: chromium oxide – 1.6; nickel – 0.001; manganese oxide – 0.002; lead – 0.005; sulphate – 13.6; natrium – 17.0."

Jan 1, 2008