Search Documents

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

The fraction of liquid phase in sintered ore can be the most important factor to determine the sinter quality and yield in sintering process. The generation ability of liquid phase for mixture of iron ore powders is determined by basicity, roasting time, roasting temperature and chemical composition of iron ores. Five different iron ores were selected in this study and the dried powders of iron ore and CaO reagent (<200 mesh) were homogeneously mixed together at their required proportions, then 15g of the mixture was pressed under a pressure of 20MPa to make a cylindrical sample with a diameter of 20mm. The sintering temperature in this study was kept at 1280℃, the gas phase is air, the holding time was varied with its three levels of 5min,10min and 15min. After that, the sample was cooled under room temperature in the air, and the cooled sample was analyzed by using zeiss optical microscope. The mineral phase compositions were quantitatively determined with an open source image processing software, Image J whicn can calculate the fraction of liquid phase. Besides, the study on how to estimate the sintering behavior of the raw materials in different conditions by the theoretical calculation is of vital importance, and the development of this will greatly improve the sintering production. Factsage will be used to calculate the liquid phases formulation during the sintering. Comparing the experimental results and the theoretical calculation shows that the mass of liquid phase increases with increasing basicity during the sintering, besides, the mass of calcium ferrite increases with increasing basicity. The generation ability of liquid phase of iron ores can be predicted through the experiment verification.

Jan 1, 2015

By C. Koopman

During the production of phosphoric acid from phosphate ore and sulfuric acid, large amounts of calcium sulfate are formed, in which impurities from the feedstock are incorporated. To use the calcium sulfate in, for example, the building industry, a lower concentration of impurities is desired. Mercury, copper, lead, and cadmium were extracted from clear industrial recrystallization acid (0.8-3.9 mol/kg H3PO4, 0.2-0:5 mol/kg H2SO4) by supported solvent extraction with the extracting agent Cyanex 302 in kerosene in a transverse flow hollow fiber module. The permeability for the mercury ion was 1.4.10-6 m/s, whereas that for the copper ion was calculated to be 1.5.10 m/s. Cadmium, lead, and copper were extracted during the recrystallization of calcium sulfate hemihydrate to dihydrate, an existing step within the ,phosphoric acid production process, by solvent extraction with the same extracting agent. The concentrations of cadmium and zinc in the newly formed calcium sulfate were proven to be decreased. Unfortunately, concentrations of mercury and lead were too low for analysis.

Jan 1, 1999

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By Huimin Lu, Lian Zhou, Qiang Li

"A three-dimensional mathematical model is developed for the regenerative rotary hearth furnace with 40 meters medium diameter. The influence of combustion switchover and outlet pressure on the fluctuation and distribution of temperature and pressure is studied with numerical simulation method. The results showed that the temperature field and flow field is suitable for requirement of industrial production; the fluctuation of the temperature field and pressure is acceptable; the influence of outlet pressure on the furnace pressure is great.IntroduceRotary hearth furnace which is originally utilized as heat treating and reheating industrial furnace, now is also used for carbon based DRl production. With the need of market and the concern of resource recycling and environmental issues, the DRl production from ore or from waste material by rotary hearth furnace attracts more and more attentions from steel industry [1,2].When rotary hearth furnace works, the feed pellets are charged on the hearth and rotate within an annular furnace chamber with the process of reduction. For the sake of rapid reduction, usually the depth of the pellet is one or two layers, accounting for less than 90% of the volume of furnace. As result, the exhaust gases carry away a lot of heat, so that energy utilization efficient is low [3]. Currently, in order to reduce the consumption of energy and improve the production efficiency, many methods have been adopted. The regenerative combustion technology is one of the most promising."

Jan 1, 2013

By L. W. Beckstead

The use of acid ferric sulfate solution as a lixiviant for chalcopyrite concentrates has been of little interest from a practical standpoint due to the formation of a tenacious layer of elemental sulfur which severely impedes the reaction progress. CuFeS2 + 4Fe+3 ?Cu+2 + 5Fe+2 +2s° For example, an acid ferric sulfate leach of chalcopyrite concentrate results in only 12% copper extraction in a three hour leach at 93°C. Experimental results suggest that particle size is the only controllable variable which has a significant effect on the rate of acid ferric sulfate leaching at ambient pressure. Size reduction of the concentrate prior to leaching was exam¬ined using various methods of grinding. Of the grinding methods considered, attrition grinding was found to be the most effective. Leaching of an attritor-ground product (median particle size 0.5 microns) resulted in approximately 90% copper extraction in a three hour leach at 93°C. Energy measurements suggest that the costs associated with attrition mill¬ing are not unreasonable. Evidence indicates that "activation" or stored strain energy is not responsibile for the enhanced reaction kinetics of the finely ground concentrate, but rather the experimental results can be explained simply in terms of the increased surface area due to size reduction. Leaching reaction mech¬anisms operative in the acid ferric sulfate system are discussed and the application of ultra-fine grinding technology to other systems is considered.

Jan 1, 1976

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Wang Shuchan, Zhang Zimu, Zhang Dianhua, Liu Yan, Zhang Ting-an, Zhao Qiuyue, Lv Chao

Rare earth extraction tank has many adverse effects like big floor space and high production accumulation during industrial production. Current researches usually focus on changing the device structure without making a breakthrough towards gravity clarification. This paper attempts to achieve this goal by using both the action of clarification by gravity and clarification by stirring. Because many physical parameters affect the clarification and separation rates, the density, viscosity and surface tension of the two phases were determined at different temperatures and different concentration of aqueous solution. The innovation of this research involves adopting the Karl-Fischer method to investigate water content in oil phase during the stirred separation process. In this paper, the separation effect of different physical parameters was studied and the dimensional equation between water content and the physical parameters was established by combining with the experimental data.

Jan 1, 2014

By W. J. Guay

Scrubbing of simulated copper reverberatory furnace gases containing 1.0 percent sulfur dioxide with the minus 74 ~m fraction of the San Manuel tailings has shown sulfur dioxide removals of almost 100 percent over an effluent pH range of 3.1 to 4.6 and a wide range of liquid to gas ratios with absorptions of 11 to 17 Kg of sulfur dioxide per tonne of minus 74 um slimes. The high reactivity of the tailings slimes with S02 indicates that the reaction rate is not controlled by the slow dissolution of calcium carbonate in sulfurous acid which characterizes scrubbers using ground limestone. The interpretation of these results has been considerably enhanced by wet chemical analysis and emission spectrographic analysis which show that calcium and iron account for about 90 percent of the SO2 absorption with the rest being accounted for by aluminum, magnesium, potassium, and sodium. Mineralogic examination confirms the, chemical and spectrographic analyses showing that the major constituent removed from the slimes is calcium carbonate, with lesser amounts of chlorite and montmorillonite (silicates containing iron, magnesium, aluminum, and calcium) being removed.

Jan 1, 1981

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By Fiseha Tesfaye, Pekka Taskinen

"A thermodynamic study of the equilibrium phase assemblage AgBi3S5-Bi2S3-S was made by an EMF-technique, using the RbAg4l5 solid electrolyte. The ternary phase was synthesized from the pure Ag2S and Bi2S3 in an evacuated silica ampoule and grinded into powder and mixed with appropriate compositions of B12S3 and S, in a series of experiments, for pressing in to pellets. The pellets were assembled to form the galvanic cells Pt (-) | Ag ] RbAg4ls | AgBi3S5+ Bi2S3 + S + (C) I Pt (+). The EMF-measurements were made in the temperature range 299 - 460 K.In this paper, thermodynamic functions of the ternary phase AgBi3S5 (pavonite) have been determined. The agreement between the obtained results and the literature values were established.IntroductionThe complex group of ore minerals constitutes from trace amounts to a major proportions of sulfosalts. Although the sulfosalts rarely form massive ore bodies, they are commonly associated with rich sulfide ore minerals for the base and precious metals and widely distributed in a metal poor sulfide minerals [1]. For instance, Ag-bearing sulfosalts are encountered in ore minerals for the production of the base metals and are common sources of silver. Nevertheless, thermodynamic properties of the sulfosalts are poorly known.Reliable thermochemical data are essential for quantitative modeling of the chemical behavior of the sulfosalts in equilibrium with sulfides, which in turn would promote the optimization of complex minerals treatment and extractive metallurgy of the valuable metals."

Jan 1, 2012

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013

By Stavros A. Argyropoulos, Michael Trovant, Norman J. Goudie

"Two studies were carried out to estimate the thermal resistance of various interfaces using experimental and computational techniques. Three types of interfaces were examined. The first study investigated metal-mold interfaces, and the second study focused on metal-metal and metal-oxide interfaces.For the metal-mold interface, the air gap size was measured and subsequently correlated with the interface thermal resistance. The procedural details are outlined for the development of a correlation which predicts thermal resistance as a function of air gap size.Investigation of the metal-metal and metal-oxide interfaces employed data from a series of experiments as input into a model, which solved the inverse heat conduction problem in terms of a resistance estimate. These experiments, involved dipping a cold cylindrical metal into a liquid metal or liquid oxide, respectively. Under these conditions, a shell freezes around the cylindrical addition and a thermal resistance develops during the time period which shell exists . The Heat Transfer Coefficient (HTC) at the addition shell interface differs significantly among the various types of metals and oxides used. In the case of an oxide shell, the (HTC) is about an order of magnitude lower than the (HTC) of the metal shell.INTRODUCTIONIn many metals processing operations there is a need to estimate the thermal resistance at metal-metal, metal-oxide, metal-mold interfaces. This need was further intensified with the recent proliferation of mathematical models, which predict various transport phenomena events. There are many factors which can influence the magnitude of the interfacial thermal resistance. Some of the factors, among others, are as follows: contact temperature, metal thermal conductivity, apparent contact pressure, surface roughness, interstitial gas conductivity, and interstitial gas pressure.In this paper, two studies are reported on the estimation of thermal resistance. The first involves, the development of heat transfer coefficient-air gap relationships at the metal-mold interfaces. The second includes, estimations of thermal resistance at the addition-shell interface. The former case is encountered in the metals solidification and the latter during the melting and/or dissolution of additions to liquid metals or slags."

Jan 1, 1999

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By Roderick Guthrie

Gas injection into liquid steel baths is widely practiced, ever since the early days of Bessemer’s pneumatic steelmaking process. What has not been fully appreciated is the critical role of bubble sizes for delivering higher quality commercial steels than is presently possible. This was first proposed by Prof P. Hayes and his research group. Using a full-scale water model of a typical 4-strand Ladle-Tundish-Mold system, we demonstrate the potential advantages of modifying a typical ladle shroud, to generate microbubbles within the water flowing into the tundish. This is possible by taking advantage of high shear rates and turbulence kinetic energy available in that region. These microbubbles enhanced the removal of “micro-inclusions” (hollow glass microspheres) in the 5–50 micron size range, to the upper surface of the tundish. There, they were absorbed into an overlaying “slag” phase. Accompanying CFD studies confirmed that no microbubbles in the size range generated (500–900 μm), pass through the submerged entry nozzles into the moulds.

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with CO2 is expected to occur at as low temperature as possible. In order to get a highly reaetive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of CO2. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining all the obtained data.

Jan 1, 2003

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By A. V. Tarasov

A flow-sheet for waste-less processing of spent lead batteries comprises mechanized separation of batteries, smelting of the metallic fraction in a kettle, electrothermal smelting of oxysulfate fraction, refining of crude lead and processing of reverts to produce commercial products. Smelting of lead-containing fraction is performed in an electrothermal furnace using a processing technology developed in the Gintsvetmet Institute and differing from conventional processes by the fact that it does not require any fluxing agent (soda); no matte is formed in the process and the amount of slag produced is minimal, because its formation depends only on the ash content of coke and the quality of battery scrap separation. The process has been patented. It has been introduced on a commercial scale in 1.8 MVA furnaces at the plant of A0 "RyazTsvetmet" (Ryazan, Russia). The process has the following main advantages as compared with conventional shaft-furnace smelting and smelting in a short-drum furnace: the process does not require technical-grade oxygen, the amount of process gas generated is minimized ensuring a decrease in lead-containing dust and sulfur dioxide emissions by 3 to 5 times per unit of lead recovered; a decrease in dust entrainment resulting in lower amounts of recycled dust; lower slag yield (a decrease from 20-25% to 3-5%); lower coke requirement (a decrease from 10-14% to 3-4%). Refining of crude lead is performed using conventional technology but there are several unique features for which know-how is available. Processing of by-products of electrothermal smelting and secondary lead refining (slag, drosses, skimmings) and ebonite fraction (crushed battery casings) is performed in a slag-fuming furnace.

Jan 1, 2002

By Martin Reyes, Juan Hernández, Julio Cesar Juárez, Isauro Rivera, Ma. de los Ángeles Hernández, Francisco Patiño

The dissolution of Ag contained in metallurgical tailings was studied by adding ions Cu2+ and Zn2+ in S2O3 2- medium. Chemical analysis of mine tailings by cupellation revealed a Ag concentration of 71 g/ton. The XRF and XRD analysis confirmed the preponderance of SiO2 in the mineral matrix. The experimental dissolution process was conducted in alkaline solution using six concentrations of NaOH and five of S2O3 2-, at different temperatures, also using five concentrations of Cu2+ and Zn2+ as a catalyst. The results showed similar values for both systems (96.8% and 97.13%). The ion Cu2+ and Zn2+ increases the dissolution of Ag, and decrease the reaction time of dissolution. Under the conditions used, pH and stirring rate did not affect the dissolution of Ag.

Jan 1, 2015