Search Documents

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By Matthew Jeffrey

Due to the increasing environmental and public concerns over cyanidation, there has been a large amount of research into viable alternative lixiviants. Despite these studies, there is little published data directly comparing the kinetics of gold leaching for each of these alternatives: most of the literature is concerned with gold extraction from ores. This paper presents a detailed kinetic study of gold leaching in cyanide, armmonia/thiosulfate and chloride/hypochlorite solutions. The gold leach rates were measured using a rotating electrochemical quartz crystal microbalance (REQCM). This instrument allows the mass of a gold sample to measured in?situ, with a sensitivity of less than 10 ng. From the results of these studies, it is possible to select experimental conditions where the leach rates of the alternative lixiviants are similar to that for the traditional cyanide system.

Jan 1, 1998

By François Tremblay

It is well known that removal of organic material such ,as Jacquer, paint, plastic prior to melting improves aluminum recovery. In addition to being an important economically, decoating of aluminum scrap has a positive impact on the environment, through better control of gaseous emissions. Most of the existing thermal decoaters for aluminum have been designed to operate with scrap containing a level of organic material lower than 10%. The main field of their present application is for recycling of used aluminum can, where levels of organic material are lower than 4%. Alcan has recently developed a new thermal decoating system in order to extend applications of this process to a much wider variety of aluminum scrap. The new decoater efficiently processes aluminum scrap with a level of organic material up to 50%. This new technology features the use of fluidized bed technology to thermally control the process. This innovative feature improves both performance and control over conventional delacquering systems based on hot air convection. This paper describes the basic principles of the technology and the design of the? first industrial unit commissioned by the Alcan Recycling plant in Shelbyville (TN) at the beginning of 1994. Typical applications and operating advantages are discussed.

Jan 1, 1995

By Yousef Mohassab, Manoranjan Misra, Monalisa Panda, Eman Wahbah

This work studies the removal of arsenic (V), arsenate, and arsenic (III), arsenite, from aqueous solution using calcined Quintinite-3T. The two adsorbents Quintinite-3T was prepared, calcined at different temperatures, and characterized by XRD, BET, and SEM. The surface area of the calcined Quintinite-3T was 193.4 m2/g. The particles size ranged from 12 to 56 nm for the uncalcined Quintinite-3T and from 24 to 42 nm for the calcined Quintinite-3T. Kinetic analysis, adsorption isotherm, and factors affecting the adsorption were investigated. Calcined Quintinite- 3T retained As(v) and did not release it back to water even after an entire month.

Jan 1, 2016

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By Sylwia Zymankowska-Kumon, Rafal Danko, Mariusz Holtzer, Artur Bobrowski, Michal Kubecki

"Moulding sands with furan resin constitute constantly growing part in technologies of producing castings from iron alloys. Due to the presence of harmful substances in resins such as furfuryl alcohol, phenol and formaldehyde, using those mould sands may be hazardous to the natural environment and workers. The general assessment of harmfulness of sands used for molds and cores encompasses 2 basic points: emission of hazardous substances during processes of preparing sands, pouring mold with liquid metals (high temperatures), cooling and shaking-out; possibility of washing out hazardous substances from used sands to the environment, during storage or economic use outside foundries. We present the results of research on the assessment of harmfulness of mould sands with furan resin in the scope of the above points. The research was conducted according to the original method prepared by the authors, which has been used for years in cooperation with various foundries (Poland, abroad).IntroductionSands are used by the foundry industry to create metalcasting moulds, where the individual sand grains are typically bound using bentonite clay and carbonaceous additives or resins. During the casting process, the moulds can be exposed to temperatures as high as 1500°C depending upon the metal being poured. The molten metal causes thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics that are emitted to the atmosphere and condense in the moulding sand [1]. The moulding sands are reclaimed within the foundry, but part of them are eventually discarded in landfills, because it is not longer suitable to make metalcasting molds [2, 3]."

Jan 1, 2013

By Emil B. Milosavljevic, Ljiljana Solujic

Cyanide is exceptionally reactive, and in typical gold/silver processing liquors, cyanide may be transformed into various species and forms depending on the mineralogy of the ore and chemical make-up of the process water. The exact speciation and relative concentrations depend on the Eh and pH values, as well as the free CN concentration in the system. Very good cyanide balances can be achieved by the judicious selection of the analytical techniques used. The choices an analyst has to make (which analytical methods to use and which ones to avoid) in order to gain better understanding of cyanide speciation and balances in a particular system under investigation will be discussed. Examples of cyanide balances obtained for the laboratory scale tests (agitated leach and column tests) will be presented and discussed.

Jan 1, 1999

By W. L. Dalmijn

The processing of scrap and scrap cars starts with size reduction by a hammermill, or shredder. After the liberation the magnetic fraction is removed. The remaining non¬magnetic fraction mixed with other materials is screened and each fraction is processed separately. The increased use of plastic has a negative effect on the recovery of metals and waste production. At Huron Valley, Belleville Michigen, USA, the non-ferrous fraction from 5 million obsolete cars per year, containing 200,000 tons of non-ferrous metal, is processed. Aluminium Is recovered with a heavy medium separation process and concentrated with eddy current separators. The remaining heavy non-ferrous fraction is concentrated by a new combination of eddy current separation and image processing. After this separation process the zinc fraction is melted and refined and the copper, brass, stainless steel and other high-quality concentrates are sold to the secondary industries. The recycling of car scrap has become an important source of metals and materials for the secondary. materials processing industry.

Jan 1, 1995

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By Lan Li, Izaak Williamson

"The efficient separation and storage of CO2 from power plant flue gases can reduce the amount of CO2 released into the atmosphere and mitigate global warming. Potential candidates for industrial applications are solid sorbent materials. Crucial factors to control the efficiency of porous sorbent materials include the framework and pore structure, and the chemical and physical reactivity of CO2 within the pores. Computational modeling approaches, based on density functional theory (DFT) and van der Waals-DFT, have been applied to nanoporous solid – manganese dioxide a-MnO2. We found that the types and charges of cations as dopants in the a-MnO2 and the concentration of CO2 influence the structural features of a-MnO2, which control its CO2 selectivity performance within the flue gases.IntroductionCarbon capture and storage is a technique to separate large quantities of CO2 from power plant flue gases before being released into the atmosphere. Porous solids are a potential candidate as sorbents to “trap” CO2 through chemical or physical adsorption on their porous surfaces[1]. Such separation efficiency is determined by the size and shape of its pores and by the interaction between the porous surface and the gas adsorbates. The incorporation of cations into the pore can act as a means of structural support and alter the pore diameter to be comparable to the kinetic diameter of the gas adsorbate, such as CO2.A porous solid of particular interest for CCS is manganese dioxide a-MnO2, an octahedral molecular sieve (OMS) composed of edge-sharing MnO6 octahedra that are linked into a nanoporous framework[2]. The framework consists of (1×1) and (2×2) tunnels, referred to as OMS-2. Due to the larger tunnel size, cations and gas adsorbates prefer to reside along the (2×2) tunnel axis of the OMS-2. As seen in Figure 1, a potassium cation K+ is located in the (2×2) tunnel, known as cryptomelane-type MnO2. Its pore diameter of ~ 4.6 Å gives it a good CO2 selectivity performance, because the diameter is comparable to the kinetic diameter of 3.3 Å for CO2[3]. Alternatively, replacing potassium K+ with other cations, e.g. barium Ba2+, sodium Na+ or lithium Li+, in the OMS-2 tunnel is of great research interest, due to the effects of their concentrations, types and charges on the CO2 selectivity efficiency and sorption hysteresis phenomenon[2,4]."

Jan 1, 2014

By C. M. F. Vieira

The main characteristics and physical and mechanical properties of clays from the county of Campos dos Goytacazes, located at the northern part of the State of Rio de Janeiro, Brazil, are presented. The characterization included mineralogical composition, chemical composition and particle size distribution. The properties related to water absorption, linear shrinkage and flexural rupture strength were obtained in samples that were prepared by 20 MPa uniaxial pressing and fired at 950 and 1100oC. The results showed that the clays are predominantly kaolinitic with high percentage of clay minerals. The kaolinitic structure associated with a small amount of fluxes confers a refractory behavior which makes difficult the sinterization and impairs the ceramic consolidation.

Jan 1, 2009

By J. E. Allen

The trend in refractory technology for the copper and nickel industries has been to higher quality raw materials and improved processing technology. These changes have been dictated by the changes in pyrometallurgical processes in these industries. For example the introduction of flash smelting, reaction type smelting and auxiliary slag cleaning furnaces havedemanded better refractories materials. Extensive field applications and improved laboratory testing procedures have helped make this transition possible. Changes in refractory technology, primarily in basic refractories, are followed from the late fifties to the present and into the future.

Jan 1, 1994

By Alessandro Blasi, Massimo Morgana, Corradino Sposato, Pietro Garzone, Giuseppe Devincenzis

The rare earth elements are essential for a diverse and expanding array of high-technology applications, which constitute an important part of the industrial economy of the 21st century. As a matter of fact, rare earth has been listed in the category of strategic elements in many countries becoming a core business for international research. Experimental tests have been carried out on a bench scale battery of mixer settler composed of 24 stages, each one with a volume of 150 ml. These trials have been performed at room temperature checked by a micro-climatic control system. The battery was setted in two sections: extraction and scrubbing section. Rare earths concentrations were obtained by ICP-OES analysis made on aqueous phase and on the stripped from organic phase. We obtained a complete separation of light rare earth (La, Ce, Pr, Nd) in two sub-groups: La/Ce and Pr/Nd.

Jan 1, 2014

By I. H. Gundiler

Sandia National Laboratories (SNL) is tasked to support The Department of Energy in the dismantlement and disposal of SNL designed weapon components. These components are sealed in a potting compound, and contain heavy metals, explosive, radioactive, and toxic materials. SNL developed a process to identify and remove the hazardous sub-components utilizing real-time radiography and abrasive water-jet cutting. The components were then crushed, granulated, screened, and separated into an aluminum and a precious-and-base-metals fraction using air-tables. Plastics were further cleaned for disposal as non-hazardous waste. New Mexico Bureau of Mines & Mineral Resources assisted SNL in investigation of size- reduction and separation technologies.

Jan 1, 1995

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By Serge Lavoie

Alcan's Guillaume-Tremblay plant, located in Jonquiere, Quebec, has been in operation since 1990. This was the first plasma dross processing plant ever built. In addition to the use of the plasma heating technology, Guillaume-Tremblay has other unique features making it a modern and efficient dross processing facility. This paper presents a general overview of the practical experience at the Guillaume-Tremblay plant. In particular, the utilization of plasma heating in industrial conditions, the metallurgical performance, the unique dross handling system, the control and information management system and the reclaiming of the by-products will be discussed. Finally, the use of the plasma process for salty dross will be addressed' briefly.

Jan 1, 1995

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By René Bustamante

The subject of this paper is a comparative evaluation of different copper smelting gas cooling techniques, using "productivity and quality" criteria. The first section presents a brief description of the operation of the radiant and the evaporative cooling systems, focusing on the differences between each other, in particular regarding. a) mass and energy balances; b) gas flow, temperature and composition; c) dust concentration and recovery. This section includes a brief discussion of the "client-server chain", i.e. the links between the cooling equipment and the down-and up-stream operations. More in particular, the up-stream server relationship impacts on the operating stability of the furnace, and in turn on furnace down-time and Cu production losses; and the down-stream client relationship affects the operation of the electrostatic precipitators, in terms of workload and cost of handling larger quantities of dust of a given dust size The second section deals with the development of indexes to measure and compare value added through the "utilization, productivity and quality" that can be expected of both cooling methods at the physical and economic levels, and the impact on the overall smelter productivity and the final cost composition of copper. The final section presents the results and includes a discussion of the comparative advantages and disadvantages of both cooling systems.

Jan 1, 1999

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By T. Shibasaki

Purification of copper electrolyte at Naoshima is carried out by two stage liberation to completely depress copper and impurity ions followed by concentration of the solution to produce crude nikel sulfate as by-product. A new nickel recovering process has been developed and pilot tested recently. It consists of the following process steps.; neutralization of spent electrolyte from liberation section to remove free acid and most part of remaining impurity ions, refining and nickel concentration by solvent extraction, and crystallization of pure nickel sulfate from concentrated strip solution. This paper describes the results of laboratory and pilot plant tests, then briefly discusses feasibility of the proposed process.

Jan 1, 1987