Search Documents

By Miller, Geoffrey W.

The Ravensthorpe Nickel Project (RNP) flow sheet provides for the upgrading of Ni & Co in a size based beneficiation process prior to leaching. The upgrading effect on Ni and Co makes the beneticiation process a powerful addition to the flow sheet. Multiple linear regression (MLR) analysis based on 351 individual batch tests, 52 large scale composites and 21 pilot plant tests has been used to successfully model beneticiation product grade, recovery, upgrade and mass recovery. Statistically, 83% and 96% of the variability in nickel recovery and nickel product grade respectively was accounted for. Algorithms have been developed for Ni, Co, Mg, Al and Fe, which represents the revenue and operating cost factors for the process. The algorithms have subsequently been applied to the resource model, allowing prediction of elemental grade and recovery for the development of the mine schedules based upon these parameters and not head grades alone. This has allowed optimisation of the mine schedule for improvement to the project's NPV. Keywords: Ni Laterite, Prediction, Multiple Linear Regression, Beneficiation

Jan 1, 2004

By A. W. Worcester

The plant is designed to produce 60,000+ tons of refined lead per year from a nominal feed consisting of 110,000 tons of SLI and industrial batteries, and 10,000 tons of lead contained in drosses and scrap. The plant will also produce as by-products polypropylene chips and detergent grade sodium sulfate, using the Engitec Impianti CX Technology. The battery separation circuit will consist of a battery breaking hammermill and a vibrating screen with water sprays to separate the battery paste from the grid metal and other battery components. The battery components, consisting of ebonite, and separator materials, will be separated' from the grid metal and classified with the use of hydrodynamic water separators. The battery paste will be treated with sodium carbonate to produce a lead carbonate paste for smelting in a reverberatory furnace. The slag from the reverberatory furnace will be campaigned through a traditional primary blast furnace to produce hard lead. The sodium sulfate liquor from the lead carbonate filtration step will be crystallized to produce anhydrous sodium sulfate. The metallic grid metal will be treated through a small rotary smelter of the Engitec design to produce a hard antimonial lead. The plant's scheduled to be commissioned 12 months after receipt of all of the Federal and state permits. The plant will be integrated into the Buick Primary Lead Smelter, located in the center of Missouri's New Lead Belt, at Boss, Missouri. This will allow The Doe Run company to fully utilize all of its existing assets.

Jan 1, 1990

By G. Archer

ASARCO, a large and diverse producer of nonferrous metals, is involved primarily in the smelting and refining of lead and copper. Lead-antimony alloys, antimony trioxide, bismuth, cadmium oxide, selenium, tellurium, silver and gold are among products which result from processing by-products of smelting and refining. The complex mixture of concentrates at some smelters and the high impurity loads at some refineries result in various drosses, sludges, dusts and slags. In this paper, the complex interplant and intraplant transfer of by-products is addressed. These by-products result in an exchange of metals between the lead circuit and the copper circuit. Examples of the transfer of by-products and the prospects for the recycle of valuable products from wastes generated by customers and unrelated processors are also discussed.

Jan 1, 1992

By P. R. Khangaonkar

The variety of intermediates, middlings, complex materials and wastes produced in the conventional processing of tin ores as experienced in the tin industry in South East Asia is reviewed. The problems associated with the treatment of these materials so as to produce useful products by hydrometallurgical or pyro-cum-bydrometallurgical approaches are discussed. Results of treatment of amang middlings consisting of cassiterite, struverite, ilmenite, zircon, monazite etc by chlorination with carbon tetra chloride are presented. The efforts to leach tin without letting iron coming in, by alkali leaching of certain wastes of tin processing are also briefly indicated. It is felt that pyro-cum-hydrometallurgical approach can help a viable treatment of these materials so as to obtain usable or value added products.

Jan 1, 1994

By P. G. McCormick

The refining of rare earth metals by the direct solid state reduction of their respective chlorides during mechanical alloying has been studied. Erbium and gadolinium were synthesised by milling their respective chlorides with calcium. The mechanical alloying of SmC13 with calcium resulted in partial reduction of SmC12. Examination of the milled powders using X- ray diffraction and analytical electron microscopy has enabled characterisation of product structure and morphology. The synthesis of Fe17Nd2 by the mechanical alloying of NdC13 and Fe with calcium has also been studied. The Fe17Nd2 phase forms during heat treatment of the mechanically alloyed powder.

Jan 1, 1992

By G. A. Irona

Solids injection into non-ferrous converters and furnaces is becoming increasingly important for concentrate injection, removal of impurities, and recycling of dusts and other waste materials. The fundamental design aspects of these technologies will be reviewed, including gas and particle trajectories, lance clogging, heat transfer, and mass transfer including reaction rates and mixing. The use of soda ash for removal of impurities such as antimony and selenium will be used as an example of versatility of powder injection processes.

Jan 1, 1993

By J. M. Floyd

Technology in use commercially and available for commercialisation for injection processing of base and precious metals in bath reactors is surveyed and compared. Differences between bath smelting and suspension smelting systems are highlighted in relation to important smelting criteria. The factors affecting the results achievable with various tuyere and lance injection bath smelting systems are discussed in relation to the various smelting, converting and refining operations involved in copper, nickel and precious metal processing steps. Process chemistry, process dynamics and heat and mass transfer rates are discussed for the different systems.

Jan 1, 1993

By M. Shevchenko

Integrated experimental and modelling research program on the phase equilibria and development of thermodynamic databases of the lead and copper metallurgical gas/ slag-matte-metal-solids systems (PbO-“Cu2O”-FeO-Fe2O3- ZnO-CaO-SiO2) is being undertaken to support improvements in the pyrometallurgical smelting and recycling processes. This is the first systematic investigation of phase equilibria of slag systems in equilibrium with Pb metal, providing information for systems in which copper coexists in slag with lead or zinc as major components. The experimental studies involve high-temperature equilibration of synthetic samples, rapid quenching, and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). FactSage-based thermodynamic database development is integrated with experimental research. Initial thermodynamic assessments are used to identify priority compositions and conditions for experiments, which are planned to provide specific data to assist thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved. Continuous database improvement and extension to include new elements are targeted. Example of industrial application is given.

By I. C. Knight

The current levels of copper smelter by-product acid production are reviewed on a regional basis, together with the possible changes in the future. There will be increasing pressure for all smelters to achieve a sulphur capture level of at least 95% by the end of the decade.

Jan 1, 1996

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By Maria Cristina Ruiz

The removal of iron from the leaching circuits is a common problem in the hydrometallurgical processing of non ferrous metals. Among the currently available processes, hematite precipitation is the most recommendable from an environmental point of view. This paper is concerned with the batch precipitation of hematite from ferrous sulfate solutions. One of the main objectives of the study was to determine the effect of the experimental conditions on the extent of iron precipitation as well as the purity and the particle size distribution of the precipitates. The main variables studied were temperature (180 to 220 ºC), concentration of sulfuric acid (1 to 10 gpl), initial iron concentration (1 to 15 gpl) and partial pressure of oxygen (3 to 7 atm). The results showed that increasing the oxygen partial pressure from 3 to 7 atm produced a very small increase on the rate of hematite precipitation indicating that a large partial pressure of oxygen is not needed for an effective ferrous to ferric oxidation. An increase in the temperature produced finer precipitates with lower sulfur contents. On the other hand, an increase in sulfuric acid concentration and initial iron concentration produced precipitates with larger particle sizes and higher sulfur contents.

Jan 1, 2006

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By Kenneth L. Driggs

The 1988 shift in primary smelting facilities from low grade matte (35%) reverberatory furnaces to high grade matte (63%) flash smelting heavily impacted a very stable and successful converter operation. Low matte grade converter campaigns averaged 36,000 short tons of copper and revert production/consumption was in balance. The conversion to high matte grades necessitated oxygen enrichment of converter blast and revisions in operating practices. After two years of operational development, campaign life has risen to over 40,000 short tons and revert production/consumption is again in balance.

Jan 1, 1991

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

By D. L. Jones

The leaching of natural chalcopyrite was studied in both ferric sulfate and ferric chloride solutions. The chemistry of the two reactions is quite different, with substantial sulfur oxidation occurring only in sulfate solutions. Ferric chloride is a more effective reagent, for the leaching rate is greatly increased with finer particles and higher (Fe+++), and unaffected by high (Fe++); none of these advantages are found with ferric sulfate. In addition, the morphology of leaching appears to be different, with ferric sulfate leaching preferentially along fissures or grain boundaries. The kinetics were found to be linear over an extended period, rather than parabolic as reported elsewhere. An explanation of the observed phenanena is proposed using the electrochemical theory of leaching, and experimental measurement of the mixed potential of the mineral during leaching.

Jan 1, 1976

By Junji Shibata

Zeolite synthesized from coal fly ash has many intelligent properties such as cation exchange, adsorption, catalyst and so on. The suitable use of the zeolite, however, is not established in an actual commercial scale yet. From the viewpoints of an effective usage of coal fly ash and the zeolite obtained from coal fly ash, we propose the new concept for environmentally friendly usage of zeolite, in which coal fly ash safely returns to the soil with growing plants and purifying wastewater. This method can make great contribution to recycle of coal fly ash, to purification of high nutritious water and to tree planting.

Jan 1, 2002

By Howard K. Worner

"In a rewarding career spanning nearly two thirds of a century, the author has worked at the frontier of such diverse fields as the creep of metals, structure properties and production of novel dental and surgical materials, molten salt electrolysis for titanium production, greatly improving the productivity of large iron blast furnaces and of oxygen steelmaking. While each of these has given great satisfaction, special thrills have derived from the development of new methods for the continuous production or refining of both ferrous and non ferrous metals. A rewarding segment was the evolution of various aspects of WORCRA technology. Unfortunately, several of these inventions have been ""ahead of their time"". Introduction""I am greatly honoured by the convening of this meeting to recognise my contributions to pyrometallurgy. My appreciation is the greater because this is the third Howard Worner Symposium; the first took place in the University of Newcastle in 1988, close to my 75th birthday. It was arranged by the local branch of The Australasian Institute of Mining and Metallurgy with the theme, ""Frontiers in Pyrometallurgy"". The second was organised by the University of Wollongong in conjunction with the Australian Academy of Science and the Australian Academy of Technological Sciences and Engineering; it celebrated my 80th birthday and, at my request, covered a broad range of topics under the heading of ""Recent Advances in Science and Technology"". Now, this very international meeting on ""Injection in Pyrometallurgy"" has been convened by the G K Williams Co-operative Research Centre for Extractive Metallurgy in my alma mater. I am both delighted and honoured that the cosponsors are the TMS (USA) and ISIJ (Japan).Dr Madhu Nilmani consulted me about the field to be covered and I readily concurred because ""injection"" has been of keen interest to me since the beginning of the 1960s when I began my pioneering work on sequential oxygen (or air) injection into flowing streams for both refining of blast furnace hot metal to steel and for the continuous smelting-converting of copper and nickel."

Jan 1, 1996