Search Documents

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid alumina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scaru;ling electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By George Owusu

A study has been carried out on the use of solvent extraction, instead of the traditional zinc dust cementation process, to remove copper from concentrated zinc sulphate leach solutions. In a series of experiments using plant solution containing 1.9 g/L Cu, 2 g/L Fe, 173 g/L Zn, 7.9 g/L H,SO,, 0.25 g/L Cd, 15 mg/L Co etc. and LIX 622 in SX-1, up to about 97-98 % of copper present in the zinc sulphate leach solution was extracted with negligible co-extractions of zinc, iron, cadmium, cobalt, etc. pH modification was not required for this reagent. The copper loaded organic was almost completely stripped using 150 g/L sulphuric acid. Investigations into the effect of any possible organiclextractant contamination on zinc electrowinning showed (if any) little effect on current efficiency if the organic contamination is less than 45 ppm; current efficiencies of 95-97 % were obtained. At organic contaminations higher than 45 ppm, the current efficiency dropped to about 92- 94 %. Visually, the organic-contaminated cathode sheets had rough surface morphology, becoming more intense with increasing organic concentration, compared to the non-contaminated cathode sheets.

Jan 1, 1998

By David G. Dixon

A mathematical model is derived in dimensionless form which simulates the effluent concentration response of reagents from spent heaps under both fresh and recycled water rinsing. The model is based on dispersion from isochoric pathways distributed in length and cross-section, oriented normal to convection channels in ideal plug flow. The effects of heap height, rinsate flow, and initial reagent concentration are examined. It is shown that the rinsing cycle undergoes a distinct shift between fast and slow rinsing at a certain time depending on the amount of stagnant solution in the heap, and the distribution of dispersion pathways. Results of preliminary column rinsing tests on both agglomerated and unagglomerated ores are presented which partially validate the model.

Jan 1, 1994

By Garg. D.

Premixed bronze powders are widely used to produce a wide variety of P/M components including bearings and bushings by the powder metal industry. The physical and mechanical properties of sintered bronze components such as dimensions, strength, microstructural characteristics, and sintered density are well known to change with sinlering furnace design, particle size distribution in powders, green density, preheating and sinlering time" and temperature, and protective atmosphere flow rate. " However, not much is known about the effect of protective atmosphere composition on physical and mechanical properties of sintered bronze components; This paper describes effects of protective atmosphere composition and sintering temperature on physical and mechanical properties of sintered bronze components

Jan 1, 1996

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid aluimina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scanning electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By Michael B. Tessieri

With the increasing environmental demands and higher fuel efficiency standards on auto manufacturers, the use of aluminum in automotive applications is expected to show significant growth for the balance of this decade. Cast and wrought aluminum usage is reviewed by auto part, and alloy family for the year 2000 automobile. The analysis addresses the effect of this increased volume on the recycling infrastructure and identifies issues and opportunities, which will face the recycling industry.

Jan 1, 1995

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By Liu Chunpeng

Under an inert atmosphere, the temperature enhancement of nickel bearing pyrrhotite irradiated by microwave was measured with a special metal-sheathed thermocouple and the non-isothermal rate equations were obtained. Under the controlled oxygen potential of the reacting gas in the microwave field, over 90% sulfur contained in the pyrrhotite is converted into elemental sulfur directly, the iron and the nickel are transformed into FeO,, NiO, NiFe,O, and FeSiO,. According to the experimental data the rate of the elemental sulfur produced is in diffusional control and the non-isothermal equation derived is

Jan 1, 1993

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating improved technology for mineral flotation. A variable often neglected in flotation control is redox potential. The use of redox control is illustrated by the separation of molybdenite from chalcopyrite. Laboratory testing showed that redox potential had a greater effect on product quality than collector addition. A significant need in froth flotation is greater reliability of the sensors used in measuring and controlling redox potential in mineral slurries. The USBM has developed an automated method for removing scale and reconditioning gold redox-sensing electrodes. Fouled electrodes are anodically polarized to 1.2 V versus the AglAgCI reference potential to remove scale. The electrodes then are conditioned by a brief potentiodynamic treatment to re-establish electrochemical equilibrium. In laboratory tests, this technique removed calcarious deposits from gold electrodes and reconditioned them for useful service in approximately 10 min. In plant practice, this technique would obviate the need for plant operators to manually polish electrodes, and also should result in greater reliability in redox measurements. Inexpensive, automated equipment to condition electrodes in a plant setting is described.

Jan 1, 1995

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Kellie Provazi

"The purpose of this paper is to study metal separation and recovery from a sample composed of a mixture of the spent household batteries main types, using liquid-liquid extraction and metals electroplating. The electrolytes preparation consisted: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution were studied the liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] with tributyl phosphate as extracting agent. After study of solvent extraction and stripping has been recover and separate the metallic ions and with electroplating was recovered the manganese, copper, nickel and cobalt in their metallic forms.IntroductionCurrently has increased the consumption of electronics devices such as mobile phones, laptops, wireless phones, comcorders, etc., especially portable devices that use batteries as a power source, and consequently has increased the disposal of such material.Increased consumption of this devices is caused by several factors including increased popularity of consumer electronics devices, has become essential of modem life. Therefore, recycling of batteries is important because its reduces the waste of raw materias and nonrenewable resouces used in manufacturing these materias and help prevent potential environmental risks associated with improper disposal of these products together with household garbage.The batteries have a very diverse composition, containing metals such as zinc, lithium, nickel, lead, mercury, cobalt, cadmium, iron, copper, manganese and rare earths. Some components may contain hazardous materials such as cadmium, mercury and lead, and can contain acids or bases.This research line is a pioneer in dealing with a single process for recycling a mixture with all batteries types, for only processes that exist in the world are based on the recycling a mixture with all types of batteries, for only processes that exist in the world are based on the recycling of one or two types of batteries [1-4]. This process necessitates the previous separation of the batteries by type."

Jan 1, 2012

By Xue Sun, Dengfu Chen, Yuting Chen, Mujun Long, Song Xu, Helin Fan

In order to seek an effective extraction process for vanadium, the recovery of vanadium from a high Ca/V ratio vanadium slag was studied by sodium roasting and ammonia leaching. In the present paper, the oxidation and leaching process of vanadium slag was investigated by X-ray diffraction (XRD), scanning electron microscopy and energy dispersive X-ray spectrometry (SEM/EDS) techniques. The effects of ammonium carbonate concentration, leaching temperature and leaching time on the leaching ratio of vanadium were discussed. As indicated in the experimental result, the optimal (NH4)2CO3 concentration was 120g/L, leaching temperature was 60°C and leaching time was 20 min. Approximately 92% of the vanadium was recovered under the optimal conditions. Furthermore, by means of X-ray diffraction analysis, the phase transformations of the vanadium slag during roasting and leaching processes were analyzed and discussed.

Jan 1, 2014

By Valery Kaplan

Sulfur emission in the form of SO2 in flue gases is one of the most serious atmospheric pollutants associated with coal combustion and non-ferrous metals production. The carbonate eutectic method for removing SO2 from flue gases at 723–923 K was initially proposed in the 1970s but despite its great efficiency (SO2 concentration in the flue gas after purification reached 0.003 volume %), it could not be implemented by industry due to the complexity of the carbonate melt regeneration stage. Earlier we proposed a method suited to coal-firing power stations where the melt was regenerated using CO as a reducing agent. However, most metallurgical plants do not use coal and therefore lack a large source of CO. Here we propose a method for removing sulfur from the carbonate eutectic melt by purging it with natural gas or a natural gas/air mixture, which are available in the vast majority of metallurgical plants. This reaction leads to the reduction of sulfate to H2S gas that leaves the melt. The experiments we conducted show that nearly complete sulfur removal from the melt is possible at 823 K and that the reaction rate is sufficiently high for a large scale process. One can foresee that this carbonate melt-based SO2 removal technique may become a practical and economically attractive method for limiting sulfur emission to the atmosphere from non-ferrous metallurgical processing plants.

By R. Stefaniuk, T. Le, J-Y Huôt, H. Henein

"One of the most important process variables in gas atomization is the gas to metal (G/M) mass ratio as it has a direct effect on the mean particle size of the atomized powder. If this ratio can be controlled during the atomization process, the powder produced would be more uniform and the d50 more predictable. Thus, atomization using a tundish or gravity feed from a crucible would be more stable. In gas atomization, the gas flow rate can be easily monitored; while it is very difficult to determine the molten metal flow rate. This research paper presents a new method of recording the molten metal height with time using a conducting metal height detector. The metal height recorded in real time during atomization was used to characterize using a model the friction losses in the metal delivery system. It is found that the integrity of the metal delivery tube and the cleanliness of the melt play a key role in the maintaining a stable metal feed.IntroductionIn the gas atomization process, molten metal is normally fed to the system either continuously using a tundish or in most cases a certain amount of metal is melted in a crucible and flows into the atomizing chamber under gravity. In the first case, the metal flow rate is believed to be constant during the atomization process despite the presence of slag or dross on the molten metal surface. In the second case, the amount of molten metal is depleted with time and the rate at which the metal flow decreases with time varies from test to test in a seemingly unpredictable fashion.' Furthermore, most atomization systems are confined units and the metal level in the crucible cannot be detected by a visualization method. In industry as well as in laboratories, the metal flow rate is normally calculated on either the mass of input material or the mass of total production divided by the duration of the test. This figure is not accurate enough and obviously cannot be used as a control parameter for the gas to metal ratio as it is only determined after the completion of an atomization run. The need exists for a metal flow rate measurement and control methodology; thereby the d50 of the powder produced may be estimated and controlled in real time. Clearly, the smaller the variation of the G/M ratio during the atomization process the more uniform the powder produced and hence the size of the particles can be predicted."

Jan 1, 1994

By Chunyang Guan, Jilai Xue, Zengjie Wang, Qiaochu Liu

Molten salts electrolysis method to prepare Al-RE alloys has attracted increasing attention recently. CaCl2 and Na3AlF6 were the most often used melts for this purpose. In this work, Al-Sc alloys prepared by electrolytic deposition process in both CaCl2 and Na3AlF6 melts were investigated, respectively. It was found that Sc distributes almost uniformly and Sc contents increase with increasing current intensity in both melts. Current efficiency was measured for comparison among various current densities applied. The alloy products were analyzed using XRD and SEM, where the formation behaviors of Al-Sc intermetallics were investigated in details. The experimental and theoretical results demonstrate that Al3Sc and Al0.968Sc0.032 are the major precipitates in the Al-Sc alloys prepared by molten electrolysis. The results are useful for selection and optimization of the molten salts compositions and the parameters of electrolysis operation.

Jan 1, 2015

By Sheng-li Wu, Guo-liang Zhang, Bo Su

The mineralogical characteristics of iron ores can influence their high temperature sintering performance. In this study, eight iron ore samples from Brazil, Australia, and South Africa were characterized by their chemical composition, mineral types, particle morphology, and gangue dispersity. Meanwhile the influence rules between the mineralogical characteristics and the high temperature characteristics were evaluated and analyzed. The results showed that the effect of SiO2 on assimilation characteristic of iron ores was relatively complex, Al2O3 and LOI of iron ores had negative correlation with assimilation temperature of iron ores, the dense slab-flaky mineral granule restrained to the assimilation characteristics of iron ores; liquid phase of iron ores with high SiO2 content and low Al2O3 content had high fluidity, and the higher dispersity of gangue minerals in iron ores was good to the fluidity of liquid phase.

Jan 1, 2015

By C. Lupi

The electrorefining of primary copper is a well known technology: in this work copper scrap was directly processed in the same way. he copper and copper alloy scrap was previously pressed by means of a 20 tons apparatus in order to avoid pyrometallurgical operations. The samples obtained in this manner showed a good compactness so that they were used as anodes in the electrorefining tests. The tests were carried out on anodes made by copper scrap, copper alloy scrap and a mixture of the two. The electrorefining tests were performed at both 303 and 333 K, in a perspex cell having a volume of 500 ml using a current density of 250 A/m2. The cathode used was always a sheet of pure copper and the electrolyte composition was 40-50 g/l Cu as CuS04 and 150-200 g/l H2SO4. Current efficiency in the range of 92-97% and specific energy consumption ranging from 0.14- 0.20 kWg of copper were reached in all the tests. The refined copper deposits were analyzed by AAS to verify their purity and observed by SEM to highlight their morphology.

Jan 1, 1998

By Nagy El-Kaddah

"One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100 u. inclusions· are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate the capability of the system for producing super-clean metals.IntroductionThe nature of extraction, refining and processing of metals is such that oxides and other non-metallic particles will always be present. This is due to the highly reactive nature of metals with oxygen and other non-metallic elements. The presence of these type inclusions in metals, even in minute amounts, can seriously flaw the reliability and performance of the final product. They not only reduce the strength and the stiffness of the metal/1/, they are the reason behind many of manufacturing defects such as porosity in castings, surface and internal cracks in continuously cast ingots and rolled products, etc., which act to cause premature failure of manufactured parts. In fact, for critical applications such as turbine blades, there is virtually no tolerance for inclusions above ten microns in size /2/. Therefore, removal of inclusions from the liquid metal is an essential processing step.The demand for cleaner metals has brought major changes in the technology and practice of metal refining and casting. Inclusion removal from the melt is currently achieved by passing the melt through a series of melt treatment systems, including induction stirring furnaces, argon-stirred ladle, and ceramic foam and deep-bed filters /3,4/. These systems are generally capable of removing all inclusion particles above 50 microns in diameter, which meets current cleanliness requirements for most applications. However, they may not be able to meet the projected cleanliness levels for critical applications due to kinetic and operational limitations of these systems in removing smaller particles /5/."

Jan 1, 1996

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988