Search Documents

By S. S. Peng

In recent years many roof falls have been conveniently attributed to the adverse existence of a high horizontal stress. The normal practice of not conducting a follow-up study in a roof fall investigation usually leads to a wrong conclusion. This paper describes two cases of massive oriented roof falls in two separate room and pillar mines. The investigation in each case involved the analysis of past history and current conditions from which remedial measures were recommended and implemented. A follow-up period of up to three years was performed to evaluate the effectiveness of the recommended remedial measures. In both cases, high horizontal stress was proven positively not the cause, contrary to the original conviction of mine management Rather, a weak immediate roof was the basic cause Under a weak immediate roof, a proper roof bolting plan and adequate entry width and intersection span must be strictly observed.

Jan 1, 1999

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coalfields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwall face. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 1, 1999

By Larry Stolarczyk

A clear vision of the future coal mining industry was developed into a hierarchy of technology needs by the National Mining Association (NMA) and the Chief Executive Officers of the mining industry. Although improvements in safety and environmental factors were the main drivers in the technology roadmapping workshop sponsored by the Department of Energy, the agile mining machine of the future must efficiently extract coal from deeper, thinner, and more geologically complex coal beds. One of the challenges will be to develop sensors and software that enable clean coal cutting in a changing geologic environment. The roadmap identifies imaging ahead of raining and horizon control within the top ten needed technologies. For these technologies to be adopted by the mining industry, they must be proven to be effective while driving down mining cost and risk. This paper describes how three-dimensional imaging ahead of mining and horizon sensors enable improved ground control and safety in the mining of underground coal.

Jan 1, 2003

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Bolger Witthaus

"High performance production under challenging geological conditions is a product of several parameters. Main factors are the technical equipment and the knowledge in processing. The design and the support system of maingates must also be taken into consideration. The extraction of seams in German underground hard coal mines of RAG in a range of heights between approximately 1.1 and 4.0 m ( 4 and 13 ft) is done by plow and shearer technology. A complete system for quality management of production is required. The process examination of processes begins with procurement of the equipment. Education and training of the engineers and specialists, as well as for the miners are requirements for success as well.This report gives an overview of RAG measures for achieving high performance. Starting with examination of the processes accompanying procurement of equipment, the following important elements are described. Standards in education and training, technical design and elements of automated processing using stateof- the-art in control systems are critical to this system.The application of automation plays a decisive role in modem coal mines. The latest development in German coal mines is the fully-automated shearer system for longwalls. This helps to enhance safety, particularly in difficult ground conditions, by removing the shearer and shield operators from the immediate mining activity.INTRODUCTIONLongwall mining in carboniferous strata in Germany faces various challenges. Different longwall systems are used to mine up to 24 seams, each with a thickness between 1.1 m (3.6 ft) and 4.0 m (13 ft). High stresses due to a depth of up to 1,400 m (4,593 ft) requiring pillars between the panels, require special systems for roadway development, roadway support and reinforcemen.t as well as for longwall advance operations. Two main types of equipment for extraction are shearer and plow systems. While shearers are utilized for seam thicknesses above approximately 1.8 m (6 ft), plow systems can be used for smaller seam thicknesses between 1.8 m (6 ft) and approximately 1.0 m (3 ft)."

Jan 1, 2010

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999

By Ruixiang Gu

The de-confinement mechanisms of unstable failures as they occur in deep coal mining conditions are investigated using a distinct element numerical modeling code. The Mohr-Coulomb and continuously yielding joint constitutive models were used to study the compressive failures in coal and slip behavior of coal-rock interfaces, respectively. The effect of strength variations within interfaces on the failure mechanism of mining faces is also studied. The stability of interface slip failures was found to have a significant role in the failure mode of coal sidewalls. When the interfaces experience stable slip failures, the sidewalls are more likely to fail in a stable manner. With occurrence of unstable slips at interfaces, unstable compressive failures of sidewalls are triggered. The numerical modeling results support the proposed de-confinement mechanisms and emphasize the importance of including the coal-rock interface behavior in the analyses of unstable compressive failures. The significance of the proposed mechanisms in underground mining conditions is that rock discontinuities with large cohesion drop can become potential factors, inducing unstable compressive failures at ribs and mining faces. Therefore, the de-confinement mechanisms should be taken into consideration in mine design.

Jan 1, 2014

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By Ihsan Berk Tulu

The complex interaction between multiple seam pillar extraction panels and variable topography can generate unexpected ground control problems. This case study describes stress-related damage in multiple seam workings that resulted in difficult operating conditions and compromised the safety of the support crews. The damage appeared to be caused by horizontal stress but the unexpected location of the damage baffled the authors. A 2D Finite element analysis was conducted of the mine layout and surface topography in an attempt to explain the observed failure. It was discovered that the topography resulted in the rotation of the major stress at the location of the current workings. The stress rotation caused asymmetrical interactions between the workings on the different coal beds, which can explain the unexpected response observed in the mine. Consequently the layout of the next panel was changed by locating the vulnerable entry 30 ft away from its originally planned position. The new location was selected to locate the entry in favorable stress conditions. The change in layout resulted in a significant improvement in conditions when the next panel was mined. At the time of writing this paper, a full panel has been developed using the modified layout without undue ground control problems. The case study demonstrates that numerical models can help engineers to interpret and solve complex multi-seam interaction problems.

Jan 1, 2014

By Timothy J. Matthews, Timothy J. Batchler, Ted M. Klemetti

"From 2011–2016, there were 1,511 documented injuries, including 7 fatalities, from ground falls in underground coal mines in the United States. The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in Pittsburgh, PA.The load-displacement characteristics of an 8-ft x 12-ft panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of varying the number and position of the load pull location on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines.INTRODUCTIONThe large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in Pittsburgh, PA."

Jan 1, 2018

By Bruce K. Hebblewhite

This paper provides an overview of the international ?state of the art? with respect to underground coal mining methods used in seams of thickness greater than 4.5 m, through a review of a selection of high performing thick seam mining operations around the world?both Single Pass Longwall (SPL) and Longwall Top Coal Caving (LTCC). The paper discusses the recent operational experiences from these selected faces, together with the ground control issues faced, and identifies some of the major, inherent geotechnical factors that can influence the mining method selection, design criteria, and ultimate performance, from both an operational and safety perspective. It is clear that both of these methods are developing quickly? not only from an operational and equipment perspective, but also from the understanding of critical geotechnical criteria. There is an increasing role for both methods in thick seam environments, although the higher SPL faces will only be successful in the near to mid-term under benign geotechnical environments. Regardless of the method, a thorough understanding of the critical geotechnical factors is a key to successful implementation of either method.

Jan 1, 2013

By D. A. Payne

Large excavations, such as Iongwall panels, result in extensive vertical stress redistribution in the surrounding strata. The large abutment stresses developed may produce damage to pre-existing or planned excavations in the same seam or in seams above and below the workings. Knowledge of the magnitude and location of these stresses is therefore important in the design of mine openings; pillar sizes for panel and pillar layouts, roof supports in longwall gateroads and workings over or above pre-existing or planned extraction in adjacent seams. In an attempt to reduce costs, the Cape Breton Development Corporation (CBDC), a Federal Crown Corporation responsible for operating two retreat longwall coal mines, examined the potential for either interpanel barrier pillar width reduction or entire pillar elimination by the adoption of dual life gateroads for the longwall panels. In order to assess the potential for reduced interpanel barrier widths or total elimination, an investigation of the redistribution of vertical stresses around longwall panels in the Sydney Coalfield was established. The study was conducted jointly by the Cape Breton Coal Research Laboratory (CBCRL), of CANMET (a division of Natural Resources Canada) and the Denver Research Center (DRC) of the United States Bureau of Mines. The program included monitoring of vertical stress changes around longwall panels and gateroad behaviour in two seams. USBM-style hydraulic borehole pressure cells connected to chart recorders for continuous monitoring were deployed at four sites, two at Lingan Colliery and two at Phalen Colliery. This report describes the investigations conducted at Phalen Colliery. Contoured plots of stress redistribution around two sites are presented.

Jan 1, 1995

By David W. Evans

"Induced hydraulic fracture of strata during roof bolt installation is a potentially prevalent, but masked phenomenon within the underground coal industry. Previously reported resin testing programs (McTyer et al., 2014) examined the relationship between resin mixing effectiveness and varying bore hole diameter. The methodology employed within this earlier test program facilitated a further critical area of research – the measurement of back pressures generated within the bore hole during standard rock bolt installation practices. Experimental data has indicated that fluid resin can be pressurised to levels where it exceeds the compressive strength of the strata, inducing hydraulic fracture within the immediate area of the bolting horizon. The routine cycle of roof bolting serves to propagate this effect, progressively fracturing and delaminating the roof during mine advancement. This masked phenomenon can lead to a perception of difficult ground conditions - mining efficiencies and costs are therefore affected, with increased needs for additional support subsequently required to restabilise the inadvertently damaged roof.Further analysis of the parameters associated with resin bolt installation has now been conducted, assisting in the development of an empirical relationship between bore hole pressure, bore hole diameter and bolt insertion times. This relationship has been analysed for 15:1 ratio resins and 2:1 ratioresins, within 28mm and 30mm boreholes. Further to this, load transfer performance has been comparatively assessed for both 28mm and 30mm boreholes, suggesting that for 2:1 resins, acceptable resin mixing and load transfer can be obtained within a 30mm bore hole. The combination of 2:1 resins, utilised within a 30mm bore hole, may well provide the optimal solution to reduce the risk of hydraulic fracture in weaker strata during resin bolt installation.INTRODUCTIONA growing number of industry papers have previously investigated areas of concern associated with the performance of cartridge style resins in roof bolting, predominantly focussing on the effects of plastic film gloving, inadequate resin mixing and the pressurisation of resin within the bore hole. These three effects have a critical influence on the load transfer of the steel bolt element, through the cured resin and into the surrounding strata.Gloving occurs due to the plastic film of the resin cartridge partially encasing or wrapping around the steel roof bolt element – a known phenomenon over many years (Pettibone, 1987). The plastic film creates regions of discontinuity between the bolt, cured resin and borehole, reducing effective load transfer into the strata. Experimentation conducted into the effects of bolt ends fully encased by plastic film (Pastars and MacGregor, 2005) revealed that load transfer can be reduced by 85 to 90% in worstcase occurrences. It is also known that the aggregate filler size used within the resin can assist in shredding and breaking up the plastic film – this effect was observed in a previous study on resin mixing effectiveness (McTyer et al., 2014)."

Jan 1, 2015

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulage ways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Johann van Wjk

Mandatory Codes of Practice to Combat Rock Fall Accidents came into force on South African Collieries in 1997. These were drawn up in accordance with guidelines issued by the Chief Inspector of Mines, The Codes of Practice (CoP's) are legal documents in terms of the South African Mine Health and Safety Act 1996. One of the main results Of the introduction of the COP'S from a practitioner's point of view is that they formalized much of what would have constituted a typical visit to an underground section previously. Other important requirements were as Billows: Support rules and Strata Control Standard Procedures were to be drawn tip. Identification of Special Areas (areas requiring a higher level of rock engineering input and with, typically, higher order of support and restrictions on mining geometries), Changing conditions underground to he identified timeously. Implementation of the CoP to he monitored. To comply with these requirements on Ingwe Collieries (a division of BHPO Billiton Energy Coal) it was decided to produce too separate forms to be used in conjunction with each other. The first of these, the "Underground Section Physical Risk Rating" measures the physical conditions in each section whereas the second form, the "Section Perfomance Rating" determines how well the section personnel are Coping with the conditions. This form also pleasures compliance with the Support Rules and Strata Control Standards. Both forms are essentially risk matrices but with various scenarios described, each with a certain weighting. The "Risk and Performance Form" system for bord and pillar operations has by now been used for five years in the Ingwe and Eyesizwe Mining Collieries and has achieved a great deal of acceptance. This system has enabled the quantification of previously subjective observations and has improved the strata control awareness and management of underground mining sections. Amongst other initiatives it has assisted ill reducing the severity and frequency of fall of-ground accidents.

Jan 1, 2002

By Anton Sroka, Antoni Tajdus, Axel Preusse, Krzysztof Tajdus

"In Europe, the magnitude and range of mining deformation predicted on the surface have been, in most cases, determined using methods based on Gauss' influence function (e.g., Knothe's theory, Ruhrkohle method, Stochastic method). The increase in the application of numerical methods (finite element method FEM, finite difference method FDM, etc.) provides an opportunity to offer a different approach in describing mining deformations. However, this phenomenon is very complex, and due to numerical limitations, a two dimensional analysis was made (in plane strain) in most cases. Such 2D models could not accurately describe the mining geometry and geological conditions. The authors of this paper carried out the calculations in 3D models which describe a mining situation and the character of the strata in one Upper Silesian Polish mine. Furthermore, the authors include some tips for three-dimensional modeling.INTRODUCTIONThrough the years, many numerical models have been used to describe a phenomenon of underground mining exploitation influence on the ground surface. However, such rock masses are highly disturbed (cracks, fractures, changes in water conditions, etc.), and it is very difficult to suitably describe, in a mathematical manner, such materials. Therefore, many of the numerical models created have been corrected in various degrees.At first, models widely used to describe the behavior of strata in the region of exploitation appeared as elastic models, where scientests assumed that a whole strata behaved in a linearly elastic manner, according to Hook's law. Those models have been modifed to received suitable VALUES (of settlement and range of subsidence troughs. Scientests created this amongst others: elastic models with contact between the rocks layers (Shippam, 1975; Salamon, Chugh and Yang, 1993), elastic models with no tension (Chrzanowska-Szostak, 1988), and elastic models with a contact on the subsidence limit plane (Tajdus K., Tajdus A., 2005). However, in most cases, those models did not bring the expected results and the differences between shapes of measured and the calculated subsidence trough were substantial."

Jan 1, 2010

By Ximeng Li

The entries that are subjected to dynamic pressure are much more difficult to maintain due to repeated disturbance. A case study of an entry stress distribution was performed using the FLAC3D program. By analyzing the distribution of stress field around the entries, this paper provides guidelines for entry support design in the lower (#16) seam subjected to the repeated disturbance from longwall mining in the immediate overlying (#17) seam, 72ft (22 m) above. The results showed that there was stress superposition inside the barrier pillar in the lower seam, 15ft (5m) to 45ft (15m) deep, during development. The influence zone of the front abutment pressure in the upper (#16) seam was about 100ft (30m) outby the faceline. The stress-relieved zone was from 0 to 100ft (30m) inby the face. The area further inby the face (i.e., 230 ft (70 m) inby the face) was within the gob compaction zone. Along the face advancing direction, the affected zones of the entries in the lower (#17) seam that were subjected to the dynamic pressure from longwall mining of the immediate overlying seam could be divided into four stages: pillar development stress stage, front abutment pressure stage, unstable gob stage, and stable gob stage. Those entries within an area from 100ft (30m) outby to 100ft (30m) to 230ft (70m) inby the faceline should be reinforced with special supports. The numerical modelling matched the monitoring results well.

Jan 1, 2013