Search Documents

By Boqiang Wu, Ganggang Xu, Xiaodong Wang, Hai Wang, Shibin Zhu

"Using a paste-like slurry as a filling from the ground surface to the goaf, artificial pillars can be built in the cavity goaf to support the goaf roof to prevent roof collapse and ground subsidence. If the accumulation laws of paste-like slurry are known well, the filling technology can be optimized. The laws can establish the foundation for finding out the best methods for building artificial pillars and filling technology. In order to understand the accumulation laws of paste-like slurry in the cavity goaf, Aeolian sand with wide distribution in northwestern China was selected as aggregate, and Portland cement was used as cementitious material to prepare a paste-like slurry. A test model of the cavity goaf was built to simulate the filling process by pump from the ground surface to the goaf to study accumulation laws of the paste-like slurry. The results show that the whole process of expansion and accumulation of the paste-like slurry could be divided into stages: free expansion, fill tightening expansion, and stable expansion. The angle of repose of the accumulation body of the paste-like slurry is constant in the stage of stable expansion, and it is the final angle of repose of the accumulation body. The angle of repose of the accumulation body is highly relevant to the slump of the paste-like slurry, and it is unrelated to the distance between the floor and roof. Under certain conditions of the cavity goaf, reducing the slump of paste-like slurry is one of the effective ways to obtain cost-effective pillars.INTRODUCTIONA large number of cavity goafs of coal mines were left in northwestern China; they were formed in the mining process by room-pillar or strip mining. Safety coal pillars were used to support the roof to keep long-term stability in the goaf, so the ground subsidence was not obvious (Fu, Deng, and Zhang, 2011; Xie, 2014). With gradual weathering, destruction of coal pillars, or additional load from ground surface buildings and structures, there could be a risk of instantaneous collapse of the roof in the goaf. This would affect the safety of existing structures on the ground and adjacent mines (Qu et al., 2017; Li, Xiang, and Jia, 2011; Tan, Guo, and Zhao, 2016; Tan et al., 2017). For disaster prevention of the falling cavity goaf, the current common practice is full filling (Hu et al., 2008; Liu, Zhu, and Huang, 2015; Pan and Wu, 2010). However, for buildings and structures with lower deformation requirements, full filling is excessive. For example, it is acceptable for goaf treatment under general roads and industrial sites to control the maximum deformation and keep the deformation continuous (Liu, 2011; Liu, 2012)."

Jan 1, 2018

By Lou Gaozhong, Guo Wenbing, Zhao Gaobo, Wang Shuren

"The height of a fractured zone due to high-intensity mining (HIM) plays a vital role in the safety analysis of coal mining under bodies of water. This paper described the characteristics of HIM. The processes of overburden failure transfer (OFT) are analyzed. The state of destruction transfers from a certain stratum to the upper stratum as face advance distance increases, and the processes of OFT are divided into two stages: transmission development stage and transmission termination stage. Through theoretical analysis, the limited suspension-distance and limited overhanging distance of each stratum are proposed to judge the damage of each layer. Based on this, the OFT criteria of fractured zone development are obtained. The mechanical model of strata suspended integrity and overhanging stability are established. Finally, a new method to predict the height of fractured zone due to HIM is put forward based on the processes of OFT, the limited suspension-distance, and the limited overhanging distance. Further, a HIM panel in the Datong coal mine is taken as an example. Theoretical methods are proposed, and engineering analogy is used to predict the height of the fractured zone, which is compared with in-situ measurements reported in the literature. The results show that the in-situ measurements for the height of the fractured zone are in close agreement with the theoretical calculation result. Therefore, the rationality and reliability of the theoretical method proposed to predict the height of fractured zone is verified.INTRODUCTIONThe height of the fractured zone (HFZ) due to the exploitation of coal is a key parameter for the safety analysis of coal mining under a body of water (Wenbing, Youfeng, and Hou, 2012). Accordingly, it is necessary to predict HFZ under the corresponding mining conditions before coal mining."

Jan 1, 2018

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By Peng Cao, Jimin Su, Yang Li

"Abutment pressure distribution is different when a longwall panel is passing through the abandoned gateroads in a damaged coal seam. According to the geological conditon of panel E13103 in Cuijiazhai Coal Mine in China theoretical analysis and finite element numerical simulation were used to determine the front pressure distribution characteristics when the longwall face is 70 m, 50 m, 30 m, 20 m, 10 m, and 5 m from the abandoned gateroads. The research results show that the influence range of abutment pressure is 40 m to 45 m outby the face, and the peak value of front abutment pressure is related to the distance between the face and abandoned gateroads. When the distance between the longwall face and abandoned gateroads is reduced from 50 m to 10 m, the front abutment pressure peak value kept increasing.When the distance is 10 m, it has reached the maximum. The peak value is located in 5 to 6 m outby the faceline. When the distance between the longwall face and abandoned gateroads is reduced from10 m to 5 m, the front abutment pressure sharply decreases, the intact coal yields and is even in plastic state. The peak value transfers to the other side of the abandoned gateroads. The research results provide a theoretical basis for determining the advance support distance of two gateroads in the panel and the reinforcement for face stability when the longwall face is passing through the abandoned gateroads.INTRODUCTIONFront abutment pressure is the result of rearrangement of in situ rock stress caused by the mining (removal) of the coal seam. Research on the distribution character of face abutment pressure have significant importance in confirming the width of the coal pillar and the distance of advance support in roadways (Liu et al., 2011; Liu, Jiang, and Zhu, 2015). Currently, there is a lot of research on abutment pressure characteristics of traditional longwall coal faces, thick coal seam longwall faces, isolated faces, and extra wide face abutment pressure distribution (Xie et al., 2006). However, theoretical analysis and research on the distribution law of the fully mechanized coal face to abandoned gateroads are relatively less. Abandoned roadways are often from less mechanized or room and pillar mines. Due to the existence of these roadways pre-longwall mining, the in situ stress has already been redistributed around the roadway (Liu et al., 2007). Thus, when the longwall approaches and mines through the roadway, the abutment pressure distribution behaviour has different characteristics than those of traditional solid undisturbed coal. Especially when the face approaches the abandoned roadway, the understanding of face abutment pressure distribution has significant importance to the timing of support installation (Ren and Ning, 2014). This prevents the occurrence of a roof and rib failure ahead of and on the longwall and highly efficient advance of the longwall safely and productivity. This paper analyses the E13103 face of the Cuijiazhai Mine of Wenzhou Mining Co., Ltd of Kailuan Group, as the engineering case study, and uses FLAC3D numerical simulation software to conduct numerical simulated analysis on the abutment pressure distribution mechanism of longwall coal mining face."

Jan 1, 2018

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By Jun Lu

This paper presents the evaluation, enhancement and comparison of two hydraulic fracturing techniques which were employed to mitigate the impact of a massive sandstone channel on two successive longwall faces. The hydraulic fracturing technique and Longwall Visual Analysis (LVA) software were initially employed to mitigate the impact of thick, massive sandstoneroof during mining of longwall Panel 21. Improved longwall face conditions and productivity were observed as Panel 21 mined through the sandstone channel. However, moderate sandstone fractures and falls at the face were still present in areas where hydraulic fracture influence was not present. Such adverse conditions caused two to three weeks of production delays due to large face cavities, jammed face conveyor and subsequent face gluing. Based on the mining experience in Panel 21, and site-specific roof geology in Panel 22, a modified and more effective hydraulic fracturing program was employed. Fewer well-placed holes were drilled, and larger volume of water was pumped into each hole in order to propagate the individual horizontal pancake fractures over a larger area, thereby enhancing caving and relieving face pressure caused by overhang of the massive sandstone. Longwall Visual Analysis (LVA) software was also employed at Panel 22 to predict the cavity risk index and guide the longwall face crew in double-pulling shields behind the shearer drum. This helped to reduce the tip-to-face distance at the critical spots along the longwall face, which helped mitigate the formation of the roof cavities and failure of massive sandstone onto the face conveyor. Underground observations, face advance rate and face rock delay analysis confirmed that longwall face conditions and advance rate in Panel 22were significantly improved compared to those of Panel 21. Consequently, safety and productivity were improved.

Jan 1, 2014

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Khaled M. Mohamed, Michael M. Murphy, Ted M. Klemetti, Heather E. Lawson

"The design of rib support systems in U.S. coal mines is based primarily on local practices and experience. A better understanding of current rib support practices in U.S. coal mines is crucial for developing a sound engineering rib support design tool.The objective of this paper is to analyze the current practices of rib control in US coal mines. Twenty (20) underground coal mines were studied representing various coal basins, coal seams, geology, loading conditions, and rib control strategies.The key findings are: (1) any rib design guideline or tool should take into account external rib support as well as internal bolting; (2) rib bolts on their own cannot contain rib spall, especially in soft ribs subjected to significant load—external rib control devices such as mesh are required in such cases to contain rib sloughing; (3) the majority of the studied mines follow the overburden depth and entry height thresholds recommended by the Program Information Bulletin (PIB) 11-29; (4) potential rib instability occurred when certain geological features prevailed—these include draw slate and/or bone coal near the rib/roof line, claystone partings, and soft coal bench overlain by rock strata; (5) 47% of the studied rib spall was classified as blocky—this could indicate a high potential of rib hazards; and (6) rib injury rates of the studied mines for the last three years emphasize the need for more rib control management for mines operating at overburden depths between 500 ft and 1,000 ft.IntroductionEfforts to improve the stability of underground mine ribs have continued for decades. These efforts by mining professionals around the world persisted throughout the 1990s and 2000s as well, though much of this work focused on rib support methodology and selection of proper support for a specific location. Despite these efforts, it is unfortunate that there has been a continual occurrence of rib-related fatalities in underground coal mines. While overall improvements in rib safety have been achieved, the average fatality rate is still about 1.3 fatalities per year over the last 18 years (Jones, 2014).To manage and control the rib hazard, rib support is used in U.S. coal mines. The current rib support methods for U.S. mines fall into two main categories: rib control based on intrinsic support systems and those based on external support systems. Intrinsic or rib-bolt support requires a roof bolting machine that can install a bolt fixture into the rib. Furthermore, the appropriate level of support needed to control the ribs with an intrinsic-based support system as well as the design parameters for those support systems for various mine conditions have not been established in U.S. coal mines. Furthermore, surface control systems are often an integral part of these support systems and must be considered in the system design."

Jan 1, 2015

By Andre Cezar Zingano

"The empirical approach for pillar design assumes that geological conditions should be perfect, such as horizontal seams, and that pillar strength and behavior will only depend on the coal seam strength and the vertical pressure caused by the overburden thickness on the coal seam; this vertical pressure is based on the tributary area. Empirical methods do not consider the effect of the interface between the roof and pillar or the floor and pillar.The effect of the interface shear strength on final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 meters). This case study involves a mining section at the 101 coal mine in the Santa Catarina state of Brazil, which is experiencing pillar rib spalling and yielding because of a 1-to 2-cm-thick clay layer at the area of contact between the coal seam and immediate roof. The depth of the coal seam is 60 m on average and 2.3 m in height. This particular section also has 12-14% (7-8°) of seam inclination. The pillar size varies from l lxll to 13xl2m; thus, the safety factor (SF) based on the ARMPS approach is more than 1.5. The objective of this paper is to determine the cause of the pillar yielding and study the effect of the clay layer at the interface between the roof and pillar, including the inclination of the coal seam. This study conducted empirical and numerical models (2D and 3D) to understand the effect of the thin clay layer. The conclusion is that the clay layer affected the strength of the interface between roof and pillar, causing rib spalling and reducing the pillar strength.INTRODUCTIONPillar stability and deformation depends on the coal seam strength and vertical pressure caused by the overburden thickness on the coal seam, and this vertical pressure is based on the tributary area. The effect of the interface shear strength on the final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 m). This interface could be represented by a thin clay layer or an abrupt contact between the coal seam and a rigid sandstone layer of the immediate roof. These two interface conditions are found in the coal mines of Brazil, and the effect of the interface shear strength could increase when the seam's inclination is higher."

Jan 1, 2016

By Anthony (Sam) J. S. Spearing

Backfilling using coal waste is not a novel means for waste disposal throughout the world; yet, backfilling using a high density (paste) backfill is relatively new, except in Germany and Poland. One of the main benefits of a high density backfill, as opposed to a low density (slurry) backfill, is that, if placed at a low permeability and low moisture content, the risk of water table contamination can be relatively low. In addition, if paste backfill can be placed cost effectively, environmental benefits are huge because the surface impoundment footprint can be greatly reduced or even eliminated. This is especially true in room-and-pillar applications. In its current state, backfilling is considerably more costly than surface disposal. This is mainly because paste, as opposed to slurry, significantly increases backfill placement costs; however, this could be offset by increasing the achievable extraction rate. Overall, such a system could potentially improve the public?s image of coal mining in the US for a myriad of reasons. This paper discusses a proposed backfill system for a typical room-and-pillar coal mine in the Illinois Basin of the US and clearly shows the technical advantages, although costs are still higher with fill. The cost differential will likely reduce over time, in favor of the backfill option, as costs of traditional surface disposal increase, due mainly to ever-restrictive disposal regulations.

Jan 1, 2013

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Douglas C. Peters

Part of the ground control research at the U.S. Bureau of Mines is involved with improving ground control data collection and analysis methods. A geographic information system (GIs) is being used within this research effort to standardize the data collected and provide a common graphical and tabular format and analysis system for researchers to access information on underground coal mines. In addition, GIS's can perform relational analyses on multiple map and tabular data sets which are not possible through map-creation or CAD packages or through data bases alone. In addition to standardizing ground control analyses, there is an increasing need for rapid analysis of ground control data in connection with increasing production rates at longwall mines. The examination of a large number of interrelated parameters and their impact on short-term mine safety and productivity under the time constraints imposed by rapid production requires computer-aided techniques. A GIs provides the means to quickly, quantitatively, and reproducibly evaluate mine-wide conditions. This overview of GI8 techniques for mine data integration and analysis, using a mine in Colorado as an example site, will cover the input of data into a GIs, including mine-wide monitoring system data and general data such as roof control plans and geology. The methods to geographically reference these data sets and retrieve and combine them also will be covered. Automation of such processes briefly will be reviewed to allow future users to automate their mine data analyses.

Jan 1, 1990

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By Tony Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and Laurel Hill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereonet, and rose diagram projections so that the Loyalhanna's structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts. pillar sizes, etc., that lessen miner exposure to these hazards.

Jan 1, 2002

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By Elizabeth Holley, Meriel Young, Gabriel Walton

"The coal mine roof rating (CMRR) was developed by Chris Mark and Greg Molinda to bridge the gap between geological variation in underground coal mines and engineering design. The CMRR accounts for the compressive strength of the immediate roof, the shear strength and intensity of any discontinuities present, and the moisture sensitivity of the immediate roof. The CMRR has been widely used and validated in Eastern US coal mines, but it has seen limited application in the Western US.This study focuses on roof behavior at a Western coal mine. Mine A shows significant lateral geological variation, along with localized faulting and a laterally extensive sandstone channel network. The CMRR is not used to predict roof instability at the mine.It is, therefore, hypothesized that there are other factors that are correlated with roof instability in underground coal mines that could potentially also be included in the CMRR.This hypothesis was tested by collecting 30 CMRR measurements at Mine A. At each measurement location, a binary record of the roof condition (stable or unstable) was made along with parameters, such as depth of cover, thought to also correlate with roof stability. A statistical analysis of the data was performed to determine the parameters in addition to those included in the CMRR, which can be correlated to roof stability.INTRODUCTION AND BACKGROUNDRoof fall is one of the greatest hazards facing underground coal miners (Barczak et al., 2000). In 2017, 91 lost-time injuries occurred due to roof fall in US underground coal mines. A further 48 roof falls occurred with no lost days (MSHA, 2018).The coal mine roof rating (CMRR) classification was developed by Molinda and Mark (1994) to quantify the geological description of mine roof into a single value that could indicate mine roof stability and be used in engineering design. It is widely used in the Eastern US as an input for the analysis of longwall pillar stability (ALPS) in underground coal mines. It provides an excellent start; however, it is arguably not fully comprehensive, nor is it widely used in the Western US."

Jan 1, 2018

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013