Search Documents

By James W. Collins

The bucketwheel stacker/reclaimer is suited for a variety of bulk material handling systems, especially those operating with stockpiles in excess of 30,000 tons. The bucketwheel stacker/reclaimer, although relatively new in the United States (first introduced here in 1964), has been successfully used in European countries since the early 1940's. Basically the machine is the outgrowth of the bucketwheel earth excavator and the traveling tripper boom type stacker. Since their introduction here they have achieved wide acceptance, especially with coal fired power plants. (Figures 1, 2, and 3.) The stacker reclaimer has been utilized in barge and ship loading/unloading facilities, and in the material handling systems for steel mills, where it has been used to stack and reclaim iron ore at rates up to 6000 tph stacking and 4000 tph reclaiming. They have also been employed at mine mouth power plants for the handling and storing of the plant fuel supply and to help balance the mining rate with the fuel consumption rate.

Jan 1, 1973

By L. Yuan, J. H. Rowland, R. A. Thomas

"Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners. INTRODUCTION As many types of battery-powered mining equipment such as scoops and shield haulers are used in underground mining operations, charging stations are required to charge the equipment batteries. These batteries are of lead acid chemistry. A safety issue exists with the battery charging stations as all lead acid batteries produce flammable H2 gas during the normal charging process. Overcharging or excessive heat can quickly cause batteries to produce even more H2. If H2 is not appropriately diluted or dispersed, it builds up, and the risk of fire and explosion increases. Mine Safety and Health Administration (MSHA) regulation (30 CFR Part 75.340) requires that battery charging stations should be housed in noncombustible structures or be equipped with a fire suppression system. When a fire suppression system is used, the battery charging stations must be ventilated with intake air that is directed into a return air course or ventilated with intake air that is monitored for CO or smoke using an AMS. The monitoring of intake air ventilating battery charging stations should be done with sensors that are not affected by H2."

Jan 1, 2018

By T. E. Burns

The process engineer is frequently requested to select equipment to separate brine from solids, In many cases, this is a more difficult task than the selection of most other pieces of process equipment because quite often the operation of the various types of debrining equipment cannot be predicted by calculations, One must rely to a great extent upon experience or empirical test work to predict performance - that is to say one must use a practical rather than a theoretical approach. This is not to say that the solutions to liquid-solids separating problems are wholly an art but rather it is to emphasize that the approach demands a fair knowledge of commercially available liquid-solids separating equipment, some background on the advantages and limitations of each type and in many cases might necessitate a fair amount of test work, or at least, a study of performance of equipment on similar applications.

Jan 1, 1966

By Joseph T. Duncan, Syd Peng, Larry G. Stolarczyk

The mining business has numerous risks: equipment availability, labor disruptions, foreign exchange rate, etc., but one of the more important risks is assessing the geology. Improving the “intelligence” of geology can and will have significant positive effect on reducing mining risk and thus enhancing operational and financial performance. The use of the advanced Radio Imaging Method (RIM-IV) on coal seams and ore bodies can create useful two-dimensional (2-D) and three-dimensional (3-D) high-resolution images that provide mining engineers with additional intelligence to better plan and improve operations. Improved operational performance will reduce costs and enable mining companies to meet market and financial commitments. For the past decade the underground coal mining industry has been moving toward “super panels” in long-wall mining, and “super sections” for room-and-pillar mining. These mining conventions employ wider faces, longer gate roads, greater room-and-pillar density, and an increased scale in the amount and complexity of mining equipment. An obvious economy of scale exists: amortization of setup investments over greater volume of coal enables mine management to reduce fixed cost per ton. Restricted by equipment considerations, face widths have currently reached about 1,100 ft. Wider longwall panels are planned, with 1,400-ft widths, but this requires an incremental step in hardware that the original equipment manufacturers will soon bring to market. However, longwall panel length has not yet reached its limits, with some panels planned up to 25,000 ft. While longwall panel length is generally dictated by reserve size and extent, practical restrictions in mine planning also include seam thickness, ventilation requirements, or restrictions involving methane drainage. Super panels have certainly enabled the industry to keep pushing the limits of productivity improvement. However, important considerations in mine planning, now and especially in the future, will be driven in large part by geological factors. While larger developments improve productivity and capture economies of scale, the fact that super panels can contain at least four times the area or coal volume means that the probability of encountering serious anomalies is at least four times greater than with the “conventional” panels. Given the increased probability of encountering anomalies, improved assessment of geology is important for super panels and super sections. Proper due diligence requires a thorough and competent evaluation of a mining property and its ore reserve. Using improved geostatistical techniques is most important, and improving the base data for the analysis is equally important. The old cliché “garbage in, garbage out” certainly applies. Also, the quality of coal reserves is (or has been) declining, so, in the future, mining will be in deeper and most likely thinner seams—and these seams appear to contain greater anomalies that threaten efficient operations. To counter the impact of reserve deterioration, the industry is moving toward greater use of geophysical tools and services. Fortunately, tools such as the Radio Imaging Method™ (RIM-IV) system have been improved and can provide the industry with enhanced 2-D and 3-D images of coal seams and ore bodies. To identify and profile the best areas of a coal reserve, geologists, engineers, and mine managers need greater intelligence in the form of RIM-IV tomographic maps of longwall panels and room-and-pillar sections. These images have enhanced the understanding of in-seam features, which in turn has improved operational plans and performance.

Jan 1, 2005

By A. Palit, M. K. Mohanty

This investigation has concentrated on optimizing the newly developed Pansep linear screen and developing empirical models to predict the screening performance. Most empirical models developed in the past to predict the performance for industrial screens are suitable for the vibratory screens. Understandably, these models are deficient in predicting the performance of linear screens due to the difference in their operating principle. Thus, the main objective of this study has been to develop empirical models suitable for linear screens to predict the partition coefficient for a given size fraction as a function of the aperture size. The inadequacy of the conventional model equation originally developed for vibratory screen has been demonstrated and a modified equation developed to predict the partition coefficient as a function of the normalized mean particle size (d/d50c). In addition, new model equations have been developed for linear screens to predict the screening efficiency as a function of the separation size(d50) and to predict the separation size as a function of the screen aperture. It is believed that these model equations will be useful for the plant operators in selecting the mesh panels of correct aperture size and in predicting the product size distribution based on the selected aperture size.

Jan 1, 2003

By Kaye P. Strong, Desmond M. Levins, Anthony G. Fane

1. INTRODUCTION The safe disposal of tailings is the most important environmental question facing the uranium mining industry today. This is because tailings present a major long term radiological hazard as they contain about 71% of the radioactivity originally in the ore. The magnitude of the problem can be appreciated by considering the quantity of tailings involved. For example, projections of milling programs in Australia indicate that there will be 100 million tonnes of tailings produced by the year 2000 (Levins 1980). The United States currently has in excess of 100 million tonnes and by the year 2000 will have between 900 and 1700 million tonnes (Landa 1980). Present options for tailings rehabilitation include leaving them above ground, returning them to the mine or placing them in specially excavated pits. In any event, the tailings will be covered with earth and revegetation attempted. This will remove the problems of airborne radioactive dust and water erosion of the tailings, at least in the short term, but diffusion of radon-222* from the tailings may still occur. The Atomic Energy Control Board of Canada (1981) has proposed a maximum allowable radon flux from rehabilitated tailings of 0.074-0.37 Bq m -2s-1(2-10 pCi M-2 s-1); the exact level is to be determined "after discussion with other regulatory agencies and the industry". The United States Nuclear Regulatory Commission (USNRC 1980) has been more restrictive in recommending a maximum flux of 0.074 Bq m -2s-1 (2 pCi m-2s-1). As a guideline they also suggested a minimum depth of covering material of 3 m to achieve this surface flux for tailings typically found in the western milling regions of the United States. The design of rehabilitation schemes is aided by a knowledge of radon transport through tailings piles. In this paper we present the results of a theoretical analysis and experimental study of radon diffusion through selected Australian tailings and cover material. The minimum cover criteria of 3 m is reexamined in the light of these findings. [ ]

Jan 1, 1981

ABB Industrial Systems is one of the largest electrical engineering companies in the world. ABB develops, manufactures and markets electric drives. The company has more than 100 years experience in the application of medium- and high-voltage AC machines. And ABB's continuous research and development program ensures that its machines use the latest technologies and materials. Each motor is custom designed to meet specific applications. The HXR high-efficiency motors (100 to 1,900 kW or 134 to 2,250 hp at 50 Hz) are efficient and have low noise levels. Typical applications are pumps, fans, blowers, compressors and pulverizers. The enclosed units are constructed with external cooling ribs and fans. And the motors are equipped with solid, longlife stators and rigid rotor construction. The patented rotor construction provides for low vibration levels. ABB's large synchronous motors (1 to 50 MW or 1,340 to 70,000 hp up to 900 rpm) are used in the mining industry for crushing, grinding hoisting and conveying systems. These motors are designed to customer's specifications, including existing foundations. They can be equipped with fixed or adjustable speed control.

Jan 1, 1998

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By G. Brooker

The back-filling operation at Olympic Dam mine supports a 9.8 million tonne per year (Mtla) underground Longhole Open Stoping operation. It involves a combination of Cemented Aggregate Fill (CAF), Surface Rockfill and Underground Rockfill. The fill material is introduced from the surface via bore-holes into the top of the stopes. Due to the deleterious effects of the dust and the thickness of the atmosphere in the stope it is not possible to view the filling process. The need for a means to measure the filling process is driven by the stopes, which have both rock and CAF fill placed in them. The large volumes and high relative cost of CAF makes the minimization of CAF fill a business priority. Incorrect filling can lead to the sterilization of ore reserve. The use of millimeter wave radar to view through the haze to give real-time data on the relative positions of the different fill masses is being developed as an in-stope fill control device. This paper reviews the salient points of the technology and its potential use in the back-filling operation at Olympic Dam. The broader potential of this technology for use in the mining industry by 'seeing' through water and dust laden environments such as that found in stopes and ore passes is discussed.

Jan 1, 2001

By Y. K. Yen, J. D. Miller, C. L. Lin

Particle size segregation is a common phenomenon in many particulate processes and has many undesirable effects. The size segregation which occurs on a belt conveyor causes a serious problem for on-line particle size measurement using image-based techniques. Whether particle size distributions measured from the top layer of the belt are representative of the total particle population is largely dependent on the degree of size segregation. Therefore, it is important to understand the nature of such size segregation in order to make appropriate corrections for on-line particle size analysis. Monte Carlo simulation has been used to provide segregation information on particles with simple geometry and the results can help to determine important factors in experiments with irregularly shaped particles. It is expected that the relationship between the particle size distribution of the top layer and that of the entire particle population on a belt conveyor can be formulated as a model based function.

Jan 1, 1997

By Nai-piu Tong, Huaren Dou, Sui-shun Poon, Leslie H. Swann

This paper mainly presents geotechnical aspects of a vehicular underpass that was built across under one of the busiest highway in Hong Kong. The underpass, in a section comprising an upper arch and invert slab, is approximately 6.2 m high at crown and 15 m wide at the base level with 40 m in length. The construction inevitably requires the underpass to be built using tunneling techniques to keep the overheadroad traffic uninterrupted. The paper will describe the design of temporary support for the tunnel excavation that was provided by an arch formed with horizontal pipes, which were installed using the pipe ramming method. The pipes arch was then supported by steel ribs founded on rock or mass concrete. Permanent lining design consideration was also discussed. Results of numerical modeling of the soil-structure interaction using the 2-D computer code FLAC will be presented. The predictions have been compared to the monitored results during construction, which indicates the prediction is in reasonable agreement with the measurement in the light of ground movement. The construction challenges will also be discussed in the paper.

Jan 1, 2003

By Norman L. Weiss

The full importance of tailings disposal is yet to be realized by the mining industry, but our awareness of its present and future implications is growing faster, perhaps, than any single phase of ore processing. Few engineers can look very far into the future because of the complexity of the problems that may confront us if we project from the general indifference of past years through what we are already being expected to correct in existing operations, to confrontations with new statutes and an awakened public in any new plants hence- forth. The mistakes of the past have not been limited to the United States nor even to other countries of the Western Hemisphere. Indeed, all continents and subcontinents have suffered from myopia in releasing the tailings without retaining responsibility. However, the US as one of the world's great leaders in technology has a particularly unimpressive record. It may be safely generalized that the degree of control applied to the tailings of a milling operation has depended upon several factors more important than national boundaries. Thus in arid and semiarid climates no incentive was needed other than the scarcity of water to create a permanent and stable lodgment for mill tailings. On the other hand. where water has been plentiful. the temptation to let the tailings run into a river or lake or ocean (at least at certain times of the year) was often irresistible. So we find that modem tailings disposal in the southwest deserts of this country, with one or two notable exceptions where very serious breaks seem to occur at regular intervals, is satisfactory according to the standards of the 195QF and 1960s. while in various operations in Idaho, Michigan, western Colorado. Newfoundland, and elsewhere the record has been less praiseworthy. In the same way, cyanide plants which did not concern themselves about leakage, seepage, spillage, or wastage of tailings pulps with solutions containing toxic levels of free or combined cyanide soon heard a demand for better control. In consequence the industry has seen a growing use of cyanide regeneration of tailings or wash solutions, elimination of leakage, and careful structuring of tailing dams. The chemical and thermal qualities of tailing waters have occasionally been a spur to good tailings management. Some tailings disposal problems for example, the southeastern Florida phosphate clays and the Bayer red muds-have been given the intensive study they merited, but not always with much success.

Jan 1, 1985

By H. J. Marais, P. C. van Aswegen

The Biological Oxidation (BlOX®) Process for the treatment of refractory gold ores was commercialized in 1988. During the last decade, the technology has developed into a mature, commercially viable process, with five additional operations commissioned, including operations at Sao Bento in Brazil, Harbour Lights and Wiluna in Australia, Ashanti in Ghana and Tamboraque in Peru. With ongoing development, the efficiency and cost effectiveness of the process have both improved, making it an attractive alternative to conventional refractory treatment processes such as roasting and pressure oxidation. The bacterial culture is robust and can withstand the normal fluctuations experienced on an operating plant. The plants are simple to operate, making it ideal for remote areas. The scale-up potential of the process has been proven, and it can be applied to large refractory ore bodies. The process is environmentally friendly. Neutralization of plant effluents produces precipitates that comply with the most stringent environmental regulations.

Jan 1, 2000

By Roland Hoet

Mine operators, conveyor system designers, consultants, and manufacturers have had opportunities over the past decade to utilize various actively controlled technologies to drive complex underground conveyor systems. These technologies included several electrical drive solutions, mechanical drive solutions, and hydromechanical (fluid coupling) drive solutions. All of these technologies have their inherent advantages and disadvantages, and only after several years of operation can mine operators fairly evaluate the overall benefits (short term performance and cost vs. longer term operational and maintenance costs) of any particular drive. Far too often in today's world, decisions for new equipment are made with inadequate regard to issues concerning serviceability and maintainability. Many of the newer electrical technologies (primarily AC variable speed drives) which have been used in recent years were selected based on the perceived desirable benefit from variable speed operation. This technology, however, which differs sign8cantly between various manufacturers, is in a constant state of evolution which puts into question the manufacturers' ability for long-term product support. In addition, various forms of this technology have also generated some undesirable operational issues, including reduced motor life, harmonics for the power system, and mine communications problems. This technology is also extremely current-limited, which results in problems handling overload conditions, a frequent occurrence often resulting from a decline in the coal recovery rate (conveying more rock than coal). The fluid coupling, however, is based on a technology which has been used successfully in underground conveyor applications for decades. Although the base hydrodynamic technology is well proven and has inherently beneficial characteristics on conveyor applications, Voith has continuously improved on this technology to meet the increasing demands of today's challenging conveyor haulage systems. Recognizing a need in the market for a reliable, actively controlled drive system, Voith Turbo began development in 1996 of a new, actively controlled coupling which was targeted specifically for the higher powered, complex underground conveyors. Voith introduced the new TPKL Fill Controlled coupling product to the market in 1997, and the first two applications for this new technology were on multiple drive mpper booster applications on longwall panel conveyors. Since the successful startup of these two conveyor systems in 1998, Voith has supplied over 200 TPKL couplings to the mining industry worldwide, with over 150 in US coal mining applications alone. This paper will provide an overview of the TPKL's capabilities, performance, and reliability based on the TPKL's impressive installation base and operational history.

Jan 1, 2004

By A. S. Kane

According to the 1966 Bureau of Mines Mineral Year Book only three states reported production of lignite in that year. These state: were North Dakota, Montana, and South Dakota; although it is known that there is production of lignite in Texas, California and, perhaps, Arkansas. In the year 1966 North Dakota produced 3,543,000 tons of lignite, Montana produced 328,000 tons of lignite, and South Dakota produced 10,000 tons of lignite. In view of the fact that North Dakota produces approximately 95 per cent of all the lignite reported in the United States, in discussing lignite mining, my remarks will be confined to lignite mining as conducted in North Dakota and will be confined to the production of lignite by stripping methods, as this is the predominate method used today. The first lignite mining in Worth Dakota, undoubtedly, was done by people settling in the western part of the state where wood was scarce and where lignite is exposed in the banks of creeks and ravines. The first production records were kept in 1884 and indicate that 35,000 tons of lignite were mined that year. The growth of the lignite industry has been very slow during the intervening period, but in 1966 production started to increase, and it is now indicated that production in the next few years may approach 6,000,000 tons per year. Ninety-seven per cent of the lignite produced in the lignite area of the Midwest is utilized in the generation of electric power, and it is anticipated that this use will predominate during the next two decades.

Jan 1, 1968

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By Anshumali Gangwar

This paper outlines the chance constrained binary integer program developed by the author in his doctoral dissertation at Columbia University, New York, 1973. The optimum planning of a mining program involves the determination of a production schedule which maximizes the net present value of the mining property. The actual mining process has an inherent stochastic and discrete nature. In particular, the demand for the mined product and the grade of the mineralized material in the ore are the two most important stochastic mining variables. The decision to mine or not to mine any block of a mining property is a binary integer variable. This paper outlines the formulation of pit production scheduling problem as a chance constrained binary integer program. The deterministic equivalents of these chance constraints are nonlinear in binary variables which have subsequently been linearized. The planned objective is to meet with a stipulated high degree of reliability, all the random demands as they materialize with a random supply of the commodity being marketed as determined by the eventuating random grade values of the exposed ore blocks and the mining system's production constraints such that the discounted total production costs over the entire planning horizon are minimized or the profits maximized. The emerging surface of the mine in each scheduling period is determined by the values taken by the binary decision variable associated with each block of material in each scheduling period.

Jan 1, 1982

By Y. C. Kim

Three rock fracture parameters define three points along empirical cumulative size (of rock fragments) distribution curves at Inspiration copper mine. These parameters are: rock quality designation (RQD), longest piece of intact rock and % of +1 inch. The RQD and the longest piece are actually measured on drill hole cores whereas % of +1 inch is visually estimated on the same cores. These size distribution curves are then utilized in a variety of engineering applications such as; slope instability analysis, blast design, copper recovery prediction from heap leaching, etc. The three rock fracture parameters for two dominant rock types (porphyry and schist) in the pit had to be estimated separately due to different rock fracture characteristics.' Both ordinary kriging (OK) with measured hard data only and soft kriging (SFTK) with hard and soft data were used to estimate each parameter. The cross validation of 100 measured sample values served as the-basis for evaluating the potential benefits of SFTK over OK. Use of subjective information during SFTK required obtaining (prior) probability distributions for all three rock fracture parameters. These distributions were obtained from the typical rock fracture parameters observed in drill hole cores falling inside the geologically interpreted structural domains with varying degrees. of fracture intensity and also through direct mapping along the exposed bench faces. Two different types of soft information were developed for this study; namely, Type "A" and Type "K". The former is based on sample distribution of fracture parameters whereas the latter is based on two step estimation designed to narrow the range of variation observed in data Type "A". The results of the cross validation were analyzed using a linear regression of actual values versus estimated values. The results confirm an improvement on the estimates made by SFTK with hard and. both types of soft data over those produced by OK with hard data only.

Jan 1, 1989

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016