Search Documents

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

By Richard H. Olson

Talc deposits in the Precambrian of southwestern Montana (Beaverhead and Madison Counties) are unique within the U. S. A. in that large bodies of tremolite-free talc can be open-pit mined. All known deposits are in pre-Beltian dolomite units. The origin is suspected to be metasomatic, with the siliceous component having been contributed by an intrusive Precambrian granite gneiss. Precambrian deformation was extreme and is characterized by multiple periods of tight isoclinal folding and the flowage of less competent rocks, rather than by faulting. Post- Precambrian folding has been relatively negligible; the characteristic Laramide structure is block-faulting developed along northwest-southeast trends. The talc is thought to have been formed in Precambrian time; the high-angle block-faults probably have no significance with regard to the formation of the talc, but do tend to complicate mining operations. Tremolite-free talc ore bodies with horizontal widths of more than 200 feet, vertical depths of several hundreds of feet, and strike-lengths of as much as one-half mile are known in the Ruby Range and the Gravelly Range. Where dolomite is interbedded with tremolite-free talc in the Gravelly Range, the scale of this relationship permits the use of conventional open-pit mining methods with subsequent upgrading by hand-sorting techniques. Underground mining has been used in the past, but all current Montana talc-mining operations are on the surface. The hand-sorted ore, some of which is shipped overseas, is finely ground or micronized in roller mills and fluid-energy mills. The products are distributed both nationwide and abroad.

Jan 1, 1975

By S. C. Tadolini, P. Mills

"INTRODUCTION This research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite with structural strength within a few minutes to prevent parasitic loading and allow ingress into damaged structures within a few minutes of the mix formulation being applied. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was the discovery that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing, as water is added in the form of a mist at the point of delivery; thus low W/C can be achieved. However, as there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. A commercial version of this material is currently offered as Minova’s Tekcrete Fast® product which has been successfully deployed in the mining industry and is currently being used in civil, construction and tunneling operations. The material can rapidly stabilize unstable ground in metal/nonmetal and coal mines. This paper described the technology development, product testing results and applications in mining and civil applications. BACKGROUND The original development of this product was to complete rapid stabilization of shock damaged structures, which falls outside the purview of normal construction and mining practices, due to the critical time issue and the nature of the damaged structure. The stabilization of damaged structures requires materials and equipment that can be rapidly deployed to place materials that have very rapid strength development. These materials need to be placeable at a distance to provide some degree of safety to the responders. In addition, the materials must be able to adhere to structural surfaces that have not been specially prepared and conditioned, and may also be highly fractured, dusty, wet, and quite possibly hot or extremely cold. The technology for the rapid delivery of large volumes of cementitious materials to vertical or even overhead surfaces currently exists. Pneumatic delivery (shotcreting) has been used in construction for over 100 years (American Shotcrete Association, 2014). Shotcreting has played a major role in structures like the Washington D.C. Metro subway system and been used in underground mining applications routinely to serve as part of the primary and secondary support system when used in conjunction with traditional roof bolts. Numerous rapid setting cements are commercially available. They are used for rapid repair of surfaces such as bridge decks, pavements, and commercial floors, as well as structural repairs of vertical and overhead surfaces. Few of these products are specifically marketed for use in shotcrete applications. The majority of rapid setting cements are based on, or at least contain, Portland cement as a principle component. Other components are added that help provide early strength, such as high alumina cement (HAC), organic polymers, chemical accelerators (which can also be added during concrete batching), and calcium sulfate hemihydrate (e.g. gypsum plaster) (Lea, 1971). Cementitious mortars prepared with some of these cements can achieve compressive strengths of 6.8 – 13.8 MPa (1,000-2,000 psi) within 1 hour. However, Portland cement mortar and concrete typically require many weeks of proper curing to reach significant levels of their ultimate strengths, even when used with set accelerators. Also, high early strengths require the use of large proportions of Portland cement in the concrete mix, which can lead to high heat evolutio"

Jan 1, 2017

By H. L. Bourne

The sand dunes which line the east shore of Lake Michigan resulted after the last, or Wisconsin, glacial period in Michigan. Melt-water streams carried vast quantities of glacial debris to the near shore areas of predecessors to Lake Michigan. As the lake levels receded, these vast quantities of sand were exposed to the prevailing westerly winds, which was the last major process that acted upon the sand and resulted in the formation of the dunes. 1 These dunes are one of the significant natural resources within the state. Michigan dune sands supply about 90% of the foundry sand used in the automotive industry, and 40% of the foundry sand used 2 for all purposes within the United States. The deposits owe their importance to the following factors: grain size distribution, grain shape, mineral composition and location with respect to the foundry sand market. In spite of their economic significance these I deposits are in jeopardy through legislative preemption.

Jan 1, 1975

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By Adrian Brown

The primary method of slope stabilization is ground water-control. Recent research has established the properties which slope materials must exhibit in order for stabilization measures to be feasible, but there is little guidance in the literature about suitable field tests to develop the parameters needed for this evaluation. This paper presents a proven method for large scale testing which allows an evaluation of the feasibility of ground water pressure control in a reasonable cost and time frame. Methods of performance and analysis of the test are presented, and the method is illustrated by reference to case examples.

Jan 1, 1984

By Reed S. C. Rogers

The most widely used machines for grinding coal to the sizes prescribed for the pulverized coal firing of furnaces, boilers, and kilns are the vertical ball-race, roller-race and roller-bowl types of mills. However, the increased use of coal has led to an increased use of tumbling ball mills for coal grinding. Specifically, air-swept ball mills are now a part of many dry pulverized coal firing systems, offering the advantages over vertical mills of lower maintenance costs and the ability to handle strong or abrasive (high ash) coals. The current use of wet ball mills is to prepare coal-water slurries for direct combustion, although in time they may also find routine application for preparing slurry feed for coal gasifiers. In either application, wet ball mills ofer the advantages that coal grinding and wetting can be accomplished in a single step, and that the mills are readily used with fine wet screens to assure top size control in the slurry product. The simulation of tumbling ball mills with mathematical models has reached a fairly advanced stage, but the concepts have been applied only recently to coal grinding. As this paper will demonstrate, however, significant progress has been made in the use of models in ball mill circuit design for coal grinding. Included is a description of the techniques used for simulation, recommended parameter estimation methods, and demonstrations of process engineering calculations for large scale coal grinding circuits.

Jan 1, 1986

By Q. Feng

Study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature and curing time, significantly affect the mechanical property of geopolymer matrix. Through optimization, an above 100 MPa compressive strength has been achieved with the geopolymerization products. Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength even after a one month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS and XRD are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method to apply fly ash as a high strength water-resistant precast construction material. INTRODUCTION Geopolymerization is a process of obtaining a polymeric structure from aluminosilicate by dissolving aluminosilicate sources in a strong alkali (NaOH) solution and condensation of free [SiO4] and [AlO4] tetrahedral units (Davidovits, 1985 and 1988; Duxson et al, 2005; Xu et al, 2000, 2002). After being cured at an elevated temperature for a specific time, the geopolymerization product shows a greatly increased compressive strength. Therefore, the product can be used as construction material such as bricks and road pavement. It provides a very promising method to apply aluminosilicate sources such as fly ash as a construction material for a sustainable development. Fly ash is a main industrial waste which needs to be carefully impounded because of its potential impact on environment. Many efforts have been tried to utilize fly ash as construction materials substituting Portland cement because of the following reasons. First, fly ash is a silica/alumina rich aluminosilicate source, which makes the specific material an ideal source for the geopolymerization process. Secondly, the particle size of fly ash is usually very small (< 50 microns) and it saves a lot of energy consumed during the production process of cement for grinding. Thirdly, fly ash is an ideal source for geopolymerization because it is reactive to alkali even at a mild temperature. In the past twenty years, many studies have been carried out on the geopolymerization of fly ash to a make construction material. However, there are some disadvantages associated with the conventional methods of treating fly ash (Palomo et al, 1999; Perera et al, 2007; Temuujin, et al, 2009; Hanjitsuwan et al, 2014). First, in most of the proposed geopolymerization methods, a salient amount of sodium silicate has to be added. It therefore makes it complex whether the achieved mechanical strength of geopolymerization products is due to a real geopolymerization process between fly ash and alkali or just largely the solidification of metal silicate in air at an elevated temperature. Secondly, the authors have noticed that when the geopolymerization product is soaked in water, the solution pH increases sharply and the products will lose its compressive strength gradually in water. Thirdly, the compressive strength of the geopolymerization product as reported is usually less than 50 MPa.

Jan 1, 2019

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By T. Bednarski, T. McCallum

"Physical impurity transfer in solvent extraction (SX) has a significant impact on operating costs, electrowinning (EW) performance, and cathode quality. Some operations use a wash stage to limit impurity transfer by diluting the entrained pregnant leach solution (PLS) to prevent direct transfer to EW. Wash stage operating conditions vary impacting impurity transfer. A number of factors impact dilution efficiency including mixer continuity, wash aqueous acidity, and organic quality. The impact of these variables on dilution efficiency was studied and compared to current industry practice. INTRODUCTION With the exception of iron, impurity transfer in copper SX is due to PLS carryover in the loaded organic via aqueous entrainment and crud movement. The quantity of impurity transfer is influenced by many variables including operating set points, organic quality, and settler housekeeping. Crud management and treatment is a common practice aimed at minimizing transfer of impurities to EW. Crud is a complex solid-stabilized emulsion of aqueous and organic[9]. As such, it contains a large aqueous component and the associated impurities (from the PLS). A common practice is to remove interfacial crud to prevent movement. Additionally, mixer continuity can be altered to enable compaction and improve the efficiency of interfacial pumping[10]. Understanding the factors impacting aqueous entrainment and optimizing the available controls should be a key focus for any operation. Aqueous entrainment in the loaded organic can be impacted by: • Mixer continuity • Mixer organic/aqueous (O/A) ratio • Mixer speed and impeller type • Organic and aqueous depths • Specific settler flow • Use of settler internals (picket fences, coalescing packs) • Organic quality • Design and operation of loaded organic tanks Conventional thought is to run the E1 mixer in aqueous continuity to reduce aqueous entrainment. Generally, O/A ratios close to 1:1 result in improved metallurgical and physical performance. Mixer speeds should be chosen to achieve acceptable stage efficiencies while minimizing over-mixing. Organic depths can be increased in the E1 stage to increase retention time and minimize aqueous entrainment. Settler internals can also be used, but require maintenance to maintain effectiveness. The quality of the plant organic inventory will impact physical performance. Poor organic quality can lead to higher phase disengagement times increasing impurity transfer to the electrolyte. Additionally, the design and operation of the loaded organic tank can impact impurity transfer[8]. Despite the variables that can be used to reduce aqueous entrainment and crud movement, impurity transfer is still an issue in some operations. For these operations with high PLS impurity concentrations, a wash stage may be beneficial to manage impurity transfer. Understanding factors impacting wash stage performance is important to optimize performance and limit impurity transfer."

Jan 1, 2016

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry&apos;s supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations&apos; average Cost of capital.

Jan 1, 1969

The purpose of the 3DOPT Program is to determine, starting from drill hole data, the optimum economic mining limits for an open pit. The economic limits are defined as those which maximize total profit, i. e. total mineral value mined less the total mining and milling costs, subject to the restriction imposed by the pit slopes. To accomplish this, the program employs the following: (1) A three dimensional matrix of equal sized blocks in order to file the engineering data and the cost/value data required to develop the profit figure for each block of ore/waste. (2) A graph algorithm developed specifically for optimizing these profits.1

Jan 1, 1966

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

By Wilbur C. (Original by) Helt

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation&apos;s most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal&apos;s use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being-looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals.

Jan 1, 1981

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991

By Ren Bryce

The ninth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the SME Annual Conference & Expo in Minneapolis, MN. A total of 33 students presented their work at the contest. The competition began in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes. The students worked hard at their research and then set aside time to complete all the necessary steps to enter the contest. The MPD recognizes the effort required to enter and, as a result, provides monetary rewards to all participants. As in past years, there are separate levels of competition for undergraduates and graduates, and the prizes are designated accordingly. At the graduate level, first place receives $1,000, second place $500, third through seventh $200 each, and all others $125 each. At the undergraduate level, first place receives $1,000, second place $500, third place $250, and all others $125 each.

By William F. Hahn

It is a pleasure to speak to this group about special crusher installations which are in the bauxite and phosphate rock processing industries. The installations to be discussed demonstrate the variety of conditions, materials, and results desired which must be evaluated before a selection is made from the specialized crusher technology available today. Those of you who are closely involved with phosphate rock and phosphate products processing will find some of this information a bit interesting and perhaps alien to your own descriptions or every day references. It is given from a "crusher" manufacturer&apos;s viewpoint and therefore is infused With our flair and language. General features of six (6) different crushers will be shown in cross-section With slides and will be discussed in the same order.

Jan 1, 1978

By M. S. Klima

Proper analysis of washability data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Jan 1, 1997