Search Documents

By R. L. Grayson, S. S. Peng

Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include: 1. Respirable mass concentration, 2. Mineral composition, 3. Particle size distribution by mineral, 4. Particle shape distribution by mineral, 5. Particle angularity distribution by mineral, and 6. Respirable size distribution. Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.

Jan 1, 1986

By Frederick T. Graybeal

Silver Bell is located about 56 km (35 miles) northwest of Tucson, AZ. It is a classic porphyry copper deposit containing enriched disseminated chalcocite ore in altered porphyritic rocks with chalcopyrite in adjacent skarn zones. The discovery of Silver Bell was an evolutionary process that occurred over a 75-year period. Recorded mining activity began about 1865 on Boot Hill east of El Tiro pit (see Fig. 1) where outcrops of altered limestones were found to contain 425 to 482 g (15 to 17 oz) Ag mixed with copper oxides. By 1874, the Young America Copper Co. was mining shallow occurrences of 30% Cu along the north side of the present Oxide pit. The ore was shipped by wagon to Yuma, AZ, and then by boat to San Francisco for smelting. By 1881, the district supported several mining companies, two small smelters, and was being favorably compared to Bisbee in local newspapers. Most of the ore mined in the period 1865-1903 came from pods of massive sulfide or their oxidized products which were distributed in an unpredictable fashion through a large skarn zone in Paleozoic limestone east of El Tiro pit. Ore grades varied from 5 to 10% Cu.

Jan 1, 1991

By G. D. Hood, B. E. Davis

A problem that has continued to plague the Florida phosphate industry is loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µm) in a separate circuit have resulted in limited success, but recovery is still not optimum. A fundamental examination of the mechanisms involved in the conditioning of the coarse phosphate has led to results that seem to supersede common paradigms. The Bureau of Mines investigated conditioning parameters such as fatty acid/fuel oil dosage, residual clay content in the feed, conditioning time, mixing intensity, and conditioner solids content. The study revealed that the effect of all these parameters was important. However, it was discovered that contrary to common beliefs, the conditioning time affected the grade of the rougher concentrate much more than the recovery. Specifically, the longer the conditioning time, the less quartz that was floated. It was also discovered that high mixing intensity conditioners could lower the conditioning time required for good grade. Many phosphate operators use low intensity drum type conditioners. Optimizing the conditioning time, mixing intensity, and other conditioning parameters resulted in a rougher concentrate grading 30 pct P.2O5, with an attendant recovery of 95 pct.

Jan 1, 1993

By E. William Rossi, Audrey F. Glowacki, Richard L. Unger

The U.S. Bureau of Mines has developed a graphics-based computer model to assess operator visibility for continuous miners, shuttle cars, and scoops. Using digitized drawings of the machine, the program can analyze visibility for both 5th percentile female and 95th percentile male operators. This model was used to predict 95th percentile male operator visibility for two shuttle car designs. These results were then compared to those obtained from a manual assessment of visibility using the actual shuttle cars. The methods showed good correlation except for several cases which were attributed to imprecise digitization of the machines.

Jan 1, 1992

By J. Kallioinen

The paper describes industrial size experiments with a 100 m3 flotation cell validating the Size Specific Flotation concept and the Tank Cell design. It discusses some variables affecting the flotation of coarse particles. The results were good. The flotation recovery of coarse particles increased up to 50%. In finer sizes the flotation improvement was 5-15% The enhanced flotation of especially the coarsest particles increased the total recovery close to 10%-units compared to conventional cells in a porphyry copper flotation. The related power draw was only 50-80% of the power of conventional cells.

Jan 1, 1995

A study was undertaken to determine the effects of five industrial frothers on the relationship between entrainment recovery and water recovery. The experiments were conducted using a Batequip rectangular 60L steel flotation cell that was run in parallel with the first cell in a copper/silver prefloat rougher circuit. The concentration of the frothers ranged from 2.5 to 8.4 g/t. The experiments were repeated at three different froth depths. A power function was found to fit this relationship with no discontinuity in the relationship caused by the changes in frother type and concentration and froth depth.

Jan 1, 2002

The American Mining Congress International Coal Show, this year’s largest gathering of coal industry leaders, convened May 5-8 in Chicago. Against a 73 000-m2 backdrop of the coal industry’s most productive equipment,* some 23 000 people heard government and industry executives give guardedly optimistic reports of coal’s near future gains. Although a rocky road lies ahead, operators and suppliers still continue their search to improve efficiency. Among the ideas discussed at the show were better underground communications systems, continuous on-line coal analysis, and recovery of hard-to-float coal.

Jan 7, 1980

By G. A. Hazen, S. M. Sargand

This study monitored longwall mining subsidence profiles over three panels that were mined beneath state highways in southeastern Ohio. The average maximum subsidence was 1.07 m (3.5 ft). The average maximum compressive strain recorded was 0.008 mm/mm. Three predictive methods for the determination of displacements and strains were compared: the National Coal Board (NCB) graphical method, the profile method with empirical constants determined for southeastern Ohio, and a finite element excavation program. Excellent subsidence agreement was found with the profile method, and reasonable strain agreement was determined with the finite element program.

Jan 1, 1987

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By E. A. Laurila

During last years many different types of X-ray fluorescence analysers have appeared in the market most of these instruments being designed for laboratory use. The instruments applied ins continuous processes are usually modifications of these laboratory types. The application of these instruments to the analysis of heavier elements seems to be quite satisfactory. By lighter elements difficulties are caused by the strong absorption of the characteristic fluorescence radiation, which sometimes makes the use of vacuum or helium chambers necessary. In the following an instrument of another type will be described. It has been developed exclusively for the analysis of titanium in ilmenite concentrate, where the content of Ti02 varies between 43 - 46%. Preliminary measurements have shown that in this interval absolute change of 1% in the Ti02 concentration causes a relative change of about 2% in the intensity. Because: the accuracy of 0.5 % Ti02 is sufficient, 1% relative accuracy should be, attained in intensity measurement. The problem is not very easy to solve due to the fact that Ti K radiation is rather soft and the requirement's for accuracy are rather high. Being applied to the analysis during a continuous process may statistically fluctuating variables in connection of sampling and disturbances of many kind set special requirements for the instrument design.

Jan 1, 1960

By L. G. Wilson

In our comparison of California and Turkish colemanites, we should first place the discussion in context. In order to exclude technical considerations, which are not germane to this paper, we must make the manifest and basic observation that if colemanite were not acceptable for the production of glass products it would not be used, and we would not be interested in this comparison at all. Suffice it to say that the colemanites, being calcium borates, provide a necessary flux in glass manu¬facture, together with the requisite degree of physical strength and chemical durability which can be achieved only by the use in glass of a. flux substanti¬ally free from alkali; so the sodium borates are automatically excluded from the production of textile fibers. Thus we have today under consideration only California colemanite, Turkish cole mite, and, because it provides a degree of competition to both, ABA, or anhy¬drous boric acid, which, although it is a refined intermediate and of much higher cost, it is also of a much higher degree of purity, and its characteristics can easily be modified to produce a desired end product, so we must include it in any consideration of high quality borates. [Calcim Borate Pentahydrate] Colemanite is a [calcium pentahydrate,] with the formula Ca2B6011.5H20. It has a theoretical B203 content of 50.8%.

Jan 1, 1973

By Keith G. Wallace, Gary K. Rogers

As a supplement to an analysis involving methodologies for the estimation of airflow resistance in shafts used for both ventilation and hoisting, a detailed shaft characterization survey was distributed worldwide. The survey provided detailed information which enabled verification of recommended velocities and established limitations on fill factors and relative velocities. This paper evaluates the information obtained for 37 shafts and presents a statistical evaluation of the results. Apart from airflow rates, conveyance rates, and physical characteristics, qualitative information regarding means of conveyance stability and velocity control techniques at unloading and loading points are also presented. Calculations of fill coefficient, free area velocity, and most importantly, relative velocity between the airflow and hoist, are conducted. These results are presented by frequency diagrams which illustrate the trends, as well as provide limitations for these parameters. The data illustrates that, commonly, the fill coefficient for two or more conveyances, does not exceed 30 %. A limit of 50% is suggested for a single conveyance shaft. A recommended free area velocity of 10 m/s (1,970 ft/min) for combined ventilation and hoisting shafts, is sup- ported by these results. Relative velocities of 30 m/s (5,905 ft/min) are most frequent and 50 m/s (9,840 ft/min) being a practical maximum.

Jan 1, 1987

By Syd S. Peng

The key design parameters of roof bolting using expansion - shell type support for underground coal mine roof support are bolt length, bolt spacing, installed load and anchorage capacity. Depending on the utilization of suspension effect or friction effect, the bolt length is dictated either by the distance between the roof surface and the first overlying strong strata encountered or the desired magnitude of reduction in bending stress at the roof surface, The current prevailing practices about the bolt spacing and installed load are that an initial torque of 125 - 170 ft-lbs is applied and the bolts are spaced at 4- or 5- ft. square grid pattern. This seems to be a rather broad generalization in view of the great geological variances which are expected in underground coal mines. A modest evaluation program to measure the effectiveness of current roof bolting practices is to monitor the load history of roof bolts during a complete mining cycle including the phases of room development and pillar robbing. The load history, when compared with the anchorage capacity of roof bolts determined by in-situ pull tests, will provide information for evaluating the installed load, the bolt spacing as well as the specifications for structural and anchorage characteristics of the bolt assemblies. This paper presents a case history of monitoring the complete load histories of roof bolts in an underground coal mine of Pittsburgh seam.

Jan 1, 1976

By James A. Strosnider

INTRODUCTION The Metro Rail Project is approximately a 20-mile initial portion of Southern California's planned 150-mile transit network and will provide transit service to the dense population and employment centers within the Los Angeles regional core. The Southern California Rapid Transit District (SCRTD) has defined, as the first segment, a 4.4-mile five station rail line, which extends from the yard and shop area near Union Station to the Wilshire/Alvarado Station. Design packages are completed; utilities are currently being relocated; demolition is underway; early construction contracts have been awarded; and construction has started. This paper will describe the current status of the Metro Rail design and construction, after first briefly reviewing its history, objectives, and main components. PROJECT HISTORY The California State Legislature created the SCRTD in 1964 with a legislative mandate to design, construct, and operate a rapid transit system within the Los Angeles County area. To obtain the monies required to support this program, in June, 1974, Proposition 5 was passed by a solid majority, allowing a portion of state gasoline taxes to be used for rapid transit development. This measure provided a local source of funds for SCRTD to begin its rail rapid transit development program in Los Angeles.

Jan 1, 1987

By G. M. Molinda

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

Jan 1, 2008

By David M. Sullivan

Jim Walter Resources, Inc., (JWR) a division of Jim Walter Corporation, has 5 underground coal mines in Central Alabama varying in depths from 400-2500 feet. Gas Chromatography plays a vital role in safety and production at each mine. Chromatographic data is used to monitor working areas for safety and proper ventilation and to control the quality of extracted methane for sales purposes. Instruments have a1 so been employed during mine rescue operations. JWR's first Gas Chromatograph (GC) was installed in April 1984 to monitor gob gas taken from longwall gob areas and sold based upon BTU value. The GC allows maximum extraction rate of the gas within the quality guidelines. By late 1985, another system was purchased and both units were upgraded to perform an analysis of indicator gases which may appear during mine emergencies. Each unit has the ability to detect and measure the following gases at almost any level ; Oxygen (021, Nitrogen (N2), Methane (CH4), Carbon Dioxide (C02), Hydrogen (HZ), Carbon Monoxide (CO) , Ethylene (C2H4), Ethane (C2H61, Acetylene (C2H2) and a composite of hydrocarbon threes and above (C3+). The analytical run is accomplished in less than ten minutes and is completely automated. This report will introduce Gas Chromatography as applied by Jim Walter Resources for the analysis of underground mine air.

Jan 1, 1987

By C. P. Lazzara, F. J. Perzak, C. C. Hwang, C. D. Litton

Fire development and spread along conveyor belts in ventilated ducts were investigated experimentally and theoretically. Various types of conveyor belts used in mining applications were ignited and burned in a full-scale gallery under various flow conditions. The flame spread rates depended strongly on the ventilation air speed. The time-temperature traces of gas and belt obtained at 12 feet from the entrance show that a rapid belt surface temperature change takes place prior to a change in the gas temperature, indicating that radiative heat transfer from the flame to the belt surface plays an important role. Further, anomalies in the flame spread rate in the vicinity of 1.5 m/s air speed (i.e., much greater rate than that observed at either higher or lower speeds) can be explained through the mechanism of flame tilt and the resultant view factor between the flame surface and the belt surface. In order to correlate the fire spread with material properties of the conveyor belts (such as the specific heat, the thermal conductivity, and the pyrolysis temperature) and the fire environment (such as the gas temperature and the ventilation air speed), a theoretical model has been developed. This model is based on the experimental observation that the radiative heat transfer is the dominant mode of energy transfer ahead of the flame front. Agreement between the theory and the experimental results is good.

Jan 1, 1991

By G. Sanders

The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominant-lithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below.

Jan 1, 1993

By G. J. Hartman

The Fort Cady in situ borate mining project involves recovery of boron from a mineral deposit located over 1400 feet below the surface. The resource recovery method is being developed using in situ mining technology employing weak acid solution injected directly into the ore body. As the acid contacts the calcium based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by use of submersible pumps. At the surface the borate values are recovered as a finely divided solid white powder after a series of chemical reactions and precipitations resulting in the production of calcium borate. The refined product is then sold under the trade name CADYCAL 100.TM All environmental permits for up to a production rate of 90,000 tons per year have been obtained. These permits required an Environmental Impact study (EIS) for federal lands and an Environmental Impact Report (EIR) for the private portion of the property. Regulatory permitting required over 5 years to obtain all the various authorizations for this project. The ore body has an average thickness of 118 feet extending over 273 acres. At a production rate of 90,000 tons per year with only a 70 percent resource recovery allowance, in place reserves are sufficient to sustain production for over one hundred years.

Jan 1, 1997

By G. J. Hartman

The Fort Cady in situ borate mining project involves recovery of boron from a mineral deposit located over 1400 feet below the surface. The resource recovery method is being developed using in situ mining technology employing weak acid solution injected directly into the ore body. As the acid contacts the calcium based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by use of submersible pumps. At the surface the borate values are recovered as a finely divided solid white powder after a series of chemical reactions and precipitations resulting in the production of calcium borate. The refined product is then sold under the trade name CADYCAL 100.TM All environmental permits for up to a production rate of 90,000 tons per year have now been obtained. These permits required an Environmental Impact Study (EIS) for federal lands and an Environmental Impact Report (EIR) for the private portion of the property. Regulatory permitting took over 5 years to obtain all authorizations for this operation. The ore body has an average thickness of 118 feet extending over 273 acres. At a production rate of 90,000 tons per year with only a 70 percent resource recovery allowance, in place reserves are sufficient to sustain production for over one hundred years.

Jan 1, 1997