Search Documents

By I. de Jong, G. Van Weert

Silver cyanide adsorbs extremely well on activated carbons. This suggests that the addition of soluble silver salts to trace cyanide containing waste streams should allow efficient cyanide removal with active carbon. Silver losses, however, would make this method expensive and also objectionable, since silver has biocidal effects. When silver impregnated carbon is used, these problems are overcome. Test work has shown that such silver remains on or in the active carbon, that cyanide concentrations can be reduced to the level of detection (< 5 ppb) and that the silver impregnated carbon can be reactivated with equipment similar to that now in use at gold milling operations. Initial results on the type of carbon, the impregnation procedure and the level of silver, and the effect of repeated regeneration are discussed.

Jan 1, 1992

By P. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The feasibility of recovering cyanide and copper from a gold mill barren solution was evaluated in a small A VR pilot plant. The campaign lasted 64 hours, during which time about 4,000 L of gold mill barren solution were processed. The results showed that A VR is an effective technology for recovering cyanide and copper from barren solutions. Under the best conditions, the copper precipitation and the cyanide volatilization attained 94% and 98%, respectively. Using 5 MNaOH as the absorbent, practically all the HCN gas was recovered in the form of a concentrated NaCN solution containing 70 g/L free CN. Basic engineering design parameters applicable to a large-scale operation were obtained, including the Henry's Law constant and the mass transfer coefficient for HCN gas.

Jan 1, 1997

By Harold Wahlborg, George Owusu

In a study using butyl diglyme as an organic extractant, essen­tially complete extraction of gold from chloride leach solution was achieved. The extraction kinetics are so fast that the process could be completed in 30 seconds. Except for iron, co-extraction of other ionic species was insignificant. Co-extracted iron species were successfully scrubbed from the loaded organic using 10% HCl solution. High grade, >99.9%, gold was recov­ered from the loaded organic using 5% oxalic acid solution as the stripping agent at a temperature of 70°C to 80°C. Over 99% of the organic-loaded gold was stripped from the organic phase. The butyl diglyme extractant is being tested on a variety of gold-bearing feedstocks. Presented here are results obtained from two gravity concentrates.

Jan 1, 1999

By Robert Roggenthen

In 1994, ASARCO&apos;s Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By Konstantinos Komnitsas, Evangelos Petrakis, Emmanouil Varouchakis

The paper discusses the limitations of population balance modeling (PBM) in predicting particle size distribution in grinding systems. It introduces a nonlinear framework that transforms the batch grinding equation into the Rosin-Rammler distribution, providing more accurate analysis under different operating conditions. The study uses marble as test material and investigates the adaptability of the nonlinear model with different media sizes.

Oct 1, 2023

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By Herman Gill, Dani Delaloye, Madelyn Rubin

The Foothill Tunnel is a remote 16-mile-long untreated drinking water tunnel in the San Francisco Public Utilities Commission’s (SFPUC) Hetch Hetchy Water and Power (HHWP) system. The 14-foot horseshoe shaped tunnel, constructed in the 1920s, is lined intermittently with concrete over approximately 53% of its length, with the balance being unlined rock. After detailed planning, in January of 2020 Mott MacDonald and HHWP staff completed a visual inspection and documented the condition of the tunnel with electronic data collection, photographs, and video with audio recording. The result was a comprehensive condition assessment that identified key areas of the tunnel to monitor.

Jun 13, 2021

By JIAQI JIN, Chen-Luh Lin, Amanda N. Erskine, Jan D. Miller, Shijie Wang

The liberation and exposure of valuable mineral grains in ore particles are of significant importance in understanding the efficiency of flotation separations. A flotation feed sample from the Kensington concentrator was scanned by micro Xray computed tomography (micro-XCT), to determine the liberation and exposure of auriferous pyrite grains. The analysis results suggest a satisfying extent of liberation for particle sizes smaller than 212 μm. Theoretical flotation recovery of pyrite for selected particle size fractions was predicted from the three-dimensional liberation and exposure analysis. The plant flotation tail was also characterized by micro-XCT to identify liberated and partially liberated pyrite particles that might not be collected into the concentrate. However, liberation analysis of the tail sample revealed that the majority of liberated pyrite was recovered in the plant flotation circuit. Trainable Weka, a machine learning segmentation approach, was compared with the Watershed thresholding segmentation for the 106 × 45 μm particle size fraction scanned at a voxel size of 1.85 μm. Improved segmentation of small particles was found using the machine learning method.

Mar 1, 2024

By Fred N. Kissell, George H. Jr. Schnakenberg

INTRODUCTION A variety of instruments are available for measuring or monitoring the performance of underground mine-ventilation systems. In general terms, the instruments may be classified as those that measure air velocity and those that measure gaseous concentrations. All costs herein are in terms of 1978 US dollars. The mention of a specific manufacturer or device is not intended to be an endorsement by the US Bureau of Mines. AIR-VELOCITY INSTRUMENTS The basic instruments used for measuring the air velocity in mines are the vane anemometer and the smoke tube. Vane Anemometer Of the air-velocity instruments, the 102-mm (4.0¬in.) vane anemometer is the most common and is available as either a low- or high-speed type. The low-speed anemometer generally is the most suitable for measuring the velocities in ordinary airways. For a rough check of the velocity in an airway, it usually is satisfactory to hold the anemometer by hand, positioning it in the center of the airway for 30 sec. However, the resultant error may be as high as 25% , and such a hand-held approach is unsuitable when accurate or reliable measurements are required. To obtain more accurate measurements, the proper procedure is as follows: 1) Since holding the anemometer by hand generally causes the instrument to read about 15% high, it is mounted on a 0.6-m (2-ft) extension rod. 2) The airway is divided into equal right and left halves. A 1-min traverse is used in each half, moving the anemometer smoothly up and down in a zigzag pattern so that the entire half is covered within the allotted minute. 3) The manufacturer&apos;s correction table is applied to the readings to adjust the velocity calculation as necessary. Whenever possible, anemometer readings should be obtained in a long straight section of airway that has a constant cross-sectional area. Bends and obstructions should be avoided, since they cause turbulence and other discontinuities in the airflow and can degrade the accuracy of the velocity measurements. Although a series of velocity measurements at one location usually corresponds to within a few percent, this is not an indication that the airflows calculated from those readings are completely accurate. One reason is that the correction table provided with the instrument generally is not for that specific instrument; instead, it represents the average correction for all such instru¬ments made by the particular manufacturer. Most cor¬rection tables specify a correction factor of from 0 to 15%, depending upon the velocity. However, even after correction, the instrument error still may range from 3 to 5%. At low velocities such as those below 0.76 m/s (150 fpm), the instrument error can be two or three times greater than this, ranging from 6 to 15%. The new ball-bearing anemometers generally perform somewhat better at low velocities than did the older conventional anemometers. Another source of error is introduced when measur¬ing the cross-sectional area of the airway or entry. Under the best of circumstances, measurement errors, instrument errors, and a host of other minor errors all combine to cause a total error of at least 10% in the velocity calculation. The vane anemometer also can be used with reason¬able accuracy to measure airflows in mine-ventilation ducts. In this application, the anemometer is mounted on a rod and is held at the center of the duct end. For a duct that is discharging air, the average velocity in the duct is 85% of the centerline reading (Northover, 1957). For a duct that is taking in air, the average velocity is 70% of the centerline reading (Haney and Hlavsa, 1976). To measure the airflow discharged from a regulator or from a small hole in a stopping or bulk¬head, a correction factor for the area is necessary. A good approach in this situation is to traverse the area of the regulator or hole, holding the anemometer with an extension rod. This provides an average velocity that is multiplied by 85% of the measured area of the regulator or hole. In all cases, the manufacturer&apos;s instrument cor¬rection table must be used and applied properly. For accurate results, the anemometer should be returned to the manufacturer for periodic cleaning and checking. If it is in daily use, the anemometer should be returned about once per year, and proportionally less frequently if the usage is less frequent than on a daily basis. Smoke Tube The smoke tube may not appeal to individuals who believe that good measurement results can be obtained only with expensive, complicated, and fragile instru¬mentation. Nevertheless, smoke works about as well as anything for the routine measurement of low air velocities in mines. The following procedure yields reasonably good results: 1) Two marks are scratched 7.6 m (25 ft) apart on the floor of the airway. 2) The smoke tube is used to release a cloud of smoke in the center of the airway, about 0.9 m (3 ft) upstream of the first mark on the floor. 3) A timed interval begins when the leading edge of the smoke cloud passes over the first mark, and the interval stops when the leading edge of the cloud passes over the second mark. 4) A factor of 20% is subtracted from the cal¬culated velocity to determine the true average velocity, providing a correction for the centerline and for the spreading effect at the front of the cloud. Velocities calculated with the preceding method generally are accurate to within 10 to 15%. In some instances, the cloud from a conventional smoke tube

Jan 1, 1982

By Floyd M. Thorman

Gypsum is the crystalline chemical compound CaS04?2H20. A close chemical relation - and frequently occurring with Gypsum ? is Anhydrite which is Cask. Gypsun has wide commercial use because relatively simple heat processing reduces it to Plaster of Paris. While Anhydrite can be converted to Gypsum and thence to Plaster of Paris, the procedure is not simple and is quite costly. Anhydrite, however does have use in the agricultural field and in the Portland Cement industry. Occurrence of Gypsum in the earth structure is usually near or at the surface. Most underground mining is at 60 to 100 feet although one mine in southwest Virginia reaches a depth of 1300 feet. Gypsum is one of our softest minerals, rating only 2.0 on the Mohs scale of hardness. Specific gravity is 2.3 to 2.4. It is soluble in water but only slightly so. Interestingly, it is more soluble in cold water than in hot. For example, one part Gypsum dissolves in 370 parts water at 106° Fahrenheit while at 212°F. the water requirement is 452 parts. Compressive strength of massive Gypsum runs about 3000 lbs. per square inch. Color ranges from grey and brownish-grey to white.

Jan 1, 1973

By A. K. Sinha

A great potential market for the high BTU midwestern thermal coal exists if the coal is desulfurized and prepared to meet the environmental restrictions and the utility customer specifications. Because the midwestern coal is very high in pyritic sulfur, it can be adequately desulfurized by removing the pyrite with the help of such coal cleaning techniques as the froth flotation. Froth flotation cells are now commonly employed in modern coal preparation plants for recovering the fines but they are not utilized for desulfurizing the coal probably due to a lack of system operating data for such applications. A research project recently conducted at Southern Illinois University shows that the total sulfur in the midwestern coals can be successfully reduced from as high as 5.3 percent to less than 1.4 percent by single stage froth flotation. The results obtained on ten different samples of high sulfur coal obtained from different areas in the Illinois Basin are presented and discussed.

Jan 1, 1985

By A. Frank Alsobrook

DOUG HALBE: Thanks, Terry. And in spite of your introductory comments, I&apos;m going to attempt to continue our hallowed tradition of saying nice things about the speakers. This is really a serious comment now. We, as mineral processing and mill people, don&apos;t often talk to people outside our general operating area. One thing that we&apos;ve tried to do in this operators&apos; symposium is get speakers from various types of plant operations to help illustrate all the things we have in common. Our next speaker is from the industrial minerals area. I think there&apos;s a lot to be learned from industrial minerals operations. Some of the people in the last session learned some things about fine grinding in industrial mineral operations. I was a little surprised to see people there grind to 2 microns. Our next speaker is Frank Alsobrook. Frank is another nonmetallurgical engineer. He has a degree in geology, a master&apos;s of science from the University of Wisconsin. He&apos;s had his own very successful consulting company for a number of years. This is your 11th anniversary, Frank? Very good. He&apos;s also the immediate past chair of the industrial minerals division. I think the folks at the speakers&apos; table should be ashamed. You have been so rowdy that Frank chose to sit in the audience. [laughter] We&apos;d like you to come up now, Frank, and tell us some things that you&apos;ve seen that might be useful to us. INTRODUCTION FRANK ALSOBROOK: The three topics addressed briefly are (1) teamwork and operations modeling, (2) the pitfalls of capital conservatism, and (3) the potential for by-product recovery. Ideas for improvements in these areas are not unique to industrial minerals but apply to metal mining and processing operations, as well. Several additional topics are suggested at the end of the paper.

Jan 1, 1998

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By John A. Cordes, Thomas F. Torries

INTRODUCTION Nonfuel mineral markets have always tended to be volatile due to the cyclical nature of demand and the difficulty of fine-tuning capacity and output levels. Experiences over the past two decades, however, have been especially perverse. This short volume attempts to provide insights into this era and some guidance for the future. The papers are linked together by their focus on issues of productive capacity. At the same time, they provide a useful description, explanation and evaluation of the industry&apos;s evolution and its implications for the near-term. The regnant pessimism of the 1980s was very much alive during the early months of 1987 when the theme of this symposium was formalized. Indices of real metal prices had only inched-up from all-time lows in 1986. The hemorrhage of corporate red-ink was still a powerful memory. Frustration with the apparent inability of closures and reduced capacity utilization to re-establish market balance was strong. To the more pessimistic, the industry appeared destined to a quarter century of persistent excess capacity and nonremunerative prices. The conditions to support this pessimism were readily apparent. Economic literature tells us that surplus capacity is a complex, usually unexpected and often long-lived phenomenon caused by the interaction of at least three factors. The first is a rising capital-intensity of production. The second is the presence of aggressive new entrants whose capacity additions are typically (1) trade- dedicated because local market absorption is low; (2) cost-competitive for natural or policy-support reasons; (3) heavily burdened by debt-repayment obligations; and (4) viewed as important sources of employment, regional development and foreign exchange. The third, and often decisive, factor is an unanticipated decline or stagnation in demand growth for the sector&apos;s output. The first two factors combine to increase competitive pressures and to raise the actual or perceived cost of idle capacity. Market rigidity reduces responsiveness to price signals and distorts the burden of adjustment. Demand atrophy exacerbates these pressures especially on unprotected producers in the higher quadrants of the global supply function. In the mid-1980s, evidence of the existence of all these factors were easy to cite. Culprits were often identified. Claims for protection, global sharing of adjustment burdens, and imposition of disincentives to new capacity regardless of inherent economic status were co-dominant themes with the buzz-words of "competitiveness" and "level playing fields." This, notwithstanding the suggestions of the same economic literature that excess capacity persists longest when interventionist remedies permit it to continue. Today, only eighteen months later, the mood is decidedly more buoyant and most analysts are cautiously optimistic about the next few years. Many informed analysts have concluded that the excess capacity of the recent past has disappeared. For the present, the marketplace seems to have restored a balance between supply and demand. That the adjustment took five or six years longer than anticipated attests to the dramatic structural changes which have characterized the industry. The implications of these changes for the future are unclear. Were the macroeconomic shocks, coupled with industry transitions, so extraordinary in magnitude and timing that experiences were unique? If so, the next years may hold more stable and cautious times for the industry. Alternatively, is the inherently volatile metals industry facing a future of cycles equally perverse in terms of amplitude and duration due to economic uncertainities and inflexible industry response capabilities?

Jan 1, 1989

By D. Altizer, E. Thompson, K. F. Unrug

Because of frequent sudden changes in the geologic composition of strata, the extrapolation of rock properties obtained from core samples to the surrounding areas can cause problems. To address this issue, a method of rapid strength testing in situ using a borehole penetrometer is being developed. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. Rock strengths are determined di¬rectly on the drill-hole wall. The latest development is a borehole penetrometer that requires only a 38.1-mm- (1.5-in.-) diam hole. The small diameter of the penetrometer body allows for the drilling of test holes with production mine equipment such as a roof bolter. The new penetrometer allows for the possibility of a broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 2002

As mentioned in chapter 8, one of the objectives of the budget is to provide a mechanism for ongoing measurement and control of the production operation. The budget shows expected performance. Actual results are compared to this benchmark to evaluate past performance and to direct future activities. The variances between budgeted and actual results identify specific activities that did not perform as expected (whether negatively or positively). Managers who use variance analysis are essentially applying a management- by-exception philosophy. Individual organizations will determine variances that reflect their own processes and managerial interests, but these variances all follow the approach outlined here. Firms will also vary in the extent to which variances are reported. Some firms use a few variance measures for the overall production organization whereas others calculate variances for individual departments or even individual work areas. As mentioned in chapter 5, it is important to distinguish between controllable and noncontrollable costs when using budgets for control and evaluation.

Jan 1, 1999

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

By J. E. Hoffman, S. P. Sandoval, T. J. Keefe, K. P. V. Lei, O&apos

The U.S. Bureau of Mines investigated the use of the Fe2+/Fe3+-SO2 (FFS) anode reaction in the copper leaching-solvent extraction-electrowinning circuit. The investigation revealed that six process variables, including anode type, Fe 21 concentration, current density, electrolyte temperature, degree of agitation, and manifold injection point were found to influence cell voltage and cell current efficiency. A 47% voltage reduction (0.8 versus 1.5 V) compared to conventional electrowinning with activated lead (ALE) anodes was achieved at a current density of 258 A/m2 (24 A/ft2) with an industrial electrolyte. Current efficiency was maintained above 90%, and S02 above the cell measured less than 1 ppm when activated carbon was used to assist the reduction of Fe" by S02 in the copper electrolyte. Solvent extraction tests showed that Alamine 336 is a stronger H2SO4 extractant than is needed to extract the excess acid produced by the FFS anode reaction.

Jan 1, 1993

By Brian W. Hester

All gold occurrences in Tanzania are of Precambrian age and in geological settings similar to gold deposits in other parts the world. The three main areas of interest are perhaps the least prospected of areas of gold mineralization in Precambrian rocks in non- aligned, or market economy nations. Historic production exceeds 77.660 kg (2.5 million oz). Current results by small scale workers go unreported, but have been estimated to be as high as 11.000 kg (350.000 oz) annually. Gold occurs in both lower and upper Precambrian rocks. In the older. gold is associated with greenstones and iron formations typical of many cratonic areas of Precambrian age. The Tanzanian Craton lies in the north west quarter of the country where it is flanked on both east and west sides by mobile belts involving upper Precambrian rocks of high metamorphic grade. Gold occurs in fractures in the western belt within two distinct areas.

Jan 1, 1989

By Olli Järvinen

The precious metal refinery process is divided into the five process stages: 1 .copper/nickel leaching in autoclave 2. selenium roasting furnace 3. doré metal smelting furnace 4. silver electrolysis 5. gold recovery system. The process has been developed during the years in Outokumpu Harjavalta Metals, which treats about 600000 kg /year copper anode slime. The slime treatment process route in Outokumpu Pori plant has been developed from year 1941. During this period the process has been improved radically. The major changes has been the atmosphere leaching into the autoclave leaching, the sulfuric acid roasting furnace was changed into sulfuric dioxide / oxygen roasting. The old doré smelting furnace has changed into the TROF converter and the gold electrolysis / aqua regia process has changed into the quick hydrochloric acid leaching process. The current production in Pori plant is 30000 kg of silver, 1000 kg gold, 30000 kg of selenium and some hundred kg of platinum- palladium concentrate.

Jan 1, 1995