Search Documents

By D. R. Hembree

This paper discusses the mineralogy and metallurgy of the Kuroko-style volcanogenic massive sulfide ores mined at Formosa Exploration Inc. I s Silver Butte Mine located in southwest Oregon. The principle ore type is pyrite + chalcopyrite + sphalerite, while subsidiary pyrite + bornite + sphalerite ore is also mined. The two styles of mineralization have distinctly different metallurgical behaviors and must be treated separately. Selective flotation methods are used to produce copper and zinc concentrates from the first ore type, while bulk concentrates are produced from the bornite ore. Careful mine planning and coordination between the mine and mill are utilized to achieve optimal recoveries.

Jan 1, 1993

By Brij M. Moudgil

Separation of dolomite from apatite, because of nonselective adsorption, cannot be achieved by conventional froth flotation technique. Results obtained in the present study also indicate, that this can be attributed to the depletion of the collector molecules due to complexation with the calcium and magnesium ions, dissolved from the two minerals. However, it has been established in this investigation that conditioning the material at pH 10, followed by reconditioning, without any additional collector, at pH 4, results in selective flotation of dolomite from the mixture. The recovery of apatite, in the proposed reconditioning process, is much higher than with the conventional conditioning under similar pH conditions. The mechanisms involved in the conventional conditioning, and the reconditioning process are presented.

Jan 1, 1983

By Dale W. Norris, John A. L. Campbell

INTRODUCTION Optimization, as measured by productivity gains, is being achieved in our nation's preparation plants principally by automation, economy of scale, and reducing maintenance. Increased tonnage per unit of investment, a1 so a measure of optimization, is being achieved by breaking with tradition and increasing plant utilization, while simultaneously improving on equipment re1iabi1ity. Improved qua1ity, another measure of optimization, is being attained through technical innovation. This review will concentrate on state-of-the- art unit operations and processes, and will not discuss emerging new technologies which are covered in detail in other presentations of this symposium. It is recognized that much of what will be discussed in this paper is not unique to the fine coal circuit, but is equally applicable to the entire preparation plant. However, the areas reviewed are the principal means being used today to optimize an existing preparation plant's fine coal circuit. Prior to designing and optimizing a fine coal cleaning circuit, the question that must first be answered is, "Do we even want a fine coal circuit? This is a much more complex question than is readily apparent, as most of you recognize. It can be argued either way. In the final analysis the "bottom line" will hold (Blackmore, 1982). If your sales contract a1 lows it, and the selling price can justify it, you most assuredly want to build a fine coal circuit into your preparation plant. In general today, most new preparation plants do have fine coal cleaning circuits. The purpose of fine coal cleaning has changed with time. Some of the early applications of fine coal cleaning were to prevent stream pollution rather than to prepare a product for market (Merrill a Pennington, 1962). During the 50's, 60's and into the 70's the principal thrust of fine coal cleaning was in metallurgical coal preparation. More recently, the emphasis of the 80's is on steam coal processing. There is no consensus on what is fine coal. Traditionally, fine coal would be anything below 1/4" in size. Because of the advances being made in intermediate coal cleaning processes, i.e. heavy media cyclones and jig cleaning, this discussion will define fine coal as -28 mesh (Aplan, 1987). Figure 1 is a plot of the size ranges of a large number of U.S. bituminous coals. In general the -28 mesh fraction of a bituminous coal will be between 7% and 18% of the ROM feed with reported ranges of 5% to 40% (Aplan, 1987). Consequently, traditional fine coal cleaning is general 1 y involved with a re1 actively mi nor portion of the coal feed. Every effort is taken both in terms of mining and preparation to keep it that way because of the high cost of cleaning fines. The move away from this posture, namely, the techniques to fine grind coal to liberate pyrite is probably the biggest challenge facing fine coal processing today.

Jan 1, 1988

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By S. A. Hoenig

Introduction In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in Fig.1 . Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in Fig. 1. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 µm (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 pm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform. *The zeta potential is the voltage developed between the surface of a solid particle and the ion solution in which it is immersed. In the case of rock/ore materials in water, the zeta potential is negative.

Jan 1, 1984

By James A. Morrison, Stephane Carayol, Paul H. Madsen

The Rio Piedras Alignment Section 7 of the Tren Urbano is currently being constructed beneath a historic commercial section of San Juan. Different portions of the section are being constructed using open cut, cut-and-cover, New Austrian Tunneling Method (NATM), Earth Pressure Balance Machine (EPBM), and as tacked drift mined support system. The combination of complex geology, low ground cover, and several innovative construction methods present many challenges to the ground control program. Mining and construction sequences were first developed to minimize ground movements and risk of damage to structures. A unique compensation-grouting program was developed to improve the ground, limit settlement, and recover settlements incurred due to mining.

Jan 1, 1999

By Jon Kellar, William Cross, Eric Swanson, John Starkovich

Zirconium tungstate (ZrW2O8) is a unique material with a negative coefficient of thermal expansion. In order to fully utilize this material as a filler, a surface treatment needs to be developed to better improve the wetting and dispersion capabilities of the filler. This paper describes an initial study to characterize the filler as well as investigate fatty acid and silane surface treatments for eventual compounding with thermosetting matrices. It was found that ZrW20, has a point-of- zero charge between pH 2.7-3.0, and that both fatty acid and organofunctional silane treatments appear to be viable surface treatments for this unique filler.

Jan 1, 2003

By Carrie Smith

Mining has historically been one of the most male-dominated industries in the world. From underground operations to executive boardrooms, the presence of women has often been slim. Women had often been excluded from operational, leadership and decision-making roles, both by cultural norms and systemic barriers. According to PwC’s Global Mine Report (2023), women represent around 14 percent of the global mining workforce. Leadership representation, however, remains sparse, with S&P Global’s 2023 report showing women holding approximately 12 percent of C-suite positions and only 3 percent of senior leadership roles globally. These figures reflect persistent gaps, but they also highlight the progress driven by a new generation of women transforming the industry. Despite the gender imbalance among mining workers, women have continuously made grand strides within the industry, resulting in pivotal changes. At the forefront of this transformation is Kimberly Morrison, one of several women who have played pivotal roles in shaping the mining sector.

Aug 1, 2025

By Ing. H. Kellerwessel, Ing. M. Esna-Ashari

This paper refers to the new crushing and grinding process, invented by Professor Schonert (Ref. 1), Clausthal, Germany. The process is known as high pressure particle bed comminution or interparticle crushing. Several papers already describe fundamentals of the process, the equipment used, results of lab size and large scale tests and the first results of commercial operations (Ref. 2 to 7). Of course, we will treat the topic from the perspective of a downstream gold ore upgrading or leaching process. Some recently executed testwork indicates that the process provides special advantages in this field. To describe the process generally, in view of the already existing publications.

Jan 1, 1998

By Christopher J. Bise

Traditionally, mine drainage systems have not received the high level of emphasis on careful engineering design which has been rendered to many of the other auxillary operations. This may be due, in part, to the situation-response approach toward dealing with an influx of water. When the installed system becomes inadequate, costly alterations to the pump, such as staging or speed increases, are considered expedient solutions. In order to rectify this situation, computer-aided solutions to mine drainage problems could represent an efficient alternative to the methods presently used. This paper will consider the application of microcomputer technology to mine drainage problems and will show how the relative economy and convenience of microcomputers can make them become valuable analytic tools at any mine site.

Jan 1, 1983

By R. K. Mehta, C. W. Schultz, J. B. Bates

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained. Experimental equipment and procedure The arrangement of the column cell and auxiliary equipment for continuous flow testing is shown schematically in Fig. 1. The feed sump [O] is filled with a sufficient volume of prepared sample to permit a large number of tests to be performed (typically 12). Past experience has shown this is necessary to control sample variability and variability in the size distribution resulting from ultra fine grinding. The feed slurry is maintained at about 20% solids and is constantly recirculated and stirred. The sample is metered from the circulating pipe by a peristaltic pump [O]. The feed slurry is diluted with reagentized water [O] by a second peristaltic pump [O]. Wash water [O], also reagentized, is supplied through a third peristaltic pump [O]. While this feed system may seem unduly complex, it does permit users to independently vary either the wash water rate or the net solids content of the cell. In the tests reported here, the feed rate and net percent solids were constant at 12.5 gms/min. and 3.3%, respectively. Diluted feed enters the column through 6.35 mm-diam (0.25 in.-diam) copper tubing and is discharged upwardly at the center of the column. Tailings are discharged through flexible tubing that can be adjusted so as to control the position of the pulp-froth interface. The column is 76.2 mm-internal-diam (3 in.-internal-diam) and 1090 mm (43 in.) high. It is made from lucite tubing and is fitted with a 51-mm-diam (2-in.-diam) fritted glass air sparger having an average pore diameter of 50 µm. In performing a series of tests, the concentrate and tailing are allowed to discharge continuously. The system is allowed to equilibrate for 30 minutes after the pulp and froth reach operating levels. Concentrate and tailing samples are taken simultaneously for timed intervals (five to 15 minutes, depending on the volume of sample desired). After sampling, a change in operating conditions is made and the system is again allowed to equilibrate. The tests to determine the effect of the pulp-froth interface level were part of a larger series of tests in which the objective was to optimize the conditions for a rougher flotation stage in a two stage circuit. The sample used in this series of tests was an Alabama shale ground to d90 = 23.1 µm and d50 = 7.9 µm. The operating conditions remaining constant in this series of tests were as follows: Column height - 1600 mm (63 in.) Air sparser - 50 µm (average pore diameter) Spray water - 130 cc/min. Feed rate - 12.5 gm/min (0.4 oz per min) (dry solids) Percent solids - 3.3% Frother (Dowfroth 250) - 45 ppm The variable test conditions are tabulated in Table 1. Positions of the pulp level (pulp froth interface) and feed entry are presented as a percentage of column height (as measured from the face of the air sparser). These test conditions are presented Fig. 2. At each of these test conditions, individual tests were performed at varying air

Jan 1, 1992

By S. Michael Feroz, Paul Gribbon, Jan Rosholt

Approximately six billion gallons of combined sewage are discharged annually into Willamette River and Columbia Slough through Portland’s combined sewer system. The Columbia Slough Consolidation Conduit (CSCC) is an important element of mandated Combined Sewer Overflow (CSO) abatement. It includes2,548m (8,361 ft.) of 3.7 m. (12 ft.) internal diameter tunnel. The CSCC alignment traverses the UP railroad, Columbia Boulevard and parallels an old sewer. Geologic conditions include river alluvium and fine to coarse-grained flood deposits containing cobbles and boulders. This paper describes design and construction of a tunnel in soft-ground, with shallow cover and close to an old concrete sewer.

Jan 1, 1999

By Robert L. Marovelli

Organizational development that attempts to simultaneously deal both with training and with job design parameters as they relate to mine health and safety, productivity, and quality of life is one of several areas of research that the Bureau of Mines is pursuing. The Bureau sees potential in this particular effort for reducing accidents and injuries, improving worker satisfaction and health, and increasing productivity.

Jan 1, 1981

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By Donald D. Gullickson

The entire system is built around pre-designed and pre-engineered modules which are assembled to meet the metallurgical and production parameters of the project. The carbon vessels are the key to the flexibility of the system. The vessels are made of a coated mild steel, which allows the carbon vessels to be used in the adsorption, desorption and acid wash cycles. In the adsorption mode, the solution is pumped up-flow through four (4) vessels in series at 250 gpm fluidizing the carbon bed. When the carbon in the lead vessel is loaded, it is disconnected from the adsorption circuit via rubber hoses with quick-disconnect fittings. The second vessel is then made the lead vessel and a stripped carbon vessel is added to the end of the adsorption circuit.

Jan 1, 1998

By Patrick B. Kenny

Generally speaking, it is safe to address this conference as a conclave of Engineers, Owners' Agents, Governmental Representatives, and Contractors. As a group, we have assembled here to learn of our compatriots engaged in similiar underground operations throughout the United States and the World. We are here to learn of improved methods, higher technology, and better management. Through the acquisition of this knowledge, we each hope we can improve our own particular services, products and projects. This session is dedicated to a discussion of "Costs". The most apparent reason for a discussion of costs at this level is to expose subjects affecting costs and propose methods to reduce them. From that premise a contractor can identify three areas of discussion: design considerations, contract considerations, and governmental considerations. A fourth area of consideration is an introspective view of the contractor's role in the design construct process. Unnecessary costs and risks attributable to these areas are contributing excessively to ever increasing project and system costs. DESIGN CONSIDERATIONS On April 20, 1977 the Metropolitan Sanitary District of Greater Chicago accepted proposals for the Tunnel and Reservoir Plan on Contract A and Contract B. This letting called for construction of over 33 km (21 miles) of the Mainstream Tunnel bored at 9.75 m (32 ft) to 10.67 m (35 ft.) in diameter. Also included were all the appurtenant collecting and regulating structures. The proposal allowed the

Jan 1, 1979

By M. Birdsell

"Sustainable long-term restoration requires adequate planning and preparation, implementation, and measurement goals to monitor success associated with restoring sites to pre-disturbance levels of ecological health. The Buckhorn Mountain Mine riparian habitat restoration project has been a multi-year endeavor with a variety of restoration techniques implemented by Kinross Gold/Crown Resources Corporation. INTRODUCTION The Buckhorn Mountain Mine procured mitigation lands during the permitting process to be set aside for long-term restoration. A portion of this mitigation land included three aquatic habitat mitigation parcels; a spring and wetland complex and two stream and riparian corridors. These properties were historically used for agriculture purposes and livestock grazing. During initial permitting, habitat monitoring and mitigation plans were created to help guide restoration, and provide measures for success. Various techniques and adaptations have been implemented on the properties since 2007, and continued efforts are being implemented annually to ensure the long-term success of the project. Field measurements are collected annually to ensure mitigation objectives are being met, and provide opportunity to modify restoration efforts when necessary. MATERIALS/METHODS Restoration efforts have included implementation of several methods including livestock exclusion, treatment of state and locally listed noxious weed species, installation of regionally sourced riparian plant species and local stock willow cuttings. Annual mechanical and herbicide treatments for noxious weeds have been conducted annually. Efforts to control reed canarygrass (Phalaris arundinacea) have been implemented since 2013; methods include mechanical and herbicide treatments. A combination of methods has been employed to help aid restoration of native species within the riparian corridor, and increase survival of planted species, including weed matting and browse barriers to aid riparian planting success. Instream planting of local stock willow have also been employed to increase stream vegetative cover and provide long-term bank stabilization. Most recently, a perched culvert near one of the properties has been replaced with an aquatic life passable culvert designed to aid in the upstream migration of fish species into the stream system. Efforts to provide increased fisheries into upstream portions of the system and aid in restoration of stream bed and bank have been employed to increase the ecological value downstream of the replacement. In addition to efforts completed by the client to provide restoration efforts, a local non-profit organization, in conjunction with the client, installed beaver dam analogues (BDAs) in the fall of 2014. These structures are intended to raise water levels along stretches of incised channel in an attempt to flood historic off-channel floodplain"

Jan 1, 2016

By J. A. Oraniscak

Longwall mining operations continue to increase extraction rates and the potential to generate higher amounts of airborne respirable dust (ARD). The National Institute for Occupational Safety and Health (NIOSH) has gathered data from underground longwall surveys and laboratory crushing tests to identify the important factors influencing the amount of ARD levels generated. Coal-seam characteristics, operational parameters (i.e.,cut sequence, mining height, etc.), extraction rates and dust-control parameters (i.e., airflow, water flow, etc.) were examined to determine their influence on ARD levels measured at longwalls during actual mining operations. ARD generated by a laboratory crusher while crushing bituminous coal samples collected from underground longwalls was also examined to determine if there were cor relations with coal-seam properties. Results from the longwall and laboratory data collected indicated that low-ash, high-volatile coals (low moist fuel ratio or MFR coals) generate higher amounts of ARD. It was found that face ventilation and water application to the coal product are essential elements to controlling longwall ARD levels.

Jan 1, 2000

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By Thomas E. McNider, Robert C. Howell, J. W. Stevenson

As of the end of October, 1990, there have been eight spontaneous combustion heatings reported to the Mine Safety and Health Administration (MSHA) at the No. 5 Mine. A reportable heating is defined as one with elevated surface temperatures of the strata greater than ll°C (20°F) above the ambient. The first heatings occurred in November, 1986. The last three heatings were located near the start line of "K" Longwall Panel in the southwest where mining had begun on May 21, 1990. All of the heated areas had been at the time of detection, or were sometime areas of high ventilation pressure differentials or high air velocities. All of the heated areas are in an expanded seam with associated, extensive floor heave which is characteristic of all of the expanded seam thus far exposed by development mining in the No. 5 Mine. Jim Walter Resources, Inc. submitted a plan to MSHA which would reduce the potential for spontaneous combustion at the No. 5 Mine by reducing high air velocities and high pressure differentials in the gob. These two parameters are the dynamics which feed oxygen to the pyrite, thus initiating the oxidation process which can lead to spontaneous combustion. No. 5 Nine operated under this plan for 29 shifts before mining on the longwall was stopped by MSHA and the Spontaneous Combustion Control Plan revoked. This paper briefly details the geology of the expanded seam and history of the heatings. It also gives a retrospective view of the operation under the Spontaneous Combustion Control Plan and reasons why it was revoked by MSHA. Currently, knowledge of the reaction process of the footwall coal seams at No. 5 Mine and other potential spontaneous combustion seams in the United States is limited. There are techniques used in the United States and other countries to minimize the potential for heatings in spontaneous combustion prone areas. The No. 5 Mine has attempted to utilize this current technology. However, in deep, gassy mines the problem is complex.

Jan 1, 1991