Search Documents

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By B. Anameric, S. K. Kawatra, K. B. Rundman

The iron nugget process is an economical, environmentally friendly, cokeless, single-step pig iron making process. Residence time dependent process requirements for production of pig iron nuggets at a fixed furnace temperature (1425 C) were investigated. Three chemically and physically different products were produced after complete reduction to iron, depending on the residence time in the furnace. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets (PIN). The increase in the carbon content of the system as a function of residence time was detected by optical microscopy and Microhardness measurements. Sufficient carbon dissolution for the production of pig iron nuggets was obtained after 40 minutes residence time. The pig iron nuggets produced had chemical and physical properties similar to blast furnace pig iron. They were liquid state products and slag was completely separated from the metal.

Jan 1, 2005

By Francis J. Kiessling

Energy and the conversion of potential energy into alternate forms is becoming a topic of household conversation for a larger segment of the world's population as mankind's desire for products derived from the vast array of technological developments continues to expand. The world's use of steel and the high energy consumption related to the production of steel promotes an awareness of the limitations of existing technology and a search for more economical alternates. Terminology such as (BF) Blast Furnace, (BOP) Basic Oxygen Furnace, (EAF) Electric ARC Furnace, (DR) Direct Reduction, (DRI) Direct Reduced Iron and (FC) form coke is becoming commonplace as alternates are being sought to alleviate the energy crunch. Coke production by various methods was developed as early as the seventeenth century in Europe to replace the disappearing hardwood forests that supplied the initial blast furnace fuel in the form of charcoal. In 1880, the Semet Solvay by-product coke oven design was introduced to the United States at Syracuse, New York, to supply coke for use in the production of soda ash, coke oven gas and its by products as the primary source of many organic processes. Although the Semet Solvay coke oven has not been marketed for decades, these coke oven batteries are in use today producing metallurgical coke, coke oven gas, and related by-products.

Jan 1, 1980

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

By P. Zhang

A multiyear, comprehensive study of flotation reagents used in phosphate beneficiation was conducted. The study involved the evaluation of pure fatty acid compounds, comparison of various anionic collectors and testing of iso-acids. Various C12 to C22 fatty acids were tested as Florida phosphate collectors. The saturated fatty acids were found to be very poor collectors when using the standard conditioning procedure, whereas the unsaturated C16 to C22 fatty acids showed fair to good phosphate collecting ability. The C18 fatty acids oleic, impure oleic and linoleic and the C20 eicosenoic acid were shown to be the best phosphate collectors. The best flotation results were obtained using Liqro GA tall oil and oleic acid. Four isostearic/iso oleic acid type fatty acid collectors were compared with a commercial grade oleic acid and with Liqro GA tall oil as phosphate collectors using standard laboratory conditioning and flotation procedures. The most selective collector evaluated was Century 1108, a high isostearic acid-type reagent. However, it was concluded that this excellent-performing reagent was too expensive for commercial use. Overall, the most promising reagent was probably Century MO-5. This collector is essentially an iso-oleic acid/stearic acid mixture (not isostearic acid), and it costs much less. This program laid a sound foundation for developing single collector, all anionic flotation processes.

Jan 1, 2009

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

The central question concerning the health risks associated with mining and processing of taconite ores in the Eastern Mesabi Range is ??does asbestos, of any variety, occur within the gangue mineral population?? Free silica in the form of quartz does exist in the taconite, but silicosis has been relegated to a secondary issue. The focus has shifted to the asbestos minerals and the malignancies that might occur following low-level exposure to dust. Although mineral fibers do exist in the Mesabi taconite ores, Ross, Nolan and Nord conclude ??no asbestos?, as explained in their contribution ??The Search for Asbestos within the Peter Mitchell Taconite Iron Ore Mine, near Babbitt, Minnesota?. Their area of study is located in the eastern Mesabi Range. It is here that the tectonic and metamorphic effects associated with the intrusion of the Duluth Gabbro have been profound. A variety of amphibole minerals have developed as a result of these geological events, some with names recognized within the US Asbestos Standard. The issue tackled by the authors is whether or not these amphiboles are present in the mine and if so whether or not they are asbestiform in habit.

Jan 1, 2008

This international symposium was convened to assess the current state of knowledge concerning the health hazards that might be associated with the ingestion and inhalation of fibrous particles produced from the processing of taconite ore. Concern about fibrous particles in taconite arose from their similarities to amphibole asbestos minerals that are known to be human carcinogens. The mineralogical characteristics of asbestos fibers are reviewed and compared with the fibrous particles known to be present in taconite ore from the eastern end of the Iron Range. The epidemiological and experimental animal studies for asbestos-related disease (including gastrointestinal cancer from asbestos in dinking water)were critically evaluated andcompared to those of the fibrous minerals in the taconite. The focus was on the amphiboles in the cummingtonite?grunerite and tremolite?ferroactinolite series and other fibrous particles in both the Iron Range and the Duluth Complex. This included examination of the reported occurrence of any asbestiform ferroactinolite, crocidolite asbestos, chrysotile asbestos, etc. In addition, an effort was made to provide a scientific framework to address fibrous minerals, which may be associated with nonferrous mineral deposits in the Duluth Complex. State-of-the-art risk assessment models for asbestos were presented. Risk assessment scenarios were developed for taconite-derived fibers at environmental exposure levels related to the operation of the Silver Bay taconite processing facility. These calculated risks were found to be trivial even after it was assumed that all mineral fibers were as carcinogenic as amphibole asbestos.

Jan 1, 2008

By Christopher J. Bise

INTRODUCTION Traditionally, the purpose of mine ventilation has been defined as diluting, rendering harmless, and sweeping away hazardous gases which may accumulate in the mine workings. In addition, the ventilation sys- tem must keep the mine air as close as possible to the composition of the outside air in order to provide a healthy environment for mineworkers and to prolong the useful life of mine equipment. When plans are being developed for opening a new mine, sound engineering dictates that a calculated estimate be made of both the maximum air quantity requirement and the accept- able mine pressure (head) loss related to the under- ground layout and projections. For efficient mine ventilation, the two problem areas that demand constant attention are (1) the control of fugitive air (through short circuiting or leakage) and (2) the provision of ample airway capacity. Fugitive air is that quantity of air which enters the mine but short-circuits the mine ventilation system through improperly constructed stoppings, doors, overcasts, etc.; it represents an investment in power consumption (to move the air by the fan) while providing little, if any, return on the investment. Typically, efficient mines are those that can deliver 50% of the air handled by their fans to the working faces. Paying close attention to a new mine's ventilation system at the outset can provide numerous benefits during the later stages of mine development. It has often been noted that the main cause of trouble in many mine ventilation systems can be found within a radius of 2500 ft from the fan installation. Ample airway capacity is essential to maintain the mine's head loss within manageable limits. Similar to an industrial ventilation setting, the mine's headings are the ductwork for the handling of air. The difference between normal industrial ventilation and mine ventilation is apparent when more capacity is needed; a plant can install new or larger ductwork, but it is difficult for a mine to install new entries or enlarge existing entries. Air velocities are usually maintained under 800 fpm to limit the stirring up of dust in the intakes. With this in mind, it is usually simple to estimate the number of entries required in the ventilation system. The problem that often arises, though, is when the system's capacity is overestimated and the required head loss to achieve the desired quantity is excessive. Experience has shown that problems are often encountered when the mine's condition requires much more than three inches of water gage to ventilate the mine on a day-to-day basis. Thus, if proper attention is not paid to these parameters in the preplanning and initial development of a new mine, it may take an extremely high water gage to achieve the ultimate quantity. This chapter will not delve deeply into the theory of mine ventilation; many other books have been writ- ten on that subject. Instead, the following sections will point out the important considerations that should take place before the development of a mine ventilation system, as they relate to normal industry practice. FUNDAMENTALS OF AIRFLOW Volume Versus Water Gage The common method of measuring ventilation pressure is in terms of inches of water gage (wg); one inch of water corresponds to a pressure of 5.2 psf (pounds per square foot). Further, airflow follows a square-law relationship between volumes and pressures where, as shown in the previous section, a doubling of quantity requires a quadrupling of pressure. Table 1 shows how heads and quantities are related. Using Table 1, it is readily apparent that, for the same mining conditions, an increase in pressure from one inch wg to three inches wg results in only 34,640 cfm when the initial quantity is 20,000 cfm. Pressure Losses Pressure losses in mine ventilation systems are caused by friction between the heading walls and the air stream and by shock losses due to abrupt changes of the air stream caused by obstructions. The common pressure-loss formula for mine ventilation is: [ ] where H is the pressure loss in inches of water gage, K is the coefficient of friction, L is the length of the airway in feet, 0 is the airway perimeter in feet, V is the air velocity in feet per minute, and A is the cross-sectional area of the airway in square feet. Table 2 lists the US Bureau of Mines schedule of friction factors (K) for mine airways. Recent research indicates that the values of K are slightly less for coal mines than those presented in the USBM Schedule, and Table 3 should be consulted in this instance. It should be

Jan 1, 1986

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

The average annual growth rate of real gross domes-tic product (GDP) from the third quarter of 2001through the second quarter of 2003 in the United States was about 2.6 percent. GDP growth rates in the third and fourth quarters of 2003 were about 8 percent and 4 percent, respectively. Many other indicators reflected a rebounding U.S. economy — rising consumer confidence, higher retail sales, greater industrial production and more housing starts. Inflation also reached a 38-year low in 2003. The upward trends in many sectors of the U.S. economy in 2003, however, were shared by few of the mineral materials industries. Annual output declined inmost non fuel mining and mineral processing industries, although there was an upward turn toward yearend as prices began to increase (Table 1).

Jan 1, 2004

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

By S. J. Jung

The most frequent causes of accidental injury and fatality are carelessness and ignorance; and the most common accidents are haulage accidents, fall, drowning, and fire. However, in this modern day and age, severe injury has become the dire consequence of an ever-increasing number of industrial and mining accidents as well as sport-, military- , etc. Mine accidents have declined dramatically in number and severity through decades of research, technology, and preventive programs. However, preventing recurrence of disasters like those of the past remains a top priority requiring constant vigilance by management, labor, and government. The goal of the present research is to investigate and identify root causes associated with types of mining accidents (victim being caught by an equipment, bodily motion, over exertion, etc) and nature of injuries such as (sprain and strains, fracture, dislocation, amputation, etc). Further, we hope to discover the impetus of the root causes occurring more and more often in this modern day of technology and quality awareness. With the different dimensions of accidents and injuries brought into the fold, there is the need for researchers and mining operators to comprehend and better still visualize significant patterns of associations among these variables of interest. We assume that, there is a high correlation between many dimensions of nature of injuries and types of accidents. This suggested a principal component analysis to reduce the dimensions for easy and amenable interpretation.

Jan 1, 2012

By Michael Hughes, Paul Bonapace, Harry Charalambu, Stephen Rigbey

Ontario Power Generation is building a 10.4-km water diversion tunnel in Niagara Falls, Canada. The tunnel is a two-pass, cast-in-place prestressed concrete-lined pres-sure tunnel with a nominal internal diameter of 12.7 m. It is mostly situated within the Queenston formation which swells in contact with fresh water and has very aggressive groundwater. Tunneling in this material presents challenges in both design and construction. The tunnel design includes for a membrane to eliminate the potential for rock swelling and to protect the concrete liner from the ground conditions. A unique three-stage Geotechnical Baseline Report (GBR) is being used and is expected to provide an equitable method of dealing with any variations in subsurface conditions.

Jan 1, 2007

By Sarah Holtz Wilson, Kenneth Rossi, Carl R. Handford, David F. Tsztoo

The East Bay Municipal Utility District’s Claremont Tunnel is an 18,000-foot long water tunnel that crosses the Hayward Fault zone near Oakland, California. It was originally completed in 1929. This project involved the construction of a bypass tunnel through the fault zone, including an enlarged vault section designed to accommodate up to 8.5 feet of horizontal offset. Ground conditions encountered included sheared and crushed serpentinite and clayey fault gouge, and presented specific challenges for construction. A special excavation and support sequence used concrete-backfilled side drifts as foundations for the vault steel sets. It also allowed for a 20-foot-wide top heading and bench excavation in soft and squeezing ground conditions.

Jan 1, 2007

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002