Search Documents

By H. Salamanca

The electric operation and design features of the 11.000 H.P. variable speed SAG mill gearless drive is presented. The function of the frequency converter, control system drive and lubrication systems are described. An analysis of the harmonic characteristic in the Supply System and Motor is presented, and the dynamic development of the stator current, speed and the magnetic flux in the start-up process of the drive is evaluated. Besides, the most important aspects in the commissioning and maintenance of the drive are analyzed.

Jan 1, 1991

By Z. Yu

Dewatering of a -0.5 mm fine coal has been studied extensively. Deep cleaning requires however fine grinding, and dewatering of such ultrafine products presents a great challenge. Several coal samples finely ground and characterized by different wettabilities have b.een used in the filtration tests. Vacuum and press filters have been employed. In this paper only the results obtained with different flocculants (totally hydrophobic. semi-hydrophobic and hydrophilic polymers) are included. The results reveal the effect of coal surface properties and flocculant type on filtration of ultrafine coal.

Jan 1, 1994

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

"From 2011–2016 there were 1,511 documented injures, including 7 fatalities, from ground falls in U.S. underground coal mines. The majority of these ground fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely utilized in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Mine Roof Simulator (MRS) in Pittsburgh, PA. The load-displacement characteristics of a 2.4-m x 3.7-m panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of displacement loading rate, load pull surface geometry, and the inclusion of roof channel on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines. INTRODUCTION Over 1,500 injures, including 7 fatalities, occurred from 2011–2016 from ground falls in U.S. underground mines with the majority of these ground-fall injuries caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Comptonet al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Pittsburgh Research Laboratory (PRL)."

Jan 1, 2018

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always be the first action during the rescue operation. Unfortunately, in many cases, the escape-ways (escape routes) dedicated for miners' evacuation are contaminated with fire byproducts from adjacent entries. The purpose of this paper is to present the ventilation control process that will maintain the escape-way free from contaminants and available for travel. Several scenarios in a different section on ventilation system arrangements are analyzed, discussed and presented. To perform these studies, the author used a mine-fire simulator, which provides a dynamic (in real time) representation of the fire's progress and also gives a display, a color-graphic visualization, of the spread of combustion products throughout the ventilation system. Presented and discussed in this paper, also, are ways in which the mine-fire simulator can be used as a training and teaching tool for miners and, particularly, for ventilation and safety personnel.

Jan 1, 1993

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By Glenn H. Damon

Concern about environmental pollution goes back many centuries, but until recently most efforts to control it have been perfunctory and spasmodic, aimed largely at coal smoke and other visible pollutants. Air pollution is to a large degree a byproduct of our economic development, and scientific knowledge of the causes and character of such pollution is more extensive than the technology to handle the waste byproducts of our industrial civilization. The removal of all constituents foreign to the air from the effluents produced by an industrialized society is obviously impractical at this time. There is widespread difference of opinion regarding acceptable ambient air concentration levels for the Various pollutants produced by combustion processes, but there is basic agreement that the pollution of the atmosphere must be controlled and eventually reduced. The magnitude of the air pollution problem has been increasing rapidly because our expanding economy calls for an ever-increasing consumption of energy, and fossil fuels are a principal source of energy. For example, the consumption of electricity has been increasing at an average annual rate of approximately 8 percent over the last 10 or 1.5 years. Table 1 shows the estimated emission of the principal pollutants into the atmosphere in 1966. The approximately 90 million automobiles, trucks, and buses on American highways contribute the largest proportion of pollutants to the atmosphere, but that fact does not alter the growing problems of the coal industry. You will note that sulfur oxides, particulates, and nitrogen oxides are all products of the combustion of coal. Of these air contaminants, sulfur oxides are now receiving major emphasis in terms of research to develop effective means for control, Table 2 shows that the combustion of coal produces approximately 60 percent of the sulfur oxides discharged to the atmosphere. While the utilization of coal is the principal source of particulate matter, this is not considered as serious a problem as it was in the early part of the century because of technological developments that have produced sound methods for the removal of particulates from waste gas streams.

Jan 1, 1968

By Sidney V. Gold

Should Gold Producers Hedge Their Positions Through : Sales on Forward Markets? Purchases of Put Options? Sales on Spot Market? Forward Markets Assumptions 1. Producer has a known amount of Gold to sell in year ahead. 2. Effect on price is the same whether sold Forward or Spot Market. 3. None of us have knowledge of Future Price Trend. 4. Contange Market prevails in which Forward price premium is approximately equal to rate of interest.

Jan 1, 1983

By John C. Cook

There is pressing need for better means of exploring ground conditions ahead of mining. Exploration drilling has the drawbacks of high cost and a seriously restricted sampling zone. Traditional geophysical exploration methods including gravity, magnetic and resistivity techniques have been used with some success underground, but all give poor target delineation relative to range, since they depend upon minor distortions of a potential force field. Much greater ratios of resolution to range can, in principle, be obtained by employing electromagnetic or seismic radiation as the exploring agent. This is because propagation time delays can be used to measure range accurately, and to separate the small effect of a distant target from the much larger effects of nearer targets and of the transmitter. Seismic waves have long been used with great success in exploration for petroleum, and recent research on their application underground is promising. Electromagnetic (radar) waves have been very successfully used for detection and location through the air and outer space, and have also explored through polar icecaps more than a mile thick.l It is not generally realized that below the soil many rocks are also somewhat radar-transparent, and that radar can be used for exploring such rocks, once a quarry, a mine, a borehole, or other means of access has been opened. Radar waves are reflected by any boundary or object where they encounter a large change in electrical properties.2 The usual cause of such a change is a difference in moisture content. Radar waves passing

Jan 1, 1972

By Alfredo Valdivia, Jesus Schabib, Vojtech Gall, William Cao, Curt Cicileo, Andrew J. Thompson

"The East Side Access Project (ESA) involves the construction of geometrically complex underground structures including a large number of caverns and bifurcations. Initially conceived as dual lined structures with either traditional concrete or shotcrete final linings (SFL), construction economy, advances in concrete placement technology and scheduling among others led to a wide use of what is referred to as freeform or pneumatically applied concrete (PAC) for the construction of tunnel final linings. PAC is a method of applying concrete without using formwork, where a wet mix concrete is pneumatically installed to encase reinforcement to full lining thickness. PAC has been widely adopted at ESA well beyond initial expectations. The paper addresses the design and construction aspects of the PAC method and contrasts it to traditional SFL lining placement. The experience made provides guidance for future PAC and SFL applications. THE EAST SIDE ACCESS PROJECT AND USE OF FREEFORM CONCRETE The Long Island Rail Road (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodates New Jersey Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the New York City Transit (NYCT) Subway System and Metro North Rail Road. The construction includes mining and lining of new tunnels and facilities under Manhattan and Queens. The tunnels run from Queen’s Sunny Side Yard through the existing 63rd St. Tunnel, underneath Manhattan’s Park Avenue until termination at 37th Street. Differing types of tunneling methods and final lining systems are being used depending on the ground conditions, geometry and size of the excavation, site constraints and functional requirements. Mining of the Queens segment of the ESA Project involved soft ground tunneling by pressurized face tunnel boring machines, cut and cover construction, and conventional tunneling. The Manhattan segment of the ESA Project involves mining in hard rock by tunnel boring machines, drill and blast, and road header."

Jan 1, 2016

By L. Rintala, P. Latostenmaa, T. Kalliomäki, O. Forsén, I. Lehtiniemi, M. Lundström, J. Aromaa

Conductivity is a typical physico-chemical property that has a substantial effect on electrical energy consumption in the electrorefining process. The objective of this study was to examine the validity of regression models predicting the conductivity of industrial copper electrorefining electrolytes. The models were based on data measured with synthetic solutions on a laboratory scale. The variables included in the models were temperature and the concentrations of copper, nickel, arsenic and sulfuric acid. Both first-order and combined effects of the variables were investigated. The measured data were analyzed using MODDE 8.0 modeling and design software. The validity of the models was investigated by comparing the predicted values with tankhouse conductivity measurements taken at the Boliden Harjavalta Copper Refinery in Pori in Finland. During the tankhouse tests, the conductivity and temperature of the industrial electrolyte were measured, and the composition of the electrolyte was analyzed. The measured conductivity values were compared with the predicted conductivities calculated using the developed models. The conductivity model developed in this paper was shown to be more accurate than previous models and suitable for industrial use.

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By Gene Mattila

Each installed rock bolt costs in excess of 520.00. High cost in conjunction with the primary purpose of safety makes it only logical to install the highest quality anchors possible. Each bolt has designed support capabilities in axial, shear and fluctuating ground condition, if installed to manufacturers recommendations. The quality of anchor is not; however, only affected by material specifications, but by transportation, handling storage, installation procedure, machine performance and geology. The quality is not only affected by many variables, but reliability should be assured. Non-destructive methods of testing reliability are only available for several types of bolts.

Jan 1, 1985

By S. Alpay

Underground mining method selection (UMMS) is one of the most important decisions that mining engineers have to make. Choosing a suitable underground mining method to extract a mineral deposit is very important in terms of economics, safety and productivity of mining operations. In real life, UMMS is one of the Multiple Attribute Decision Making (MADM) problems and decision makers have always some difficulties in making the right decision in the multiple criteria environment. Analytic Hierarchy Process (AHP) and Fuzzy MADM (FMADM) are the MADM tools and can be used for the selection of the best underground mining method by considering the problem criteria. UMMSMADM is a computer program which is based on AHP and FMADM and it can analyze the UMMS problems and produce the best underground mining method considering different deposit shapes and ore bodies.

Jan 1, 2010

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996