Search Documents

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By Gregg E. Korbin, Patrick Hamilton

INTRODUCTION The Balsam Meadow Project, presently under construction for the Southern California Edison Company, is located approximately 55 miles northeast of Fresno, in the Sierra Nevada Mountains (Fig. 1). Major components of this project include an underground powerhouse for a 200 MW unit and a high pressure power tunnel/shaft. Site exploration [ ]

Jan 1, 1987

By E. Zahl, J. Whyatt, H. Lawson

The U.S. Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03 in April 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB P09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2013

By C. Tsiouvaras

Restoration of bauxite mining areas constitutes a difficult issue to address due to the destruction of the vegetation and soil decay of the excavated area. In this study woody species growth, in relation to altitude, heavy metal concentrations and mechanical texture of the underlying mining waste, were investigated. The research was implemented on restored sites of a bauxite mine in the Fokida Prefecture of Greece. These sites were located in three different elevations and the restoration took place in two phases, in 2001 and 1996. Heavy metals measurements showed some correlation among the different metals, whereas their concentration was also associated with plant growth parameters.

Jan 1, 2007

By Daniel L. Hanson

This paper presents case histories of the construction of four large diameter circular shafts using reinforced concrete ring beams as the primary internal support system. The case histories pertain to concrete ring beam systems which have been successfully used in shafts up to 130 feet in diameter and 75 feet deep. Soldier pile and lagging, and driven steel piling earth retaining systems using ring beams, are discussed together with the cost savings associated with using concrete ring beams. Soil conditions encountered at the case history sites are discussed together with the development of design criteria for each shaft. Instrumentation data obtained at one site are also presented.

Jan 1, 1987

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By Armando Correa de Araujo

Cationic flotation of quartz is currently utilized for the concentration of iron ores and for the cleaning of phosphate concentrates. The present work deals with depression of quartz in the presence of aluminum ions during cationic flotation. It was established-that aluminum ions depress the flotation of quartz with an amine, especially under neutral and very slightly alkaline conditions. Studies of adsorption of Al ions on the quartz surface as a function of pH correlated with depression of this mineral with an amine as collector. The presence of Al ions also enhanced the depressant action of corn starch on quartz The sodium salt of ethylenediaminotetra-acetic(EDTA) was found to be an effective complexing agent to supress the depression caused by aluminum ions.

Jan 1, 1984

By Olivia Perkins, Shawn Sismondi, Adrian St. John, Vicky Potts

"INTRODUCTION An inherent aspect of any tunnelling project is ground risk: how it is identified, quantified and managed throughout the various stages of a project. Early identification of these risks, such as adverse ground conditions or potential obstructions is crucial; however specific identification of all risks will inevitably be limited by the extent of the desk study, ground investigation and accuracy of as-built information available, particularly in a densely populated urban environment such as London with a long and varied history of development. It is therefore crucial to have suitable plans and procedures in place for dealing with potential ground risk scenarios if they occur during construction work to ensure the safety of the workforce and to protect nearby critical assets. A number of experiences of potential ground risk were encountered during the Sprayed Concrete Lining (SCL) works on Crossrail contract C300/410 which was constructed by a joint venture of BAM Ferrovial Kier (BFK). The C300/410 works, undertaken in the heart of London, comprised of over 2.5km of SCL tunnels for Bond Street and Tottenham Court Road Stations and the Fisher Street crossover, as well as two 6.2km TBM tunnel drives between Royal Oak and Farringdon. BFK appointed Donaldson Associates as their SCL designers for the works; together they were responsible for excavation stability up to the point of ring closure. Despite the majority of SCL tunnelling works at Bond Street and Tottenham Court Road being through the favourable medium of London clay, there remained areas of local geotechnical challenges. Some of these were expected from the outset, some became apparent as works progressed from records of other nearby excavation works, and some were only encountered during tunnel excavation. Being located in the centre of London meant that there always remained a possibility of meeting some form of obstruction from previous structures. However, identification of all potential issues prior to the commencement of the works was challenging and proved to not be entirely possible. Through a series of case studies, this paper documents incidents where obstructions or adverse ground conditions arose. These scenarios all had the potential to cause safety risks, impact the tunnel design and/or construction methods and ultimately add time and cost to the works. The paper discusses how these challenges were overcome which utilised in part, a progressive risk reduction cycle, feeding back knowledge gained at all stages of construction into the approach for undertaking the works. It also examines what could be done in future to further reduce the ground risk through early identification, communication, education and appropriate contingency measures."

Jan 1, 2016

By Robert Stefanko

The widespread and increasing use of electrical power for mechanized power has made a tremendous impact on the coal mining industry. It is probably the single most important factor influencing the productivity of a coal mine. In fact, as a part of a study of 62 coal mines in Pennsylvania and northern West Virginia, plus information that was obtained from other sources, it was possible to show a direct correlation between the rise in the use of electrical power and mine productivity, Figure 1. This increased power demand has not always been achieved through proper planning and a careful evaluation of all design parameters, many of which are not even recognized. The result has been increasing problems in power distribution and utilization establishing the need for scientific studies including considerable underground measurements. Because the cost of power for ton of coal produced is generally a relatively low value, inadequate attention is paid its distribution and utilization. Furthermore, a poor system of records and a lack of adequate measurements add further to a paucity of statistical evidence that would permit a rational analysis of overall power costs. However, the direct cost figure alone is highly deceptive; of much greater value is the indirect costs associated with the use (or misuse) of electrical power underground. Success in highly mechanized mining correlates directly with equipment utilization. Today's machines have tremendous potential capacities but profits are measured in terms of performance and not potential. Thus the reliability of electric motors is an extremely important factor for consideration and the effects of all parameters should be carefully evaluated. Thus while studies are continuing on the evaluation of primary and secondary mine electrical systems with interesting results, this paper will be limited to reporting on the results of a study of a specific motor application.

Jan 1, 1972

By P. L. Dunn

Automatic control of fine coal cleaning circuits has traditionally been limited by a lack of sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for on-line determination of ash content in fine coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73 ± 4% ash over a range from 65-90% ash. While this result is comparable to existing nuclear-based analyzers, the video-based system is only a fraction of the cost. The sensor is currently installed at the Middle Fork preparation plant owned by Pittston Coal Company.

Jan 1, 1997

By Valerio Violo, Antonio Raschilla, George Kafantaris

"The Cityringen project in Copenhagen, Denmark will form a new circular line in the city center and will consist of 21 new stations (17 + four transfer stations) and approximately 31 km (19 miles) of earth pressure balance (EPB) twin-bored tunnels.The new tunnels passed under the historical building of Magasin du Nord, McDonald’s and two pubs in the heart of the city with a minimum cover of about 4 m (13 ft).To minimize the movements, a complex system of compensation grouting and jet grouting soil treatment was performed. A detailed action plan between the parties involved allowed coping with the critical tunnel boring machine’s (TBM) successful passage.The Cityringen is an extension of the existing metro line underground Copenhagen and will include the City Circle Line, 15 km (9.5 miles) of twin tunnels looping around the city. The City Circle Line will form a new circular track inside the city center and will intersect the existing M1 and M2 lines at Kongens Nytorv and Frederiksberg stations, as well as suburban train services at København H, Østerport and Nørrebro. It will extend the Metro network to the Nørrebro, Østerbro areas and the central station at København H (Fig.1). The two new lines M3 and M4 will run on the same tracks, but the M3 will be a circle route running around the entire line, whereas the M4 will drive from the station to the north side of the city.The €1.5 billion design-build contract was awarded by Metroselskabet in January 2011 to the Copenhagen Metro Team (CMT), a joint venture (JV) between the Italian companies Salini, Tecnimont Civil construction and Seli SpA. Since the bankruptcy of Seli SpA and Tecnimont, Salini Impregilo now owns 100 percent of the JV shares. Seli Tunneling Denmark ApS, a subcontractor to CMT, was initially constituted as a Seli SpA subsidiary and, following the economic difficulties of Seli SpA, was acquired in 2015 by Salini Impregilo. Seli Denmark is in charge of the tunnels excavation and lining and owns the four 5.84-m (19-ft) diameter Seli/Kawasaki earth pressure balance machines."

Jan 5, 2017

By Robert L. P. Kleinmann

Mining has been a significant component of the Appalachian economy for about 200 years. The region continues to be adversely affected by the environmental degradation associated with these past activities. In addition, companies today are being denied permits at sites where acid generation appears likely. And air emission limitations at power plants now threaten the economic health of many moderate- to high-sulfur coal mines. Thus, when considering the environmental impacts of mining coal in Appalachia, it is important to consider abandoned and active mine issues. For example, abandoned mines generate acidic, iron-rich waters that adversely affect more than 6,400 km (4,000 miles) of rivers and streams in Appalachia. In contrast, operations that were active after the enactment of the 1977 Surface Mining Control and Reclamation Act (SMCRA) cause little water pollution. However, the costs of water treatment at such sites exceed $1 million a day. Even where water quality is not dimished, water supplies can be affected by mining. Subsidence-induced fractures can lower water table elevations or drain a surface stream dry. Subsidence can also cause damage to surface and subsurface structures.

Jan 1, 1995

By B. N. Conley, K. D. Luxbacher

"The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. The explosions that occurred at the Sago Mine in 2006, the Darby Mine in 2006, and the Upper Big Branch Mine in 2010 have caused a ripple in an otherwise steadily improving safety record. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reached a level of diminishing returns. Risk management, a safety approach that has been successfully applied in various industries including mining across the world, may provide a means to surpass the safety plateau in the U.S. RISKGATE is an Australian risk management program for mines that shows great potential for application in the U.S. However, fundamental differences between the coal mining industries in Australia and in the U.S. prevent direct implementation. This paper discusses aspects of the RISKGATE body of knowledge that require some adaptation before this program may be applied to the U.S. mining industry. INTRODUCTION The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reach a level of diminishing returns. In order to combat this stagnation in performance, a modification to the manner in which the mining industry approaches worker safety may be warranted. The implementation of a risk management based approach presents a potential method for not only surmounting the current safety plateau but also for achieving the long desired objective of zero harm. RISKGATE a risk management body of knowledge designed for the Australian mining industry that shows great potential for application in the U.S. This paper discusses aspects of the RISKGATE body of knowledge that require adaptation before implementation in the U.S. mining industry. These adaptations are based on differences in operating practices and governmental regulations. This discussion will focus on the three major U.S. risk areas of explosion prevention, ground control, and moving equipment."

Jan 1, 2015

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By K. H. McDaniel

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a U.S. Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of U.S. defense generated transuranic waste in bedded salt. In addition to its regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright © 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows ® application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System.

Jan 1, 1996

By Gerhardt A. Bennewitz

The mechanism shown here (Fig. 1) may not be all that it appears to be. To many of you it may look like a hopper car, a thing of mobility, in which you would ship coal, ores, limestone, or other bulk materials. It is approximately 50 feet long, 12 feet high, and can be placed on tracks which are on approximate 14 foot centers. But far too often in the past, and all too often today, this mechanism has been made to serve as an immobile storage box, with its primary role -- the transportation of products, seemingly incidental to the storage function. Our engineering training teaches us to conserve resources, despite some of the popular and misconceived philosophies being advanced these days. Those of you who work for companies with traffic departments know that they are always striving to reduce the price which is paid to move your mine products. Today, let's consider and analyze the ways in which the cost of transporting your mine products might be reduced, based on particular reference to coal. Bear in mind that in this context, cost and price are not necessarily synonymous. Until a few years ago, most coal and other bulk materials handled by railroads moved under standard tariff rules. These rules, which still exist today, provided transportation vehicles (railroad cars) for extended periods at no added price to the shipper or receiver. "Normal" free time rules would permit a car to be held for a maximum of 48 hours without charge; however, in the case of coal, there is a rule which, subject to liberal rules as to the

Jan 1, 1972

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

By M. E. Rossi, J. A. Bassan, J. B. Novillo

Sampling and geological models are the basis of recoverable resources models. They are pillars of mineral resources and reserves estimation, and what geostatistical methods for grade estimation should rely upon. The resource model is best estimated if geostatistical methods make good use of sound geologic models. Data collection from the original drill holes, including field procedures and the quality assurance and quality control (QA/QC) of those samples are pillar one of a resource model. The second pillar of the model is the good use of the logged geological information, resulting robust geological interpretations, and the corresponding three-dimensional models of those interpretations. These models are partly subjective and mostly conditioned by the quality of logging and the geologist’s experience. They are also conditioned by the quality of the three-dimensional models built, regardless of the modeling method employed, traditional or implicit. Grade estimation is more commonly done by applying some geostatistical method and using the two basic sources of information, data and geologic model. Multiple stages are involved in this process, and in all of them there are uncertainties and risks that have to be dealt with. Knowledge, understanding, interpretation, and management of the model’s fundamentals are critical, given that they directly affect its accuracy and predictive quality. The mitigation of related risks allows for the creation of opportunities, generating value and reducing the project’s uncertainty. This paper discusses some of the key variables, uncertainties, and risks involved in the resource modeling process, illustrating with specific examples; discusses possible risk mitigation alternatives, and proposes best practices to avoid or mitigate those uncertainties. Emphasis is placed on taking advantage of technological advances without ignoring fundamentals. INTRODUCTION In the area of mineral resource estimation, one alarming trend that these authors have observed in the past 20 years or so is that the care and diligence in checking the work as it progresses has generally diminished. This is, perhaps, an unintended consequence of the availability of new technologies and tools that attempt simplify and speed up the work involved. This has led to a more casual attitude towards checks and balances that have to be in place at any given stage of the process before proceeding to subsequent stages, as best practices dictate. To some extent, some of these aspects are covered in international standards for resource estimates reporting (JORC, 2012; CIM, 2010). But these are broad, and do not specifically recommend best practices to a level of detail that would have an impact on certain aspects of the process. There are numerous references in the geology and mining journals and conferences that discuss the consequences of poor recoverable resource models (Baker and Giacomo, 1998; Vaughan, 1997).

Jan 1, 2019

By T. D. MacQueen

Thank you Mr. Stevens. It's a pleasure for me to be speaking to this meeting of the Society of Mining Engineers of AIME this afternoon, and the Gypsum, Association is grateful for the invitation. A brief word about who we are: the Gypsum Association is the trade association for the gypsum industry - the manufacturers of gypsum board and lath a-d plaster. We have a membership of eight companies. These eight companies produce about 90% of the gypsum products manufactured in the United States ... closer to 94% actually. Our headquarters is in Evanston, Illinois. We have an east coast office in Washington, D.C. where the eastern manager handles technical and building code matters and maintains liaison between all of the government agencies and departments and our industry. We also have a west coast office in Los Angeles where our west coast representatives is heavily involved with the Uniform Building Code and ICBO. And then in the Evanston office our manager of technical and building code services, Herb Carlsen, bites his nails and loses his hair over these problems and various other projects that come in, such as conversion to metric and various other things. We also have a research associate at the National Bureau of Standards in Washington who is currently concentrating his efforts on the combustibility of building materials. His studies involve current testing methods, definitions, data analysis, and proposed new testing methods,.' It is anticipated that this program will lead to a better understanding of non-combustibility of building materials and systems. I mentioned that our members represent over 90% of gypsum products,' manufactured in the United States; it might be well to point out a couple of statistics about what that really means. According to the Bureau of Mines,

Jan 1, 1977