Search Documents

By T. Negeri

Flotation is the most efficient and preferred solid-solid separation method in mineral processing. However, enhanced production of high-grade concentrates at sufficiently high recovery still poses technological challenges to-day. A novel flotation method to produce final-grade concentrates from finely-ground ores in a single step is being developed and tested by CANMET. For the complex sulphide ores tested, grades are superior while recovery is considerably improved. Furthermore, concentrate production rates, at similar recoveries, are faster than for the conventional rougher-scavenger-cleaner configuration. This paper discusses the physical operating parameters affecting Cu-Zn flotation metallurgy.

Jan 1, 1995

By M. G. Ayat

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent upon the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1986

By Joshua Farmer, Mike Gianforte, Tao Jiang, William Gettings

The Two Rivers Water Reclamation Authority (TRWRA) in Monmouth County, New Jersey, is replacing its aging Pleasure Bay Interceptor (PBI) with a new 54-in interceptor in a 3,250-foot long 8 to 10-foot diameter tunnel and a new 50-mgd main pump station (MPS). A comprehensive phased geotechnical investigation was performed, including SPTs, CPTs and geophysics. A channel filled with soft marine sediments was identified. The tunnel is set in stiff to hard marine soil to enable using a less expensive open-face TBM. The thickness of tunnel cover under the channel is optimized through numerical analyses to avoid a deeper pump station yet maintaining tunnel stability with controlling seepage.

Jun 13, 2021

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

By L. Martin, M. Raffaldi, M. Stepan, D. Benton

The Office of Mine Safety and Health Research, Spokane Mining Research Division, is continuing its high-energy, high-displacement testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link mesh, welded-wire mesh and combinations of them. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can assist in interpreting the condition of installed surface support. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to better quantify the stability of installed shotcrete support.

Jan 1, 2016

By B. J. Timmons

Depending upon which of two letters describing the theme of the session I chose to honor, the subject choices because either one or three. They were: "Applied Research and Exploration and Discovery" or "Applied Research in Exploration and Discovery." The final choice; to partially ignore both of them. That minor difference in meaning may be appropriate here, inasmuch as very minor research/exploration differences may also have profound impacts on discovery. To further set the stage, I consider myself an Industrial Minerals geologist, and more specifically primarily associated with basic construction materials crushed stone and sand & gravel. My remarks will apply primarily to those materials. Therefore, when the discussion instructions included emphasis on beneficial aspects (to name a few): "drill target definition; elimination of ore potential; ore forming environments; alteration studies, and isotope analysis," problems became apparent. Evidently, and although this was a form letter, the drafters of that letter had no idea what was involved in research for a construction materials source. My task may be great.

Jan 1, 1995

By Edward C. Mabbs

U.S. industry must increase its productivity or lose its competitive position in the rapidly expanding and inter-dependent world markets. Recent improvements in material handling techniques and equipment, coordinated with production processes, provide one of the greatest opportunities to increase productivity. Successful managers must learn how to take advantage of these material handling opportunities to gain competitive position.

Jan 1, 1973

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have ben made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modelling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developped, which can be calibrated far ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables to predict the complete composite particle distribution, and is thus valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1985

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By R. B. Dunn

Whilst coalmining in the United Kingdom has been synonymous with longwall mining practice there have been changes in recent times which have enabled not only an extension in the length of the face to be worked but also in the ability to extract both thick and thinner seams. Additionally the industry has taken a positive view in the extension of retreat methods of extraction applied for different reasons both to particularly thick and specially thin seams. To permit development of a flexible programme to meet these diverse needs, it has been necessary to design machinery along with mining systems specially suited to these requirements. In reviewing current UK thinking special emphasis is made on the extraction of thinner seams generally of higher quality coal at moderate depths with a commentary on some recent results.

Jan 1, 1979

By Hou Xilun

Three production methods of rapid cold bonding and low temperature bonding pellets using sponge iron powder as a binder have been successfully developed. These methods differ from ordinary bonding method by no addition of salt and other catalyzers, no corrosion of equipment and no pollution of environment. Mechanism of pellet bonding is studied. Experiment shows that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the production of metallic pellets continuous and stable. These methods are substituted for traditional high temperature firing of oxidized pellets in direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved. Production cost may also be decreased. The production of cold bonding pellets does not need additional area.

Jan 1, 1980

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962

By Rodger C. Smith

The topic chat has been assigned to me ?Economic and Political Climate of the Potash Industry? is a function of two basic facts: 1. Potassium is absolutely essential to plant and animal growth. Along with nitrogen and phosphorus it is one of three major plant nutrients, the three nutrients required in largest quantities for plant growth. 2. United States is unequivocally an "have not" nation with regard to potassium. Quantity of potassium ores is limited and, more disturbing, the cost of production at all U.S. potash mines is marginal in comparison with the major producing countries, i.e. Canada and U.S.S.R.

Jan 1, 1983

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. It is also a major exporter of minerals. Canadian open pits are highly mechanized and use state of the art equipment and support technology. During the past few years significant productivity improvements have been achieved by taking advantage of larger equipment; in pit crushing and conveying; truck dispatch systems and electronic management tools. The most recent developments in Canadian Open-pit Mining are related to hydraulic transportation and the application of Global Positioning Systems. Mine planning is computerized; environmental issues are dealt with in all phases of planning; equipment modifications are pursued with vigor to keep them functioning in the hostile Canadian North.

Jan 1, 1999

By Eugene M. Trisko

Presentation Overview State-Of-The-Art Scrub/Switch Analyses > Allegheny Power System > PSI Energy UMWA Phase I Coal Interests > 16 Phase I Scrub Plant Coal Profiles > Coal Price/Emission Allowance Interaction Southern Company Case Study > 2+ Million Ton Phase II Allowance Purchases > 10+ Million Ton Phase I Coal Switch > Georgia PSC Proposed Fuel Price Cap > Shift/Avoid Georgia Scub Costs Through System Allowance Purchases

Jan 1, 1993

By S. Nickson, M. Grenon

Oriented borehole data provide the means to characterize a rock mass. In this paper, the geomechanical caving potential of a hard rock mine project is investigated. In particular, the influence of random joints to the resulting block size distributions is addressed. The implications of this approach in preliminary investigations on the choice of mining methods are discussed with reference to one site.

Jan 1, 2003

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By Alexandra P. Wright

A vital aspect of environmental impact assessment for surface mining operations is the determination of potential effects on water resources. This topic has been the subject of much recent concern, controversy and legislation. As increasing data become available regarding the types of hydrologic effects that may be anticipated, methods for safe guarding our water resources can be refined. In view of our current energy situation, the need to develop coal re- sources in a timely and economic manner is apparent. The challenge to the mining industry is to develop these resources in a manner that is also compatible with the beneficial use of water resources in mining regions. For this reason, thorough evaluation of the hydrology of potential mining areas in consideration of proposed mining processes and relevant legal criteria is essential. While pre-mining hydrologic investigations often suggest generalized potential effects, a more reliable method for evaluating specific potential effects is to establish and maintain a hydrologic monitoring program. Such a program must be carefully designed to suit the specific project and its location. This paper describes an approach for selection of criteria for designing a monitoring program for a proposed coal surface mining operation and gasification plant in southwest North Dakota. Woodward-Clyde Consultants (WCC), recently prepared an environ- mental impact report for the ANG Coal Gasification Company (ANG), a subsidiary of the American Natural Gas Company. The mining will be carried out by The North American Coal Corporation (NACCO). Preparation of the report provided the opportunity for the development of a sensitive and economical monitoring program which would function as a baseline hydrological data gathering network as well as act an an early detection system for hydrologic effects of the proposed mining.

Jan 1, 1975