Search Documents

By J. R. Montgomery, T. A. Phillips, F. Blackham, D. J. Adams

Underground water, whether it is a mine seep, in situ leach solu­tion, or a pollution plume, is difficult to track and monitor. Monitoring wells are costly to drill and may be placed in the wrong spot. This report describes a test of an electromagnetic technique to track acid water draining from the Midnite Mine near Spokane WA. The tests successfully mapped the path of acid mine drainage being collected at the mine from two seeps. Several small side branches flowing to smaller seeps and a mix­ing zone where relatively clean water mixed with the acidic water, were also mapped. The study has changed previous opin­ions on the flow of water through the site and will be used as a basis for future site remediation planning.

Jan 1, 1996

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, largescale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in Chifeng City, China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading. The physical model test results of SOSM and room-and-pillar mining (RPM) with a weak pillar were compared, and the failure process of the SOSM pillar group showed the characteristics of rapid and severe damage. The strength difference between a weak pillar and the adjacent pillars enhanced the stress rebalancing effect and extended the failure process of the pillar group. Similar to the SOSM pillar group with a low w/h ratio, some high-strength pillars can be used to avoid large-scale destabilization disasters caused by the synchronous failure of pillars.

Mar 8, 2023

By Rudy Rogers

When Gas hydrate formation rates have two steps: a nucleation induction step and an agglomeration step. Hydrate induction in distilled water is extremely slow because of lack of nucleating particles. Our laboratory found that synthetic anionic surfactants greatly improve both hydrate induction and agglomeration because the surfactant?s hydrophilic head absorbs water molecules and the hydrophobic tail absorbs hydrocarbon gas molecules, creating necessary nucleation sites. Vast hydrate deposits inhabit seafloors. What is the seafloor hydrate nucleating mechanism? We find that nano-particles of smectite clays (bentonite and nontronite) are hydrate-nucleating sites in sea-water-saturated, packed porous media, especially when trace quantities of anionic biosurfactants adsorb on the clay particles. Microbes and their bioproducts proliferate around seafloor gas hydrate accumulations. The seafloor microbe-mineral-hydrate synergy is explored in this paper. Keywords: gas hydrates, biosurfactants, crystal nucleation, smectites

Jan 1, 2008

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By John K. (Original by) Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 32.7 t (36 st) of water for each ton of coal produced, while bituminous mines average about 4.5 or 5.4 t (5 or 6 st). Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed of is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. It must be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1981

By İlknur Erol

The abstract highlights that hearing loss is an occupational disease caused by noise exposure in the workplace. The study investigates noise-induced hearing loss among miners in underground coal mines in Turkey, considering factors like occupation, age, and exposure time. The research employs logistic regression analysis to reveal the relationship between hearing loss and these factors. The findings suggest that occupational groups and duration of noise exposure significantly affect hearing loss. Miners in production groups and those exposed to noise for 10-14 years have a higher risk. The study concludes that age does not significantly increase the probability of hearing loss.

Mar 24, 2022

By M. S. Frasad

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the .various process options adopted on the bulk samples collected from the Minnesota River Valley area which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion, HGMS, and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota were briefly discussed.

Jan 1, 1990

By Viggo C. Bertelsen, David G. Hammond

LOCATION AND EXTENT OF BART TUNNELS The San Francisco Bay Area Rapid Transit District (BART) during the past six years has become the Owner of 23.5 miles of single-bore tunnels. The tunneling experience gained while working closely with our Engineer and Contractors in the design and construction of these major transit facilities provides a basis for our "Owners" viewpoint. The 23.5 miles of tunnels are divided into two categories. Fifteen and one-half (15-1/2) miles of tunnels were constructed in soft ground underlaying the downtown areas of San Francisco, Oakland and Berkeley. Eight (8) miles of tunnels were built in "hard ground" in the hills separating Oakland and Berkeley from Contra Costa County and in the San Francisco hills on the Mission Line. Location of tunnels within the BART system are shown on Figure 1. The tunnels comprise 15.7% of BART&apos;s 75-mile dual track system. Their 176 million dollar costs (excluding rail, electrification or ventilation features) are 12.4% of the system&apos;s total estimated cost of $1.4 billion. The tunnels constructed in soft ground were shield and boring machine driven with ground support provided by steel liner rings. The exterior diameter is 17 foot, 6 inches in the majority of tunnels; however, on two tunnels with a 500 foot radius of curvature, the diameter was 18 feet. BART awarded 14 contracts for soft ground tunneling. The work was accomplished under free air or compressed air depending upon the ground water and soil conditions, safety requirements, and considerations for protecting adjoining property from damage either from the de-watering operations or settlements due to excavation. The tunnel bores, except on curves, were normally parallel being spaced at 32 foot centers on the Mission

Jan 1, 1997

By B. J. Scheiner

The Bureau of Mines, U. S. Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. In field tests, phosphate clay waste has been dewatered from a nominal 2.5 percent solids to greater than 20 percent solids. In other field tests, coal-clay waste has been dewatered from a nominal 3 percent solids to greater than 55 percent solids, in addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12 percent solids to 40 percent solids.

Jan 1, 1983

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Mobile RAs have a limited ability to dissipate heat, and heat buildup can lead to a life-threatening condition as the RA internal air temperature and relative humidity increase. The National Institute for Occupational Safety and Health Office of Mine Safety and Health Research performed heat testing on a 10-person tent-type training RA and contracted ThermoAnalytics, Inc. to develop a validated thermal simulation model (TSM) of the tested RA. The TSM was used to examine the effects of the constant mine strata temperature assumption, initial mine air temperature (MAT), initial mine strata surface temperature (MSST), initial mine strata temperature at depth (MSTD), and mine strata thermal behavior on RA internal air temperature using 117 W of sensible heat input per simulated miner. For the studied RA, when the mine strata temperature was treated as a constant, the final predicted RA internal air temperature was 12.8°F lower than it was when the mine strata thermal behavior was included in the model. A 10°F increase in the initial MSST resulted in a 7.1°F increase in the final RA internal air temperature, whereas a 10°F increase in the initial MSTD yielded a 2.5°F increase in the final RA internal air temperature. INTRODUCTION Since 2008, the Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (1). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. NIOSH recommended an apparent temperature limit of 95°F in its 2007 report to Congress (2). In 30 CFR 7.504, MSHA has specified a maximum apparent temperature of 95°F inside an occupied RA (3). The apparent temperature is calculated using both air temperature and relative humidity (4). Calculations could be used to determine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, in order to simplify the problem, the mine temperature could be assumed to remain constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. OMSHR research has shown that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (5). Thus, calculations performed with the assumption that the mine temperature is constant would under-predict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, research has not been used to confirm that the mine air temperature is the appropriate basis."

Jan 1, 2016

By Paavo Eerola

In May of 1984, it was decided that Outokumpu Oy would design and build a new nickel flotation mill to process ore from the newly discovered Enonkoski mine in eastern Finland. Since there hart peen a number of successful process charges in the existing mills, the design effort included the study and incorporation of several new developments, including all-autogenous grinding, "flash flotation", lane cell roughing, large cell cleaning and a computer-based, profit optimizing, process control system. The paper discusses the background and results of those studies, and a description of the resulting mill which will begin production in 1986.

Jan 1, 1985

By R. J. Andreini

Solvent extraction is widely used in hydrometallurgical processing of uranium for purification and upgrading leach solutions prior to recovery of metal values. Conventional solvent extraction processing utilizes mixer-settler units to achieve mixing of the aqueous and organic phases. Use of mixer-settlers permits continuous treatment of feed, but the processing rate is restricted by the time required for phase separation after mixing. Because of the high-shear type mixing used in a mixer settler a portion of the organic phase becomes mechanically entrained in the aqueous resulting in loss of extractant. For this reason application of mixer-settler units is often limited by the settling area required for phase separation, especially for systems where high volume throughputs are desirable or necessary. Several alternatives to mixer-settler operations involving the use of column extractors have been proposed. Packed columns (1-2), in which organic and aqueous phases are fed countercurrently, utilize packing materials similar to those used in gas absorption or distillation columns. Extraction columns utilizing rotating(3-5) or reciprocating elements(6-7) to achieve mixing have also been developed. Van Dijek(8) originated pulsed columns, in which mechanical or air pulsing of the phases enhances the mixing in the vessel. Each of the above column processes involve varying degrees of mechanical complexity which may lead to operational difficulties.

Jan 1, 1975

By Julián M. Ortiz, Antoine Caté, Oy Leuangthong, Ilkay S. Cevik

Mineral resource classification relies on the expert assessment of a qualified person (QP) to determine which blocks of a 3D mineral resource model are classified as measured, indicated, or inferred. The decision is often based on a combination of quantitative parameters related to the estimation process and qualitative decisions based on previous experience or preconceptions not captured in the numerical model. As such, the procedure is subject to inconsistency, that is, blocks with similar qualities may end up in different categories, mainly due to the subjective nature of the approach. In this paper, we present a methodology to assist the qualified person in this task by clustering blocks with similar parameters and then classifying them into categories in a consistent and automatic manner that only requires the specification of a few hyper-parameters. The result is a consistent classification into resource categories comparable to the result of a classification done by a qualified person but fully consistent and generated in a short time frame. The procedure begins with repeatedly sub-sampling the block model to determine a distance matrix using an unsupervised random forest approach and then clustering the blocks using the associated distance matrix. Then, all the blocks in the model are classified using a supervised random forest approach, which gives a probability of belonging to each class. The initial class can be determined from the class probabilities. Support vector classification with a radial basis function kernel is utilized to smooth the boundaries between classes and define the final classification. An approach to tune the hyper-parameters of smoothing is provided. The methodology is demonstrated with two examples from two gold deposits. Results are comparable to the classification done by the project qualified person using conventional methods.

Aug 17, 2021

By Ward Sumner

The Jones Hill prospect is a Proterozoic age, volcanogenic, semi-massive to massive sulfide deposit. The deposit is located on the western edge of the Pecos greenstone belt in the southern Sangre de Cristo Mountains of northern New Mexico. The prospect is found in a block (West Block) of meta- igneous rocks, primarily diabase, metavolcanic rocks, and metasedimentary rocks (fig. 1). This assemblage is typical of lithologies found in the greenstone belt. Metamorphic grade is greenschist to lower amphibolite. The West Block is bound- ed on the west by Proterozoic age (1.7-1.4 b.y. by Rb/Sr), granitic plutons collectively called the Embudo granite, and on the east by Paleozoic sedimentary rocks, primarily sandstones, shales, and limestones of Mississippian and Pennsylvanian age. The mineralization occurs in a single horizon which has been overturned and cut into two blocks by a high-angle reverse fault (fig. 2). The mineralized horizon is found at the contact of felsic metavolcanic and rnetavolcaniclastic rocks with overlying intermediate metasedimentary rocks. The local stratigraphic sec- tion from bottom to top is as follows: 1) porphyroblastic quartz- sericite schist (originally a rhyolitic, subvolcanic intrusive); 2) quartz-sericite-chlorite-biotite schist (felsic metavolcanic and metavolcaniclastic rocks); 3) chlorite-talc-biotite-sulfide schist (altered felsic metavolcanic rocks); 4) carbonate-quartz-sulfide [ ] chlorite-tremolite-talc schist (mineralized exhalite); 5) quartz- chlorite schist (silicified tuff); and 6) amphibole-chlorite-feldspar- biotite schist (occasional mafic to intermediate metavolcanic flows).

Jan 1, 2013

By Velu Annamalai

In-situ uranium solution mining involves the injection of a lixiviant (leach solution) through appropriately placed wells into the underground ore zone. Upon contacting the uranium minerals, this solution will dissolve the uranium. The uranium containing solution is then pumped out of the wells into a processing plant where the uranium values are removed, typically in ion exchange columns, and the stripped liquor is recycled back into the field. The lixiviants may be acidic or basic. Where the ore zone mineralization contains appreciable carbonate, as in the South Texas fields, acid consumption would be excessive and the typical solution is ammonium carbonate bicarbonate at about 5-10 g/l and a pH of 7-9. Because the usual uranium minerals, uraninite or coffinite, contain uranium in the insoluble tetravalent state, it is necessary to add an oxidant to increase the valence to the hexavalent state where the uranium is soluble. Oxygen dissolved in the lixiviant has been shown to be quite effective for this purpose. It is also much more economical than other oxidants. Of concern is the possibility that (1) its solubility may or may not provide concentration levels adequate to give an economically attractive uranium level in the extracted liquor, and (2) the addition of oxygen in excess of the saturation level so as to increase the uranium grade in the lixiviant may cause gas blockage of the typical fine-pored ore formations.

Jan 1, 1981

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By Frank Pollard

The Australian coal industry over recent years has experienced the situation whereby exploration and mine development are moving into geographical areas where the coal seams have never been mined to any extent in the past, if at all, and particularly where there is no history of experience in preparation of these seams. Additionally, the demands have been such that the development of a mine up to production stage should proceed with minimum delay. This is a situation which is of some importance and concern, in view of the coal quality requirements now experienced within world markets which can only be met, in most cases, by careful preparation. Costs are such that the preparation plant should operate as required by the situation and with maximum efficiency, which means that laboratoty information of breakage and washability characteristics which are required for preparation plant design should be accurate and available as soon as possible, even to a certain extent during the progress of the exploration.

Jan 1, 1981

By Bruce H. Mason

The exploration for a commercially acceptable deposit of limestone is consid¬ered by many to be a relatively easy task; however, trying to locate a zone of high calcium limestone of economic thickness within a formation, which outcrops only in a narrow band varying in width from a quarter mile to ten miles, adds considerably to the normal problems experienced during an exploration program. The existence of varying glacial and karst features in the outcrop area intensified the problems encountered and complicated the interpretation of the economic value of the deposit. This paper highlights a recently completed five year exploration program during which approximately 3,900 acres of ground in seven civil townships were evaluated as potential sources of high-calcium limestone. Details are given with respect to the final site chosen and the methods used in determining the suitability of the site. This site exhibited many karat features and several methods were utilized to determine the effect of these features on the gross characteristics of the deposit. Aerial photography for both mapping and interpretation were utilized. Black and white panchromatic photography, black and white infrared and color infrared photography were flown. Resistivity, diamond core drilling and close-interval angering were used to supplement the information obtained from the aerial photography.

Jan 1, 1974

By D. Einarson, B. Strickland

The decision to accelerate development of Stillwater Mining’s East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and RailSystems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km(3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999