Search Documents

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By R. A. Metz, Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (1), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profitability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus minimum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12). Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-lowgrade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1992

By J. B. Knaebel

I have been asked to discuss the "Development of the Twin Buttes Mine for Production." This property, which is a large low-grade open pit copper mine about 25 miles south of Tucson, Arizona, was recently brought into production by The Anaconda Company under a long-term lease agreement with the Banner Mining Company. Since the scope of this paper is limited to the subject broadly indicated by its title I will confine discussion of historical, environmental and other general matters to a brief summary sufficient, I hope, to establish a background of those conditions which influenced our approach to the technical and economic problems that faced us at Twin Buttes. The paper deals primarily with our studies and activities related to the solution of these problems and with the resulting engineering and business decisions that were taken - decisions which culminated last September in the initial commercial operation of another major open pit copper producer unique and interesting in several respects.

Jan 1, 1970

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By O. P. Sinha, Biswajit Mishra, A. K. Mandal, Raj Kumar Dishwar, G. S. Mahobia, Ram ji Omar

Most of the mineral deposits found in North-East India remain unexploited due to inadequate knowledge on their status, economic viability, and requisite mining technologies. The aimof this study is to characterize the multimetallic magnetite mineral deposit from the Nagaland area in India. The quality of iron ore was evaluated to establish its suitability as a raw material for iron production. Detailed studies were conducted to establish the composition and properties of the samples. X-ray diffraction (XRD), X-ray fluorescence (XRF), electron probe micro-analyzer (EPMA), and petrographic microscopy techniques were employed in the investigation. Shatter and tumbler test was performed for analyzing the mechanical properties of the ore. XRD studies indicated that magnetite is the major mineral with low amounts of martite, maghemite, and quartz. XRF/EPMA results indicated that magnetite contains 35–65 wt.% of iron and 1–5 wt.% of chromium. It also confirms the presence of Ni and Al up to 1 wt.% and Si up to 6 wt.%. Chromite-rich ore contains up to 30 wt.% Cr and 15–20 wt.% of Fe.

May 10, 2021

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By I. WILKOMIRSKY, J. BECKER, F. Parada

Purification of molybdenite concentrate from copper concentrates was performed by sulfation. The sulfation of molybdenite concentrates was carried out with pure sulfuric acid (> 96%) at 160–190 °C to study the influence of the reaction temperature and reaction time on the residual copper in the molybdenite concentrates. A purified concentrate with less than 0.1 wt% copper and low levels of other metals were obtained. For up to 7.1 wt% copper, the conditions required are a temperature of 190 °C, a reaction time of 14 h, and a moly/acid weight ratio of 1/1. Furthermore, several designs of sulfation reactors were evaluated in order to obtain the desired level of copper in the product and to analyze the influence of the operational and design parameters on the reactor dispersion number (Le). The basic design for an 80-t/day plant fed with 4 wt% copper molybdenite concentrate requires five backmixed reactors in series, each measuring 8 m3, operating at 190 °C and with a reaction time of 10 h. The reactor must be protected against severe corrosion by the hot sulfuric acid with either Teflon, glass or ceramic.

Jun 14, 2022

By John P. Weir

The coal industry is ever changing and complex. This article discusses some problems that must be faced and their projected economic effects. Coal's dominant market is for electric power generation. While growth rates in the 1980s will be nominal compared to historic growth rates, such growth will be substantial in absolute terms because it comes from a very large base. Higher growth is expected in the 1990s. History When looking toward the future, an examination of the past is helpful. Figures 1 and 2 present production and consumption statistics (expressed in short tons) on bituminous coal and lignite in the US from 1945 onward. After an all-time peak of 572 Mt (631 million st) in 1947, total production dropped to 356 Mt (392 million st) in 1954. Sustained growth in total production did not begin until the 1960s. Coal production from under-ground mines declined from more than 400 Mt (440 million st) in 1947 to about 295 Mt (325 million st) during 1965 to 1970. A further decline ensued until a strike in 1978 reduced production to only 218 Mt (240 million st). Underground mines produced 283 Mt (312 million st) in 1983. Coal production from surface mines has increased steadily since the early 1960s. While some of this increase has come from mines east of the Mississippi River, most has resulted from surface mines developed in the West. Production from surface mines west of the Mississippi River was 224 Mt (247 million st) in 1982. Total coal production from under-ground and surface mines, other than Western surface mines, continues to approximate levels of 40 years ago. In spite of several wage increases, increasing productivity in surface and underground mines enabled the coal industry to hold the average value f.o.b. mine to about $5.50/t ($5 per st) from the end of World War II to 1969. Under-ground mine productivity peaked at more than 13.5 t (15 st) per man-day in 1969. The Coal Mine Health and Safety Act of 1969 was a major factor in underground productivity declining to 7.6 t (8.4 st) per man-day in 1978. However, pro-

Jan 7, 1984

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By Larry Powell

Rend Lake is an Army Corps of Engineers reservoir located in Franklin and Jefferson Counties in south-central Illinois. The lake consists of 20,000 acres of water and 19,000 acres of public access land. The site attracts over two million visitors a year and is surrounded by campgrounds and other recreational facilities. The lake overlies the largest tonnage of low sulfur coal in the state. Coal is being removed beneath the lake from five mines operated by three coal companies. Currently high extraction mining operations are approaching low-lying, environmentally sensitive, and high-use recreational areas. Advanced planning to maximize coal extraction and minimize potential effects of subsidence requires the development of procedures to assess the impact of high-extraction mining on the land use of the area. The Bureau of Mines, the Corps of Engineers, and the coal companies have initiated research to assess the following proposed planning steps to ensure the maximum recovery of the coal resources while minimizing impacts to surface land use: 1) Establish a dialogue between the surface and mineral owners; 2) develop a geographic information system to aid in assessing existing land use and potential changes; 3) assess the potential effects of subsidence on drainage, wildlife habitats, and changes in land use prior to mining; 4) coordinate the mining displacements with surface activities to minimize disruption; and 5) develop appropriate mitigation plans before mining occurs.

Jan 1, 1986

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1987

By David G. Thompson

There are basically two commonly used methods of drying washed coal. They are mechanical drying (sometimes called dewatering) and thermal drying. The common methods of mechanical drying are by using vibrating screens, cross flow screens, sieve screens or Vor-Siv, vacuum filters and centrifugal dryers. With thermal drying, the common types include direct fired fluid bed, rotary drum, flash or suspension, vertical tray or cascade continuous carrier or vibrating fluid bed dryers and hollow screw dryers. In the past, it has more or less been a general rule that any time the total product is being washed, both mechanical and thermal drying was required. The reason for this was that a product moisture of 3 to 4% was required and thermal drying was and is the only practical method by which this can be accomplished. With the advent of air pollution controls and the ever increasing concentration on dust elimination, a 3 to 4% moisture product is no longer practical in either the preparation plant or in the processing plants which utilize the coal. Under the new standards, it is desirable to have a product with a 6.5 to 7% surface moisture. With this moisture range, dusting, due to handling, will bc kept at a minimum.

Jan 1, 1975

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

Coal fly ash and flue gas desulfurization (FGD) sludges can be returned to mine pits, fills and revegetation zones in Virginia by regulation if (and only if) a positive beneficial use can be shown. Utilization of alkaline fly ash for control of acid drainage from pyritic coal processing waste piles, and use as a soil amendment for revegetation, are the two dominant beneficial uses proposed over time. Both applications must be controlled by the basic chemical properties of the ash proposed for utilization. Currently, public concerns over long-term As and Se leaching from various applications are increasingly driving regulatory options for mine site utilization. Many fly ash materials are relatively low in inherent alkalinity or neutralizing ability, and certain ashes are actually acidic. Failure to add sufficient total alkalinity will result in strong acidification of the ash utilization zones, stripping heavy metals like Mn, Zn and Cu from the fly ash matrix. Similarly, if alkaline ash is loaded into non-acid forming coal wastes at high rates such that leachate pH is > 9.5, significant leaching of As and Se has been documented in large scale laboratory leaching columns. Utilization of fly ash and FGD as a mine soil amendment for revegetation is based upon combined liming and water holding capacity benefits, however, levels of soluble salts (primarily sulfate and borates) limit one-time application rates to 100 Mg/ha or less.

Jan 1, 2006

By T. McDonald

Test work indicated and plant operation has since confirmed that SAG milling is a viable option for INCO's Sudbury Operation milling rationalization project only if pebble crushing is included in the SAG/ball mill circuit. Throughput increases more than fifty percent with pebble crushing incorporated into the comminution process. The finer product of high speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems.

Jan 1, 1992

By J. J. Peshel

As per the current conceptual design presented by the Department of Energy, the exploratory shaft facility (ESF) becomes a part of the repository if the Yucca Mountain site is found suitable for repository development. Therefore, the design of the ESF should be compatible with the performance requirements for the repository. The construction methods selected should limit to the extent practical, the degree and the extent of damage to the surrounding rock mass. The ESF construction and operation should be compatible with the site data gathering activities, such as geological, thermomechanical, hydrological and geochemical testing.

Jan 1, 1991

By Randy Ynchausti

ERIC GUTIERREZ, Knowledgescape: Our next speaker is Randy Ynchausti. He's the director of development, Knowledgescape systems division, of EIMCO Process Equip- ment Company. The title of Randy's talk is "An Expert Control System for Phosphate Beneficiation." RANDY YNCHAUSTI: System integration. How does the systems integrator survive when caught between plant engineers, plant management, and third-party engineering firms, and stay within the budget of the corporate goals? I'm not sure that anyone knows how to do all of that on one project. Results are critical when we talk about how systems integrators work with operating people, how the operating people want systems integrators to work with them, and how both groups work together so that at the end of a project, you have been provided with solutions that meet your needs and solve your problems at a fair price. How does the integrator's role change when working with different types of professionals, such as plant managers, plant engineers, engineering firms, or other system integrators? Finally, what is the dynamics of people working with machines and providing services and solving needs? The average number of employees per pound of copper processed has decreased significantly during the past 15 years. I would dare to generalize and say that the average number of employees per whatever unit of measure we have in whatever industry we work in has decreased over the last 15 years. From a system integrator's perspective, there are some clients who lack a bit of internal expertise as corporate downsizing occurs, and that's one reason why we go out to system integrators or third-party vendors and buy things from them to solve our problems. Downsizing really amounts to savings, but more than that, I think Brian expressed this and I agree with him, it also amounts to a cost. Unfortunately, most of us count the savings and none of us count the cost in that approach. It's easy to count the savings, which is one reason why we count it so quickly. Maybe that also accounts for why we set our pencils down so quickly after we get that dollar value. Maybe we should pick that pencil up every once in awhile and refigure the expense, the cost to us, and determine what we're going to pay during the next year or two or three in losing that expense, or that staff. A broad experience base accumulated over projects at various plants helps system integrators to provide services to clients. This experience enables the system integrator to

Jan 1, 1998

By Craig M. Sams

Matching mill? drives to mill power draws is a relatively new practice with the introduction of variable speed drive arrangements. Semi-autogenous grinding (SAG) mills are the focus of this paper as ball and rod mill characteristics are easily charted as charge loading and speed change. In addition, a look at types of drives available in the market and mechanical ratings is outlined to match the specifics of each drive.

Jan 1, 1991