Search Documents

By M. Szatkowski

The studies conducted by Laplante and coworkers (1983,1984) with flotation of galena and quartz, showed that the rate of flotation reaches a maximum value for a certain intermediate value of the air flow rate. A similar, though less pronounced, effect of the air flow rate on the selectivity was also observed. Luttrell and coworkers (1985) showed that the size of air bubbles has a significant effect on both rate and selectivity of coal flotation. These two studies used flotation tests in which no froth layer was formed. This note describes effects of the air flow rate and bubble size on the rate constant and selectivity of coal flotation, using a mechanical laboratory machine with a froth layer allowed to form. Experimental A raw, dry ground Illinois coal was used in flotation tests. The size distribution and ash content of the samples are : Particle size (µm) Weight (%) Ash (%) +600 4.30 41.7 600/200 43.05 19.0 200/74 22.25 16.0 - 74 30.40 24.0 average 20.8 No. 2 fuel oil with a concentration of 200 g/t of feed and M.IBC with concentrations of 11, 22, and 33 mg/L of pulp (128, 256, 384 g/t, respectively) were used as flotation reagents. Tap water with a natural pH of 7.0 to 7.8 was used throughout the tests. No other reagents were used. The starting concentration of coal in the pulp was 86 g/L. A standard flotation machine with the pulp volume of 5 L was used in experiments. Three different air flow rates were employed, resulting in three air escape velocity values of 14, 30, and 70 cm/min. The air escape velocity (AEV) was calculated as the ratio of air flow rate (Qa) to the slurry surface (Ss) in the machine. For a comparison, the upper limit of air escape velocity values used in commercial size flotation machines is between 70 and 100 cm/min (WEMCO, 1983). A machine consisting of a generator of fine bubbles and a separatory column, described elsewhere (Szatkowski and Freyberger, 1985), was used for some tests where bubble size lower than that generated in the standard machines was required. Prior to a flotation test, a batch of coal was mixed with water in the flotation cell for at least 10 minutes to ensure that all coal was thoroughly wet. Then the specified amount of fuel oil was added and the pulp was conditioned for five minutes. The specified amount of MIBC was added 15 seconds before the end of conditioning. After air flow was opened, flotation products were collected for 0 to 30, 30 to 60, and 60 to 120 second intervals. Content of the combustible material in samples was determined by subtracting the ash content from 100%. A photographic technique was used to determine initial distributions of bubble size generated by the flotation machines. Bubbles generated in water containing the prescribed amount of the frother but no solids were photographed against a black background. The average diameter and standard deviation were then calculated for each set of flotation conditions. The method gives results reproducible within k 5% of the average bubble size. Table 1 contains information about the measured bubble size distributions expressed by the average bubble diameter (Db) and the standard deviation ( SD ) . Results and discussion The general formula for calculating the flotation selectivity is: o = recovery of coal/recovery of ash (1)

Jan 1, 1988

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By C. Bazin

The fundamental error associated to the sampling of heterogeneous ore particles is unavoidable and can only be minimized by an adequate selection of the sample mass and/or size reduction of the sample before division into sub samples for testing or assaying. The preparation of ore batches to carry out the mineral processing evaluation of an ore is a sampling process. The fundamental error associated with the division of the ore into batches is responsible for the differences in the composition of the batches. This paper attempts by various means to assess the reproducibility of the gold content of test batches prepared from a gold ore sample. The results of the investigation shows that for fine gold grain sizes the variability in the composition of the batches is less than that predicted by Gy?s formula and that the gold grain size is a strategic information in the assessment of the gold content variability of test batches.

Feb 23, 2014

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By Malcolm Wills

Boddington Gold Mine commenced operation in 1987 with an initial production of 3.0 Mt/y at a grade of 3.5 git. Head grade has reduced over the life of the mine and the major response to the drop in grade has been to increase mining rates and increase plant throughput. A capital expansion was carried out in 1996 increasing the throughput to 6.0 Mt/y and since that date tonnage has been increased without major capital expenditure. BGM's current mill throughput is 8.77 Mt/y ( 1999). In 1999 the combined basement plant and direct leach plant processed 8,770,055 tonnes to produce 233,507 ozs or 7.262882 tonnes of gold at an average head grade of 0.83 git. With grades of 0.83 git, and gold price at record lows, $US251.95loz in August 1999 or $A393.67loz it has been necessary to make and maintain major cost savings to remain profitable. Boddington Gold Mine has achieved this by a number of steps including a productivity study by outside consultants.

Jan 1, 2000

By C. L. Schneider

The problem of predicting the liberation spectra produced by a closed continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population balance model equation. The latest and certainly most significant progress made in this area is the solution proposed by King (1990), which requires one textural parameter that can be measured directly from the ore being studied. The main advantage of King's solution is that it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured, as required by the existing conventional solutions. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Milm diagram (Andrews and Mika, 1975). This has never been measured for any ore. The characterization of the internal structure of the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize, monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one-dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1994

By S. H. Seyedein, Hamed Tavakkoli, Mohammad Reza Aboutalebi, S. N. Asharafizadeh

The liquid–liquid extraction behavior of lutetium from different acidic solutions was investigated using two extractants, D2EHPA and PC88A, in kerosene. Lutetium extraction reactions with D2EHPA and PC88A from HNO3 and H2SO4 solutions were chemically and thermodynamically analyzed. It was found that each Lu cation was complexed with six monomers of the organic extractant and released three protons. Simultaneously, the Lu cation was instituted in the P–O–H group of the extractants. Thermodynamic analysis of reactions between extractants and acidic solutions showed that the D2EHPA-HNO3 system is the most favorable for extracting lutetium. It is noted that the calculated equilibrium constant of the reaction in this system was approximately six times larger than that of the D2EHPA-H2SO4 system. However, the value of the equilibrium constant for the D2EHPA-HNO3 system was evaluated to be approximately 200 times greater than that of the PC88A-HNO3 system. Therefore, one can conclude that the extraction behavior of lutetium is more influenced by the extractant type than the solutionmedium. The synergistic effect of different mixtures of extractants on the solvent extraction of lutetium was also examined, and the highest synergistic factor was obtained for a binary mixture of PC88A:D2EHPA at the ratio of 4:1 for both aqueous solutions.

Mar 15, 2021

By Deepak Malhotra

INTORDUCTION Mining operations are unique In that they handle large volumes of water (millions of gallons) daily. The water contains dissolved metals, processing chemicals, organics, and other contaminants, There are several sources of water contamination at mine sites: mines, mills, tailings ponds, and Industrial/utility complexes. Utility waste water generally represents a very small portion of the total process water utilized in a normal milling operation and hence will not be addressed in this paper. Mine drainage can represent a significant amount, thus having an Impact on the recovery of metals, especially In Industrial minerals operations, and may have to be treated separately. The National Pollutant Discharge Elimination System (NPDES) effluent limits are becoming more stringent, thereby requiring mining operations to treat process water prior to discharge to the environment. The general trend Is to move toward a closed-loop waste system and treat only that small fraction of process water which Is to be discharged to public lands. The following section discusses the reasons for waste water treatment and the existing and emerging technologies for meeting NPDES effluent limits. REASONS FOR WATER TREATMENT Due to the diverse nature of the mineral Industry, process/waste water contamination problems as well as processing flowsheets are site specific. However, certain generalizations can be made specific to processing of different minerals: • Acid mine drainage Is a problem at sulfide/coal mines. • Cyanide contamination of water Is a problem at gold processing plants. • Organics can be a problem at mines using flotation oils. • Tolling ponds are generally acidic at sites processing industrial minerals such as silica sand and feldspar. The cost for water treatment Is viewed as an added cost of production. Hence, large mines are moving toward dedicating personnel to management of water resources in order to minimize waste water for treatment. Very often, mines having closed-loop water systems will treat waste water for reasons other than meeting NPDES regulations. These Include situations where process requirements dictate use of high-quality water for separation of minerals, neutralization of acid mine drainage water, and portable water for the mill. WATER TREATMENT TECHNOLOGIES Water treatment process has to be cheap and simple because It has to process large volume, and It does not directly add to the bottom line, namely revenue. The water treatment process development has to be site specific because the contaminants In the water vary from site to site. and discharge limits for water vary from state to state. The current technologies for wastewater treatment have been divided Into the following three areas: • Removal of heavy metals • Cyanide destruction • Scale control A brief summary of the current technology In each area Is discussed below. Removal of Heavy Metals The physical and chemical processes for heavy metal removal are summarized in Table 1. The most common and cheapest approach has been the precipitation of hydroxides at high pH followed by sedimentation and thickening of solids. The remaining solids can be removed by filtration. The pH is adjusted back to neutral, and the water Is discharged. This process is most commonly used wastewater treatment technology in the mining industry. The basic processes can be modified by combining other operations in order to meet the objectives of the specific site as illustrated In the following examples: • AMAX's Mt. Emmons treatment facility uses Lectro Clear® process where the precipitated solids are removed by electroflotation. • AMAX's Climax Mine water treatment plant used Ion exchange columns to meet the discharge limits on molybdenum.

Jan 1, 1992

By A. L. Coello Velázquez

The subject of this paper is particle population balance models (PBM) that describe mineral impact crushing behavior; it is mainly concerned with the selection and fragmentation distribution function due to their importance in this context. The data obtained by Datta (1999) by applying impact pendulum testing to single limestone particles, used by Austin (2002, 2004a and 2004b) to obtain the principal parity of fragmentation functions, were processed in order to compare them with the results of other authors, such as Nikolov (2002 and 2004) and Vogel and Peukert (2003 and 2005) so as to increase knowledge of impact crushing. From this data it has been possible to obtain the performance models of the principal parameters of fragmentation function, thereby reducing the number of experiments necessary to model the impact crushing process. The authors also propose a simplification of the selection function model posited by Austin (2002).

Jan 1, 2011

By George J. Allen, Laura A. Allen

Introduction This section of the text presents a general review of the different types of concentrate marketing contracts. Too often the marketing strategy is ignored in the design phase of the project and the producer is left to the mercy of the buyer. Many items such as concentrate grade, impurity levels and moisture content of the concentrate my enhance, or severely restrict the producers ability to make a profit it. Close attention should be paid to the design of the concentrator which can improve the quality of the concentrates, thus the ability to increase the rider of potential buyers can be enhanced. Difficult at best, is the position of the miner who only has one outlet available for its production. Obviously, the trade offs must be evaluated. For example, concentrate grade vs recovery and grind/filtering capacity vs moisture of the concentrate all must be weighted against freight cost to a potential buyer. In addition, the above considerations must be weighed against the capital cost to the miner. This chapter is intended to highlight important articles that are included in short and long term agreements and to give a new miner/producer some insight into hat my or my not add value to the product. Unless the miner sells the product directly to a consumer such as a gold, or silver producer, or to a large enough operation that has a totally intergrated system to make a finished product, most miners are forced to sell to buyers who ultimately will refine and market the product. Types of Contract Agreements There are many types of contract agreements just as there are colors in the rainbow, however, most contracts fall into three basic categories. (1) Smelter Schedules: Designed for the small producer, the odd lot of concentrate, smelter flux and precious metal ore. Albeit custom smelters are becoming fever by the day, because of pollution control requirements and financial difficulties, most remaining custom smelters have a smelter schedule. A smelter schedule is a posted list of charges and conditions that the smelter will buy material from a seller. Smelter schedules exist for copper, lead, zinc, silver and gold (Handbook for Small Mining Enterprises, Montana Bureau of Mines). (2) Short Term Custom Contracts: Large mine producers frequently use Short Term Contracts where the seller has the buyer frame a contract that is tailored to the sellers’ production. The short term contract my be as long as one year. A spot sale qualifes as a

Jan 1, 1986

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By B. J. Arnold

Prior laboratory work has demonstrated -that much of the fine ash-forming minerals entering a flotation froth are there as a result of water carry-over from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 300 cu ft WEMCO flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent of solids in the froth). Reagent changes which result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1990

By Yubo Tu, Lianqi Wei, Tianyi Zhao, Peiwei Han, Zhengchen Li, Shufeng Ye

The effect of oxygen partial pressure on the volatilization percentages of valuable metals from iron-rich pyrite cinder by chlorination-volatilization method using CaCl2 as chlorinating agent was investigated in this study. The volatile products were collected directly and analyzed by X-ray diffraction. It was found that there were CuCl2, CuCl, PbCl2, and ZnCl2 existed in the volatile products. Au and Pb volatilization percentages were almost not affected by oxygen partial pressure. Both Cu and Zn volatilization percentages were negatively correlated with oxygen partial pressure when CaCl2 dosage was no more than 4 wt%, and almost uncorrelated with oxygen partial pressure with a CaCl2 dosage of 6 wt%.

Dec 19, 2023

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By Laszlo Valentyik

Heavy media separation (HMS) is one of the most widely used gravity methods in the mineral industry. The feed is separated, according to the specific gravities, into two products; float (light) and sink (heavy) particles. The universal acceptance of the process is due to simplicity, efficiency and robustness for ease of control. However, if optimum separation is desired during the operation of heavy media plants, a delicate balance of a number of variables is essential. Among the variables, the two which are generally the most frequently checked and controlled are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media. The medium is generally made up of finely ground ferrosilicon, magnetite, galena, shale, quartz sand, clay contaminants and water. The frequently present clay in the medium acts as a stabilizing agent, since the coarse heavy medium solids (called media) would quickly settle if they were mixed only in water. Clay concentration of the medium varies between 3-7% by height (1,2). Although clay is essential for reasonable media stability, clay concentration greater than 7-8% imparts too high a viscosity to the medium, and the feed cannot accurately stratify and therefore separate into the required products. To be on the safe side, plant operators clean the medium from most of the clays, and would rather work at a lower stability than have a very viscous medium on their hands. The most recent advance in the area of consistency control rlas made by the introduction of atomized (spherical) ferrosilicon (3). This extended the upper limit of the use of ground ferrosilicon from 3.3 to approximately 3.6, broadening the range of the optimum operating conditions. A viscosity control method was also worked out by the use of low cost additives which lower viscosity while retaining a favorable low setting rate (4). Recently (5) polymers have been successfully used in oil well drilling muds then the requirements were mainly to suspend and transport cuttings during the periodic shutdowns and dril1ings respectively. The rheological properties of these polymer suspensions are such that they present an infinite viscosity to

Jan 1, 1971

By Gary Brieley

Until well into the 20th century, most construction work was performed under the auspices of a master builder or in a manner that would be described today as design-build. In addition, many civil engineers served as ?interns? under the tutelage of a master builder in order to learn how to design and construct a certain type of structure. This was certainly the case for tunneling projects with various individuals having been identified as tunneling experts as a result of successfully completed projects The master builder approach began to change in the early 1900s to a model that would be referred to today as design-bid-build. A design-bid-build approach to project procurement gives the owner more control over the final product and al-lows the contractor to know exactly what is expected of them before the work is constructed. As a result of this transition in project procurement, civil engineering schools placed a greater emphasis on the training of ?design? professionals. This article will document how the training of tunnel design professionals progressed within the United States. Although it is difficult to generalize about the hundreds of tunnels that were constructed in the first four decades of the 20th century, there is one project that stands out as having resulted in a university program related directly to tunneling and that is the Chicago Subway. During a visit to the United States in 1938, Dr. Karl Terzaghi met a student named Ralph Peck who was then studying at Harvard University in a pro-gram established by Arthur Casagrande. Shortly thereafter, Terzaghi traveled to Chicago for a lecture and was asked to consult on the Chicago subway project that was then under construction. The Chicago subway was being constructed in clay, and the owners were worried about possible settlements to nearby buildings. Terzaghi asked Peck to serve as his field engineer for that project. Thus was established one of the most productive relationships in the history of civil engineering in the United States. Peck, who would become Dr. Peck, moved to Chicago in 1939 to participate in an extensive research project that con-tinued until subway construction was halted in 1941 because of World War II. During that time, the cost of subway construction in Chicago was reduced substantially as a result of Peck?s observations and Terzaghi?s recommendations. In fact, it was reported that subway construction in Chicago cost less than one-half of similar projects in London even though the clay in London is considerably stiffer compared to Chicago. Upon the completion of his work on the Chicago Subway, Peck accepted a professorship with the University of Illinois in Champaign/Urbana.

Jun 1, 2010

By James E. Monsees, Wayne A. Carbiener, Michael R. Wigley

This paper illustrates an approach to quantitatively document the degree of technical conservatism to be incorporated into the design of a waste isolation system in bedded salt. It is anticipated that for an actual repository site the key performance constraints and/or design bases identified in this paper will be reviewed, and modified or supplemented as required. Ultimate acceptance of a repository will be dependent upon scientific peer input and scrutiny of the demonstrated conservatism inherent in each specific repository site and design.

Jan 1, 1981

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977

By P. Zhang

A 1989 FIPR characterization study of the future phosphate resources in Florida showed that MgO would be a problem with both the pebble and concentrate as phosphate mining moves deeper. Since the ratio of concentrate to pebble will become higher and higher in the future, reducing Mg content in the concentrate by a small margin would allow blending of a large portion of the high-dolomite pebble. This research was conducted based on that logic. The following six approaches were tested for reducing MgO content in the flotation concentrate: (1) Adding a dolomite depressant in the rougher flotation step; (2) Dolomite flotation on the rougher concentrate with and without grinding; (3) Dolomite flotation on the cleaner concentrate with and without grinding; (4) Scrubbing the flotation feed; (5) Scrubbing the rougher concentrate; (6) Scrubbing the cleaner concentrate. Successful methods include adding a dolomite depressant in the rougher flotation, dolomite flotation on the cleaner concentrate with grinding, and scrubbing the cleaner concentrate in quartz sand. These techniques could reduce MgO content in the final concentrate by 20-40%. The flotation process could achieve a concentrate with the lowest MgO content, but it is the most expensive approach. Adding a dolomite is inexpensive and easy, but the effect is limited. Overall, scrubbing may be the most promising technology for this purpose.

Feb 23, 2014