Search Documents

By C. D. Litton

This paper describes two new gas diagnostic techniques which have been used successfully to determine: 1) the combustion status of underground mines which have been sealed due to fire (Littol1 Ratio); and 2) the location of fires in abandoned, underground mines or waste banks (Kim Ratio). The Litton Ratio makes use of the rate of change of CO, calculated on both an air-free and methane-free basis, from mine gas samples and compares these values with those expected from a normal, combustion-free environment. The Kim Ratio uses the concentrations of total hydrocarbons, C2 ?C5, less the methane, to arrive at ratio values which increase as combustion intensity increases. The details of these two new techniques, their application to real situations, and their limitations will be discussed.

Jan 1, 1989

By W. C. Yates

Lack of visibility from large, open-pit haulage truck cabs has become a serious safety problem. Anaconda conducted a research program to develop a low cost system to alert haulage truck operators to small vehicles present in blind areas. Several systems were developed and tested. As open-pit haulage truck size has increased, so has the size of the blind areas. Mine utility vehicles, pickup trucks, and cars are concealed within these blind areas and become safety hazards. Figure 1 shows the typical blind areas of a 136 t (150-ton) haulage truck. The areas of greatest concern are at the rear center and front right corner of the truck. In these "no visibility" areas many small vehicles have been crushed by large haulage trucks at various mine sites. In most instances, the occupants escaped the vehicle before it was destroyed. But injuries and death have occurred. In most cases, the accidents were attributed to negligence or carelessness by the small vehicle driver. The limited visibility problem still exists, though, and a solution is needed. Initial Solution The usual plane mirror on the driver's side and the convex mirror on the right front of the haulage truck allow only limited rear visibility. The typical, right side convex mirror is generally small and difficult to locate at a glance. This convex mirror also presents an image that distorts distance perception. These mirrors are of¬ten broken and immediate replacement not demanded or made. The US Bureau of Mines, in a contract with M.B. Associates, San Ramon, CA, developed an improved visibility system. It consisted of a larger, left view mirror and unique, blind area viewer. The large 230 x 690 mm (9 x 27 in.) left mirror has a small convex spot mirror near the bottom. The entire unit can be quickly replaced if broken. The large size provides a full view of driver orientation features such as the rear tire and the top of the load bed. The right 300 x 410 mm (12 x 16 in.) mirror has a convex surface and is quite rugged. The 510 mm (20 in.) spherical radius presents the operator with some distance distortion, but objects in its view are easily seen. The "blind area viewer" consists of a modified fresnel lens that allows the driver to "look around the corner." Installation of three of these lenses on the front of each haulage truck is rec¬ommended for adequate blind area coverage. This system significantly increases an operator's field of view and allows viewing of objects within about 3 m (9.8 ft of the truck. Many open-pit mines are nor mounting on smaller vehicles a long whip with a flag and lamp or both. This increases vehicle visibility to haulage truck operators. The whip is permanently attached to the mine vehicle. It can also be magnetically attached to transient vehicles. The whip system. though, is inadequate for visibility in the critical rear and right front blind areas. Alternate Solutions All of these visibility aids as¬sume an attentive driver. In addi¬tion, areas such as the rear blinc, area are not covered. Based on the inadequacy of existing visibility systems, Anaconda made a com mitment to further the truck de¬tection technology. The best ap¬proach was considered to be ar active system. It would notify the haulage truck operator that an en¬croaching vehicle is present. Sev¬eral systems were considered, in¬cluding ultrasonics and elec¬tromagnetics. For the ultrasonic system, com mercial and in-house design were looked at. Designing an( building transducers with the spe cific beam shape to match the haulage truck blind spots re¬quired a major technological breakthrough. False alarms ap¬peared difficult to prevent en¬tirely. They were caused by pass¬ing, trailing, or leading vehicles a., well as nonthreatening objects. As a result of these problems, the ul¬trasonic technique was not pur sued. An alternative, an electro

Jan 7, 1982

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By E. DeLilia

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to in-crease productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: ? Prudent engineering. ? Proper planning. ? Realistic feasibility studies. ? Effective specification. ? Thorough training of the mine personnel.

Jan 1, 1995

By U. F. Beichmann

INTRODUCTION The City of Oslo together with the neighbor municipalities, Baerum and Asker, are presently building a jointly owned sewage treatment plant located on the west side of the inner Oslofjord. The project is scheduled for completion late 1981. Because the location of the treatment plant is at a distance of about 20 miles (30 km) from the city center, a discharge of more than 13 yds 3/sec (10 m3/sec.) of sewage and storm water will have to be transported over considerable distances. The topography of the area and the geological conditions early indicated that the only realistic transport method had to be through tunnels. As planning proceeded, full face tunnel boring emerged more and more as a favorable alternative to conventional drill and blast medhods. Today the scheme comprises nearly 25 miles (40 km) of tunnels being excavated by full face tunnel borers. In addition a number of access tunnels and cross cuts are to be excavated by conventional methods.

Jan 1, 1979

By Andrew H. Merritt

INTRODUCTION The prediction of the engineering behavior of a rock mass depends upon the systematic analyses of the results of an exploration program, and upon the recognition of the significant rock properties in the early stages of excavation. The variations in rock properties in different geologic terrains and the state of the geotechnical art preclude complete success in the former case, and we therefore must rely heavily on the experience gained in the latter phase. The geotechnical information obtained from these two phases is only of value to the design engineer when applied to the rock behavior during excavation and subsequent plant operation. Pertinent questions which must be answered include: how does the joint orientation and frequency effect tunnel support and overall cavern stability; how does the depth of surficial soil or weathering effect foundations or slope stability for portal cuts; are there permeable zones within the rock mass that could lead to leakage problems around penstocks and is the material in these zones soluble or likely to pipe in the long term; and does the proposed engineering structure fit the terrain, or will it inevitably lead to problems requiring extensive remedial treatment. During the early stages of construction there are two types of geotechnical information required; actual rock behavior with respect to the original design assumptions,

Jan 1, 1997

By S. K. Kawatra

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern U. S. and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effects of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that under otherwise constant operating conditions, the d50(c), size decreased linearly with increasing temperature, while the shape of the reduced efficiency curve remained constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1988

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By Betty L. Gibbs

Before the first shovelful of dirt is removed from a developing mining property, a wide range of data must be collected, organized and analyzed. Among the key steps in this process are: • Visualization of the deposit from drill hole data and geologic interpretation, using all available information, including surface geology, geochemistry and geophysics. • Drawing of vertical and horizontal sections. • Construction of a 3D solid model of the deposit. • Contouring of deposit outlines and geological structure until the model represents best estimate of reality. • Estimation of grade and quality distribution. • Calculation of reserves. • Examination of possible mining methods. • Determination of economic feasibility. Many techniques are available to aid in this process of mine project feasibility analysis, from quick pencil calculations to sophisticated computer methods. However, time races faster in the complex modem business world than it did 50 years ago. Tried and true pencil methods take too much time. Opportunity may pass a mine developer by while a property is still in the first stages of analysis. In the days of hand techniques, initial analysis of the economic feasibility of a mining project usually stopped with reserve calculations and broad mine planning. Further planning was not done or was done only for the short term. Manual techniques require too much time and manpower to evaluate a longterm mining program. Mining-industry recognition of computer utility has increased. Most companies now use computers in technical applications and could not conceive of working without them. Building initial computer models of a deposit may take nearly as long as hand techniques. But the payback comes when changes are needed and a variety of mine plans are quickly tested.

Jan 1, 1990

By Caelen D. Anderson

An investigation of a hydrometallurgical method for the recovery of tellurium dioxide from cadmium telluride (CdTe) thin-film manufacturing scrap was conducted. Sulfuric acid/ hydrogen peroxide lixiviation was employed to selectively leach cadmium and oxidize tellurium to tellurium dioxide (TeO2). Experimental variables included solution pH, pulp density, oxidant (H2O2) concentration, temperature, agitation rate and residence time. After one hour of lixiviation, no noticeable increase in grade or recovery occurred; thus, all experiments were performed for one hour. Leaching results showed it was possible to recover at least 74% of the tellurium, while producing a 98% pure TeO2 product. Additionally, an apparent activation energy value of 12.1 kJ/mole (2.9 kcal/mole) was determined. This value, along with results from agitation rate experiments, indicated the reaction was primarily controlled by diffusion through the product layer. During lixiviation, partial dissolution of tellurium proved inevitable. Thus, a second step: ammoniacal precipitation was introduced to recover the aqueous tellurium as a precipitate. A statistical experimental design (DOE) was used to identify the significant effects from the residual effects. Experimental variables included precipitation pH, temperature, initial tellurium tenor and agitation rate. Precipitation results showed that it was possible to produce a low-grade (46% Te) precipitate, while recovering 98% of the aqueous tellurium species. The precipitation pH and temperature (°C) were determined as the significant effects for both the grade and recovery of tellurium. Agitation rate and initial tellurium tenor were determined as the residual effects and did not influence the grade or recovery of tellurium. An illustration of tellurium recovery, as a function of the significant effects, is illustrated in Fig. 1.

May 1, 2012

By Wescomb R. Jones

The United States is the world's largest producer of hydrofluoric acid (HF), with its 1971 output of 317,000 short tons representing about 40 percent of the estimated Free World production. U. S. production has increased over five fold in the past 20 years, with a growth rate of about 7 percent per year between 1960 and 1970. However, the growth rate to 1977 is expected to be less than 5 percent per year, due primarily to a reduced rate of growth in requirements by the aluminum industry and an expected increase in imports from Canada and Mexico. This discussion will include our analyses of the consumption pattern for HF in 1972 and the factors influencing the demand forecast for 1977.

Jan 1, 1973

By Doandy Yonathan Wibisono

Shotcrete is a versatile and widely utilized rock support material in mining and civil engineering projects due to its adaptability, strength, and efficient application. It immediately stabilizes rock surfaces, effectively controlling loose materials and preventing rockfalls in underground excavations. This paper focuses on assessing and analyzing data from observations of nozzlemen (shotcrete sprayers) during primary ground support activities in an underground mine. The study highlights the importance of nozzlemen’s skills in ensuring the quality of shotcrete application, which is critical for underground mining operations’ structural integrity and safety. A comprehensive training program and field support were implemented to enhance the nozzlemen’s proficiency. The training set covered theoretical knowledge and practical techniques to improve shotcrete application daily. Proficiency improvement was assessed using quantitative metrics, with rebound percentages decreasing by 5–14% as nozzleman competency increased. The results of this initiative showed significant improvements in shotcrete quality, including increased efficiency, reduced waste, and fewer reworks or rehabilitations. The findings aim to contribute to a broader understanding of best practices in shotcrete application and nozzlemen training, ultimately enhancing ground support application measures in the mining industry.

Feb 1, 2025

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By Agus Sasmito, SRIVATSAN JAYARAMAN SRIDHARAN, Akash Adhikari, Purushotham Tukkaraja

The amount of toxic fumes produced during blasting operation depends on the types of explosives used, product formulation, degree of confinement, conditions of use, and reactivity of the explosives with the host rock. Ammonium nitrate and fuel oil (ANFO) is still the explosive of choice due to its lower price and ease of use/loading. If not properly monitored and controlled, toxic fumes produced from blasting operations can have serious health hazards [1]. This paper presents a novel technique developed to track trapped fumes during a development blasting.

Aug 1, 2022

By Stephen G. Tough, Ted M. Noskiewicz

INTRODUCTION For many years, in Europe and in North America, pre-formed metallic and concrete segmental linings in tunnels have been used extensively as temporary and permanent ground support systems. In the United Kingdom the use of cast iron as a means of ground support in mining shafts dates from the first decade of the 19th century. Although at that time wood tubbing was extensively employed, cast iron was used in shafts at Wallsend and Percy Main collieries in the North East of England. The original form of cast iron tubbing consisted of cylinders which were lowered bodily into the pit and were built from the bottom up, but subsequently they were subdivided into segments which involved the making of vertical as well as horizontal joints. Principally, the practice of providing immediate pre-formed support developed because of the incompetent state of the surrounding ground and, although this still remains the over-riding consideration nowadays, several other factors are examined before finally deciding what type of lining to use. Other branches of sub-terranean technology such as tunnel thrusting or immersed tubes (both of which involve pre-formed linings) can provide alternative solutions to problems hitherto thought better solved by bored tunnelling methods. However, this paper will confine itself to those linings developed for the more traditional tunnelling methods. Usually the shape of segmentally lined tunnels is circular because this profile is the most suitable for bad ground and many tunnelling machines. This does not always lead to the most economic use of space within the tunnel and horseshoe or elliptical linings are sometimes used in suitable ground. The number of segments

Jan 1, 1974

By John A. Organiscak

The Bureau of Mines evaluated a new dust control technique for longwall personnel required to work at the tailgate end of the face. This technique utilizes a water-powered scrubber to clean a portion of the face air, which is discharged behind a brattice partition at the working area. Laboratory simulation of this system in a wind tunnel resulted in average efficiencies greater than 70 pct with system efficiency directly related to scrubber quantity. Underground evaluations indicated a similar direct relationship between scrubber quantity and system efficiency. Gravimetric measurements of respirable dust made during these underground evaluations resulted in average protection efficiencies ranging from 30.7 to 42.5 pct with increasing scrubber air quantity.

Jan 1, 1983

By K. A. Smith, X. Cheng

Introduction The separation of minerals from complex sulfide ores by flotation requires careful control of the surface chemical behaviors of the minerals constituting the ores. When the minerals in the ore are finely disseminated, extremely fine grinding is needed to liberate the minerals. Fine grinding is not only an energy-intensive operation, but also influences the flotation behaviors of liberated minerals. Steel balls are commonly used for grinding. Galvanic interactions occur not only between sulfide minerals and grinding media but also among the different sulfide minerals themselves. The electrochemical characteristics of chalcopyrite and pyrrhotite when they are independently coupled with steel grinding media and the relevance of these characteristics to the flotation behavior of these minerals have been exten¬sively studied (Cheng and Iwasaki, 1992: Li and Iwasaki, 1992). These studies dealt with reactions in two electrode combinations, simulating mineral-grinding medium and mineral-mineral interactions. In practice, however, it is more common to involve more than one sulfide mineral. In a study of a pyrite-pyrrhotite-mild steel system, Pozzo et al. (1989) provided evidence that a mineral having an intermediate potential could behave differently, depending on the condi¬tion of galvanic contact. This investigation was undertaken to study a chalcopyrite-pyrrhotite-mild steel system to gain better in¬sight into the mechanism of multiple galvanic interactions. A three-electrode system was chosen to simulate a typical copper sulfide ore. The sulfide minerals were represented by chalcopyrite and pyrrhotite. The grinding medium was rep¬resented by mild steel. The nature of galvanic interactions involving these minerals and grinding medium in an oxygen atmosphere was investigated in a three-electrode combina¬tion, and an attempt was made to relate the laboratory flotation results of pyrrhotite-chalcopyrite ores. Possible implications to the differential flotation of complex sulfide ores are discussed. Key words: Electrochemistry, Flotation, Sulfide ores Experimental The pyrrhotite (57.74% Fe, 0.09% Cu, 4.84% Ni and 36.54% S) sample was obtained from Falconbridge Ltd.'s Strathcona mine, Ontario, Canada, and the chalcopyrite (26.00% Cu, 28.57% Fe, 0.05% Ni and 31.52% S) sample came from Transvaal, South Africa. Mild steel (AISI 1020, 0.2% C) was chosen to represent grinding media. A conventional three-electrode cell was used in the elec¬trochemical measurements. The working, counter and refer¬ence electrodes were, respectively, sulfide minerals or mild steel, graphite rod and saturated calomel electrode (SCE, 0.245 V vs. standard hydrogen electrode). The exposed areas of the sulfide minerals and grinding medium electrodes were approximately the same (0.17 to 0.19 cm2). The preparation methods of working electrodes, the reagents used, the experi¬mental procedures and the instrumentation were the same as those described previously (Cheng and Iwasaki, 1992). Rest potentials of pyrrhotite, chalcopyrite and mild steel were measured individually in 0.05-M sodium sulfate solu¬tions. Combination potentials and galvanic currents of the sulfide minerals and grinding medium were measured in short-circuited two- and three-electrode systems. All poten¬tials in this study are quoted in volts with respect to the standard hydrogen electrode (SHE). To simulate the constantly abrading conditions in a ball mill, rest potentials, combination potentials and galvanic currents were also measured by rotating a porcelain ball against chalcopyrite, pyrrhotite and mild steel electrodes in

Jan 1, 2000

By R. L. Grayson, L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams.

Jan 1, 1995

By Ch. R. V. S. Nagesh, Ramesh Naidu Mandapati, Venkata Swamy Nalajala, Tondepu Subbaiah, Naga Jyothi Kothamasu

Leaching studies of magnesite obtained from Tamilnadu Magnesite Limited, Salem, have been carried out using hydrochloric acid leaching and percentage of magnesium chloride recovered was estimated. The variables considered in this study were the following: duration of leaching, volume percentage of hydrochloric acid, temperature, and pulp density. Percentage recovery of magnesium chloride increased with duration of the leaching, volume % of concentrated hydrochloric acid, and temperature. Percentage recovery of magnesium chloride decreased with increase of pulp density. The optimum conditions found to be pulp density (10%), hydrochloric acid concentration (30%), duration of leaching (2 h), and temperature (348.15 K). Iron was removed by treating the leach liquor with hydrogen peroxide and by raising the pH to 3.5–4. The purified leach liquor was subjected to spray drying for producing high pure magnesium chloride.

Jun 7, 2022

By H. I. Morrison, A. J. deVilliers, D. T. Wigle, H. Stocker

INTRODUCTION At the end of 1959, high levels of radioactivity attributed to radon and its daughter products were discovered in the fluorspar mines at St. Lawrence, Newfoundland. These levels were presumed to be the cause of an unusually high incidence of lung cancer among the fluorspar miners (deVilliers & Windish, 1964) (Parsons et al. 1964). The mining of fluorspar (calcium fluoride) began in 1933 as open pit operations but converted to standard underground mining procedures in 1936. During the second world war, production was greatly expanded as a result of increased demand for fluorspar used in the production of steel. Wet drilling was first introduced into general use in 1942. Ventilation was mainly by natural draft occasionally supplemented by small blowers. The amount of ventilation varied greatly between mines as well as over time. For example, one large mine, the Iron Springs mine, had only a single small raise to the surface some 600' from the central shaft. Other mines, such as the Director mine, had a number of raises to the surface and, as a result, had far better ventilation. Mines also varied by the amount of ground-water which seeped into them. In the early 1950's, an unusually large number of lung cancer cases were diagnosed among the fluorspar miners. As a result, in 1956 and 1957, J.P. Windish of Canada's Department of Health and Welfare tested for possible causative agents in the mines. Unfortunately, radon measurements were not conducted until 1959 and 1960 when Windish tested Director mine as did the A.D. Little company in 1960. As a result of the high radon levels found, mechanical ventilation was introduced and the concentration of radon dauthers fell, on the average to well below 1 WL. During this period, lung cancer cases continued to be diagnosed with 29 lung cancer deaths recorded by 1964 and 71 by 1971. As of July 1981, 105 lung cancer cases had been identified (Hollywood, 1981). Previous reports concerning the fluorspar miners have dealt in detail with the factors in the occupational environment and discussed occupational mortality patterns. The purpose of this paper is to review further the mortality experience with particular reference to lung cancer in relation to cumulated radiation exposure and to describe briefly our ongoing study of this group. METHODS Occupational histories were prepared for men who had been employed by the mining companies at St. Lawrence during the period 1933 to 1977. The histories were compiled from company records except for the period 1933 to 1936, records for which were lost in a fire; however, the occupational histories for this period were completed by searching census records and interviewing company officials, ex-employees and others. In addition, occupational and smoking histories were also obtained for some miners during a survey conducted in 1978. Occupational records included name and date of birth as well as the type, place and hours of work by year. For each year prior to 1960, hours of work were converted to working months (1 WM = 167 hours) and were multiplied by the estimated average radon daughter concentration in working levels (WL) to yield the annual radiation exposure in working level months (WLM). Pre-1960 radiation levels were estimated on the basis of the history of mining methods employed, ventilation history of the mine, type and place of work and conditions under which the first radiation measurements were made in 1959 and 1960 (deVilliers and Windish, 1964). During the period from 1960 to 1967, the average exposure was about 0.5 WL. Beginning in 1968, radiation levels were measured more frequently, and, beginning in 1969, daily exposures for each worker were recorded based on radiation levels in the place worked on a given day. Mortality data were obtained from medical certificates of death. In a small number of cases, medically certified death certificates were unavailable. In these cases, probable cause of death were obtained from forms completed by the local clergyman (returns of death), parish records, information obtained from interviews with family members of the deceased and/or hospital information, before assigning a cause of death. Data obtained from these sources were found in Tables 1, 2 and 4, cover the time period 1933 to 1971. Data in Table 3 as well as in Figures 1 through 3 cover deaths from 1933 to 1977, and includes only those miners for whom medical certificates of death were available. Two medically certified causes of death were changed from other causes to lung cancer on the basis of pathology reports.

Jan 1, 1981