Search Documents

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By Xiaolong Bi, Shaohua Luo, Longjiao Chang, Shiyuan Cao, Jianan Liu

The abstract discusses the extraction of silica from nickel laterite ore using a hydrothermal process with sodium hydroxide. The effects of reaction temperature, time, and NaOH-to-ore ratio on silica extraction were investigated. The optimal conditions were determined, achieving over 98% silica extraction. The mechanism involves the reaction of Si in lizardite and quartz with sodium hydroxide, forming sodium silicate solution. Other metals like Mg, Fe, and Ni are enriched in the residue.

Apr 21, 2022

By E. A. Devuyst

Metallurgical processes involving the use of cyanide such as gold cyanidation, metal plating and flotation, generate effluents containing cyanide and cyanide in complex combinations with heavy metals in quantities exceeding those regarded as being safe for discharge into streams. A new process for destruction of free and complexed cyanide and related-species in wastewaters has been developed at the Inco research laboratories using sulfur dioxide, air and lime. High reaction rates are obtained in the presence of a small amount of copper which acts as a catalyst. Cyanide species can be reduced to as low as 0.1 mg/L in a very short treatment time. Examples of treatment of gold mill effluents and barren slurries, plating rinse waters and flotation liquors or tailing slurries are given.

Jan 1, 1982

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By G. H. Lewis

This work was completed in a 440 KW pilot-scale combustor in preparation for a 50,000 Kg/hr industrial steam boiler limestone injection test program. The main objectives of the work were to: (1) identify the variables which affect sulfur capture, (2) determine the maximum sulfur removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. The variables which were identified as being important in sulfur capture were: Ca/S molar ratio, flue gas temperature at the limestone injection location, and limestone particle residence time. The maximum sulfur dioxide removal was 72%. The addition of limestone increased the particle deposition rate in the combustor; however, all deposits were easily removed by an air lance.

Jan 1, 1985

By D. Shuck

Incorporation of a 2,727 mtpd, $5.7 million flotation circuit into the Mclaughlin flowsheet was completed in November 1991. This capital addition reduced overall operating costs and improved the gold recovery of the low grade refractory reserves over that expected for direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate which is utilized to supplement feed to the pressure oxidation circuit.

Jan 1, 1994

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By Peter Dietrich, Joseph DeMello, Norbert Fuegenschuh, Kerwin Hirro, Jeff Brandt, Mike Cole

This paper presents a successful case history of the ground improvement efforts and excavation of twenty-three cross passages between twin bore tunnels driven by EPB tunneling machines in Los Angeles, California on Section 1 of the Westside Subway Extension. Unique and complicated ground conditions local to the tunnel alignment include San Pedro sands, siltstone/claystone Fernando Formation, and zones of “asphalt impacted soils.” To provide water cut-off and soil stabilization, jet grouting was performed prior to TBM excavation at the location of many of the cross passages. However, upon investigating the cross passages prior to excavation, the subsurface conditions required additional measures and SEM tools to ensure successful completion of the project.

Jun 13, 2023

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

Process plant modeling in the computer environment has been developed over the past 40 years by implementing the comminution models formed by the Julius Kruttschnitt Mineral Research Centre, University of Queensland, in the early 1970s. The models for the other processes in a mine value chain, such as blast fragmentation and flotation, were continuously developed and improved in parallel as well. Other research and commercial entities have also developed process modeling methodologies in the computer environment, which evolved as specialized commercial software or through equations set up in Excel spreadsheets. These were performed on a local computer, in thousands of simulations over a long period of time due to hardware limitations and the lack of a fully automated process. This limits the application of detailed process simulations for scale-up and strategic planning analysis, as they require many simulations to cover all possible scenarios which would take a lifetime when using local computers. The Integrated Extraction Simulator (IES), as the next generation of cloud-based software package, has made it possible to run simulations on the entire operation value chain in the same platform, including drilling and blasting, crushing, grinding, flotation, and other downstream process and material-handling units. This capability has allowed IES to handle multivariable simulations across the mine value chain, including pre-concentration and in-pit size reduction, and modify the process simultaneously.

By D. L. Schenk

The Navajo Mine is exclusively a multiple-seam surface coal mine located in the northwest comer of New Mexico. The property is situated entirely on the Navajo Indian Reservation. It is owned and operated by the Broken Hill Propriety Co. Ltd., of Melbourne, Australia. The mine began production in January 1963 with a long-term fuel supply agreement with the Four Corners power plant. The 2175 MW nominal generating capacity of the Four Corners powerplant consumes 7.2 Mt to 7.7 Mt/a (8 million to 8.5 million stpy) of coal. The Navajo Mine has estimated reserves totaling 1 Gt (1. I billion st) of strip minable coal. Only about one-third of that total is presently committed to the generating station. As development continued over the years, mining operations advanced into more complex geologic areas to satisfy the utility's demand for coal. To optimize the committed reserve and provide competitively priced coal to the customer, the Navajo Mine began developing a new pit in June 1986. The Dixon Pit boxcut development was completed in April 1987. About 6 hm3 (7.9 million cu yd) were stripped, uncovering 929 kt (1 million st) of coal. Strip ratio was 7.74:1 including 36.8% rehandle of prime yardage. This case study of the fourth production cut highlights a variety of dragline stripping techniques including highwall bench (overburden) side cast, intermediate highwall bench (parting-interburden) side cast and spoilside bench (partings-interburden) stripping methods. The Dixon Pit offers considerable challenges in the surface recovery of up to seven seams of coal within the 1432 m (4700 ft) of total pit length.

Jan 1, 1990

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By Robert Cook, Valeria Zarate, Jason Hallowell

The long hole open stoping (LHOS) method is widely used in underground mining. While methods to predict stable stope geometries are well established, the ability to maintain a stable back often assumes effective ground support across the full stope span. The efficacy of the support strategy is dependent on rock jointing, quality, density, top cut width and height, and the type, amount, and orientations of bolts installed. However, it is becoming increasingly common for operators to assume narrow top cuts in service of wider stope spans with minimal bolting coverage. Failure to account for the required top cut drift size and support requirements can ultimately lead to raveling type instabilities along stope shoulders that result in back collapse. A new method has been developed to evaluate the minimum top cut dimension necessary to accommodate wider stope spans with various rock bolting configurations. Due to the economic impacts of top cut development and support, this is a critical consideration in the accurate costing and scheduling of a LHOS operation. Tables 1 lists the acronyms are used throughout this paper.

Feb 1, 2025

By E. B. Kroeger, Y. P. Chugh

The goal of this project is to develop, demonstrate, and document the beneficial use applications of a ponded F-fly ash as a road subbase material for the 2.1-mile Meredosia Industry Access Truck Route in Meredosia, Illinois. Approximately 60,000 to 70,000 cubic yards of ponded fly ash are proposed for use on this project without negative environmental impacts to surface water or groundwater. The County Highway Truck Route will consist of a 24-foot wide road built on a 0 to 7-foot thick compacted F-fly ash subbase. Laboratory testing indicates this fly ash will serve adequately as a road subbase, conforming to IDOT standard specifications. The economic considerations of using the Meredosia F-fly ash will also be developed so that a detailed cost-benefit analysis can be prepared for this project and for future projects. This project represents a two-year cooperative development and demonstration effort among the Office of Coal Development and Marketing (OCDM) of the Illinois Department of Commerce and Community Affairs (IDCCA), Southern Illinois University (SIU), Morgan County Highway Department (MCHD), Illinois Department of Transportation (IDOT), AmerenCIPS, and the Morgan County Regional Planning Commission. It is anticipated that monitoring activities will continue for a period of three (3) years after the completion of this project. The MCHD and IDOT will oversee all construction activities and long-term performance evaluation studies. Successful demonstration of large-volume beneficial use applications of F-fly ash at this site will significantly reduce management costs for power plants burning Illinois Coal. Furthermore, it will encourage similar utilization strategies at other sites in the State of Illinois.

Jan 1, 2002

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026

By Collin L. Stewart

Published subsidence data for the western United States is limited in comparison with data for the east. This paper summarizes the results of a subsidence monitoring program above two longwall panels at the Foidel Creek Mine located in northwest Colorado. The monitoring area is characterized by overburden ranging from 1000 ft to 1100 ft in thickness. The surface slope parallels the dip of the bedding at approximately 5 deg. Average mining height is 9 ft. Smax averaged 3.4 ft. Draw angles averaged 15 deg for up-dip ribsides and 19 deg for down-dip ribsides. A site-specific profile function is developed from the data.

Jan 1, 1986

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984

By Jennifer King, Julius Strid, Steve Brandon

The Upper Hidden Basin Diversion (UHBD) tunnel was driven approximately 1.2 miles by the drill-and-blast method primarily through massive granite bedrock geology for the Kodiak Electric Association, Inc. (KEA) in Kodiak, Alaska. The tunnel was driven from both portals with a constant 11-ft straight-leg horseshoe cross-section. The design and construction of the tunnel was driven by logistics and weather conditions due to its remote location and the rugged terrain of the project setting. This paper will discuss the successful completion of a challenging project over a ve-year period from preliminary planning through the design and construction phases.

Jun 23, 2024

By Bernard A. Grand, Gary A. Almeraris

This project involves the reconstruction of a 1,100 ft. long by 75 ft. wide segment of an existing 4 to 5 track subway under Northern Boulevard in the Borough of Queens in New York City. The project includes widening the existing subway to permit the construction of new inbound and outbound subway (T1 and T2) ramps adjacent to and under existing operating tracks. The plan of the project is shown in Fig. 1. Existing tall buildings along the job site and a contaminated groundwater plume under an adjacent rail yard required construction of slurry concrete walls along the east and west construction limits. Groundwater cutoff across the north and south construction limits of the subway was achieved by jet grout walls built across the subway invert slab between existing track and third rails. The work involved dewatering the construction site to a depth of about 50 ft. below street grade. This is a four year project and includes extensive work to maintain and protect subway and vehicular traffic of over half a million commuters a day through the work area. The project cost was $160,000,000.

Jan 1, 1999

Energold Drilling Corp. is a leading specialty drilling company servicing the mineral and energy sectors in the Americas, Africa and Asia. Energold specializes in mineral exploration in remote locations with limited infrastructure. Such locations require the smallest footprint possible going in, leaving as little or no evidence on their way out. Energold?s rigs can be transported by helicopter or manually on footpaths as narrow as 1 m (3.3 ft). They set up quickly and then are struck and packed out, with any sign of their presence quickly disappearing behind them. Energold has teamed up with Atlas Copco and its team of engineers in North Bay, Ontario to design small rigs capable of drilling to a variety of depths, as required for each project.

Jan 1, 2013