Search Documents

By Utku Gumus, Ertan Bostanci, Hanifi Copur, Ahmet Rüfai Bilgin, Ugur Altay

"Field observations on replacements of 12-inch constant cross-section double disc cutters in Tuzla Wastewater Tunnel excavated by an EPB TBM with 3.151 mm excavation diameter excavating hard rock are summarized. Cutter life is correlated to rock’s uniaxial compressive strength and Cerchar abrasivity index, and TBM operational parameters. Number of cutter replacements, average cutter replacement rates and types of cutter damages are summarized. The relationships between cutter life and rock properties and TBM operational parameters are analyzed by single variable regression method. Detailed analysis between chainages 1+200 and 1+982 km indicates that average cutter consumption rate is 35.7 m3/replacement (4.6 m/replacement). Cerchar abrasivity index and uniaxial compressive strength does not indicate any meaningful relationship with cutter life. Penetration per revolution and field specific energy might be used for predicting lives of constant cross-section double disc cutters. However, additional data is required to generalize the findings of this study. INTRODUCTION Cutter life / replacement and/or consumption rates in terms of cutter cost and replacement time loses is one of the most important parameters affecting excavation performance of mechanical excavators, especially of TBMs used very widely and equipped with usually disc cutters. Predicting cutter cost is a very important task in especially feasibility stage of tunneling projects. Basic parameters affecting cutter life can be classified into 3 general groups as geological and geotechnical, excavation machine (TBM) related, and operational parameters (Bilgin et al., 2013). The geological and geotechnical parameters are the most dominant ones among them. The machine related parameters should be arranged in accordance with the expected geological and geotechnical conditions for the best TBM excavation performance and minimum cost."

Jan 1, 2016

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By Donald Bishko

Zoning is the legal means by which land use can be controlled. Although zoning laws have historically been quick to prevent quarrying, one is hard pressed to find zoning ordinances which specifically state that land should be used (or held in reserve) for quarrying and prevent other uses such as recreation, housing, etc. This situation is especially true when the mineral to be quarried has a low intrinsic value such as sand, gravel, and crushed stone. The chance of a gold mine surviving urban sprawl is probably considerably greater than that of a sand and gravel pit, even though it is possible that the dollar value of the sand and gravel' would exceed that of the gold mine. The research reported herein was concerned with two major topics: to delineate the real costs associated with the non-protection of our construction aggregate resources (growth minerals) and to develop a computer simulation model which would aid planners in making economically sound decisions. This paper describes the problems faced by the mineral aggregate industry and discusses the role of computer simulation in planning problems. It briefly describes a simulation model which has been developed and previously reported12 and discusses the results of a pilot study conducted on the Tri-City area (Albany, Schenectady, and Troy, New York). 3

Jan 1, 1970

By J. S. Walstrom

Debate on an appropriate, acceptable method of regulating mine and mineral processing wastes has been ongoing since Congress passed the Resource Conservation and Recovery Act (RCRA) on October 21. 1976. Final regulatory determination on which mineral processing wastes are excluded from the RCRA hazardous waste regulations under the Bevill amendment was made by the U.S. Environmental Protection Agency on June 13, 1991. Regardless of whether a mining or mineral processing facility?s waste stream(s) lost or maintained its exclusion status under the Bevill amendment, that facility can expect more stringent regulation of affected waste streams. These more stringent regulations will be added to an already complex regulatory maze, which includes the Clean Air Act (CAA), Clean Water Act (CWA), Safe Drinking Water Act (SDWA), Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), Superfund Amendments and Reauthorization Act (SARA), and Toxic Substances Control Act (TSCA), as well as state and municipal environmental regulations.

Jan 1, 1992

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By Ma Fangyuan, Li Min, Xu Bing, Xian Yushuai, Zhao Tonglin

The study explored a new combination amine collector (XK-28) that can obtain better flotation index and defoaming rate for magnetic iron ore. A pure quartz mineral test indicates that dodecylamine, XK-I, or XK-II has good collection effect on quartz and their best flotation pH is in the range of 6–7. The experimental results of a combination collector (XK-I:XK-II = 2:8.) show that the separation effect for quartz and magnetite is better than that of a single collector. The single factor for actual mineral test shows that when the combined reagent is used as the collector, the best conditions are pH = 7, 90 g/t dosage, and XK-I:XK-II = 2:8, which is consistant with the pure mineral test. The difference for dodecylamine as a collector is that the optimal dodecylamine dosage is 60 g/t. Under the best conditions of actual ore test, dodecylamine and XK-28 are respectively used as the collector to compare the flotation indexes. Study results indicate the magnetite grade using XK-28 as the collector is higher by 3.02% than that of using dodecylamine, recovery is increased by 1.92% over that of using dodecylamine. Based on the measurement results of zeta potential, uses of XK-28 can slightly increase the zeta potential difference of quartz and magnetite to enhance the flotation effect. The mechanism of action between the XK-28 collector and the actual ore from the Gongchangling plant is physical adsorption, and this adsorption also has hydrogen bond formation. Contact angle results shows that XK-28 improves the hydrophobicity of quartz better than dodecylamine. Compared with dodecylamine, XK-28 is more sparsely arranged on the surface of the foam. The foam produced by the XK-28 collector has better air permeability and it is more likely to merge and disappear with bubbles.

Jul 21, 2021

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By D. Malhotra

Metallurgists are continuously striving to improve recovery. But optimization of profits and/or revenue dictates that recovery can be sacrificed at the expense of throughput. However, recently there has been significant interest in the concept of retreatment of tailings to enhance recovery and hence revenue while maintaining high throughput. The authors discuss the technical and economic factors that need to be considered in evaluation of the feasibility of retreatment of tailings including the potential feed streams (i.e., rougher tailings, cleaner tailings, etc.) and processing options (i.e., physical beneficiation, chemical processing, etc.). A case study for base metals is discussed.

Jan 1, 1994

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By James Wm. White

Calculation of consistent steady-state mass balances in operating metallurgical plants and pilot plants is of interest for many reasons. In general, enough data can - and should - be collected to overdefine the system, i.e., permit calculation of nonmeasured quantities via more than one path. In such cases, resulting steady-state metallurgical mass balances rarely close due to sampling, analysis and/ or instrument error. Indeed, determination of a valid calculational sequence for complicated process flowsheets with multiple recycle streams can prove quite difficult. Here we present and discuss a method that has proven useful in analysis of numerous grinding circuit flowsheets of varying-degrees of complexity our technique requires only a consistent process flowsheet with appropriate associated data and arbitrary numbering of streams and equipments. Process topology and user data are decoded to yield a set of "search" or base variables and a set of "calculated" variables in solids, water, particle size and splitter parameter space. This procedure greatly speeds subsequent actual mass balance adjustment calculations since perturing certain variables (e.g., a solids value) does not require recalculation of other variables (e.g., the water balance). Finally, internal search and calculated variables are back converted to User units and used in a Sum-of-Squares criterion. Global minimization of this performance functional then yields a consistent mass balance in a least, squares sense. Weighting factors of choice can be used. Examples illustrate application of these methods.

Jan 1, 1979

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By Don S. McCoy, W. Joseoph Schlitt, Donald B. Swanson

Introduction Contract miners have long played an important role in the minerals industry. Historically, these were individuals who worked as underground miners and were paid by the ton or the day. These hardy types still ply their trade in the industry. However, today the term "contract miner" generally refers to an independent contractor who supplies the people and equipment needed to conduct surface mining operations for an owner or lease holder. At one time or another, contract miners have probably handled virtually every mineral commodity from sand, gravel, and stone quarrying to mining uranium and precious metal ores. In today's market, though, contract mining appears to be concentrated in just a few areas. These include precious metal mines, various types of solid fuel operations, and reclamation of abandoned mines. This article covers market areas, contract mining organizations and services, and their advantages and disadvantages. Gold and silver mines Although exact figures are not available, contract mining represents a significant element in the precious metals segment of US mining. For gold and silver, the growth in contract mining appears to be paralleling the overall growth in mining activity itself. Nevada is the largest gold producer in the US. The latest available data (1985) on open pit gold/ silver mines is summarized in Table 1 (Nevada Division of Mine Inspection, 1986). These figures show that contractors mined nearly half of the ore in 1985. Total tonnage mined, of course, was much higher for both owners and contractors. Assuming an average stripping ratio of 2.5 to 1, the total daily mining rate for the contractors was more than 145 kt (160,000 st). This translates into a contract mining rate of about 36 Mt/a (40 million stpy) based on 250 operating days a year. This approximate 50-50 split between owner and contractor also appears to hold for the future. Metals Economics Group (1987) published a survey of 51 short-range and 54 long-range precious metal projects being considered throughout the US. Contacts with owners, requests for proposals, and past corporate philosophies all suggest that about 55% of the open pit operations scheduled for the near-term will be contract mined. This represents an estimated 26 kt/d (28.5 stpd) of ore. A similar assessment of the long-term projects indicates that about 12 kt/d (13,000 stpd), or just under 50% of the open pit tonnage will be contract mined. There are several reasons why gold and silver represent such an attractive opportunity for contract miners. One is that many properties are owned or leased by individuals or partnerships that are essentially entrepreneurial. Many of these owners or lease holders have minimal mining experience. They must therefore either rely on contract mining organizations, sell an interest in the project to another mining company that will become the operator, or hire an experienced management team. For about the same reason, junior mining companies also represent good prospects for contracting. This is because most junior companies focus on exploration. They would prefer to spend their generally limited funds on drilling programs. Thus, they tend to minimize additional capital requirements by using contract miners or farming out the property to another mining company. Another good reason for using contract miners is the size of the deposit. Many properties are so small that their reserves will not support the capital expenditures

Jan 12, 1987

By M. R. Moon

The mine fire at Wilberg Mine in 1984 reached the surface resulting in the failure of the vertical ledge forming the roof and entrance for three main intake portals. The fallen material was covered with a concrete cap to seal the air from the mine. As the mine was recovered and ventilation pressure was placed on seals on the perimeter of the fire area, the concrete capped rubble proved ineffective. Due to the steep and rugged terrain and the inaccessibility to the portals from underground, horizontal holes were drilled into the portal entries and three seals were placed remotely. The seals in conjunction with pressure balancing the seals around the perimeter of the fire area resulted -in the control of the mine fire.

Jan 1, 1993

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By Stephen Njoloma, Ivan Hee, Ravi Jain, Mina Shinouda

"INTRODUCTION DC Water’s First Street Tunnel (FST) is comprised of a collaborative effort between DC Water, DC Water’s Project Consultants Organization (PCO) led by Greeley & Hansen and McMillen Jacobs Associates and the design-build team of Skanska, Jay Dee, and Parsons Brinckerhoff. The fast-track project includes elements that were designed by the PCO and released for construction by DC Water prior to Notice to Proceed (NTP) and elements designed by the Design-Builder from 30% to released for construction after NTP. This required effective communication and technical coordination for integrated engineering and efficient construction. The project, constructed in an urban residential neighborhood, included innovative construction methods such as multiple location ground freezing, utilizing a centralized freeze plant, to minimize community impact. The means and methods chosen for cast-in-place shaft linings, precast segmental tunnel lining, microtunneling, sequential excavation method (SEM) adits and near surface elements reflected the immediate and sensitive surroundings, which varied by construction staging area (CSA). Technical aspects of the project, relative to the evolution from pre-bid to construction documents, are discussed along with modified designs to suit means and methods. SCOPE OF WORK In 2012, four major storm events swept through the District of Columbia and hit the Northeast Boundary sewer shed particularly hard with the neighborhood experiencing severe flooding. The extreme nature of the flooding, the damage to private property, and the health risks associated with exposure to sewage led to a multi-agency response and community calls for answers and action. The Mayor assembled a Task Force to evaluate a range of potential actions to address combined sewer flooding including engineering, regulatory, code revision, and management improvements. The Northeast Boundary Neighborhood Protection Project was the outcome of the Mayor’s Task Force; it is a three-step infrastructure initiative designed to offload the undersized sections of the existing collection system that serves the Northeast Boundary drainage area by implementing the McMillan Stormwater Storage Project, First Street Tunnel Project and the future Northeast Boundary Tunnel Project. Until the Northeast Boundary Tunnel Project is completed, the First Street Tunnel Project will add 8 million gallons of combined temporary sewer storage in a new tunnel under First Street NW to relieve undersized sewers that traverse the Bloomingdale neighborhood."

Jan 1, 2016

By C. J. Greet

Grinding with an electrochemically inert grinding media (i.e., high chrome white iron) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption, and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that not only demonstrates the changes in the pulp chemistry, but also provide an indication of the magnitude of the metallurgical improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at several porphyry copper operations around the world: Newmont’s Cadia and Red Chris Operations, as well as Evolution Mining’s Northparkes Operation. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper and gold recoveries. However, many of the porphyry copper mines on the Eastern Pacific are copper-molybdenum deposits. The paper presents laboratory test results for typical copper-molybdenum operations and extrapolate these numbers to what might be expected should a plant trial occur.

Feb 1, 2025

By J. Larsson

In the pursuit of increased safety the mining industry has worked to develop systems for remote control and autonomous operation of both stationary and mobile equipment. This paper reports on a newly developed system for teleoperation and autonomous tramming of LHD (Load-Haul-Dump) mining vehicles that not only increases the safety of the operators, but also has the potential to increase productivity.

Jan 1, 2010

By M. M. Foss

Geophysical methods are gaining acceptance in the evaluation of coal mine ground control condition. The use of in-seam seismic investigations has contributed significantly to the body of information concerning ground control feature identification and analysis. Seismic methods have been used successfully in locating voids, faults, fracture zones, roof and floor rock interfaces, and more recently in characterizing in-seam stress distribution. Seismic tomography is an effective tool in data interpretation for several of these applications, but as is the case with other engineering application of geophysical techniques, there are limits as to how much substantive information can be interpreted from a given data set. This paper discusses some of the applications of in-seam seismic geophysical tomography, and the limits to which the transformation from raw data to information should be taken.

Jan 1, 1995