Search Documents

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Xun Luo, Yi Duan

A field trial of by distributed optical fiber sensing (DOFS) technique was conducted at a longwall coal mine in Australia. This investigation was designed to assess the applicability of DOFS for microseismic monitoring in mining. The experiments used commercially available optic fiber cables, geophones and associated data acquisition instruments – a fiber interrogator and a seismic recorder. The fiber cable was deployed in a 300m deep hole and in trenches of approximately 3.5 km long on the ground surface around and across the longwall panel being mined. The results obtained from the experiments have shown that DOFS is able to acquire microseismic data with quality that is comparable to geophones. It has been proven that DOFS can achieve higher spatial resolution for seismicity sensing and higher accuracy for locating events than a geophone network. These characteristics are particularly useful for using DOFS to monitor ground vibrations associated with ground caving processes and rock fracturing events induced by mining and civil engineering. It was also found that far more additional seismic events were recorded by the fibers than by the geophones. Automated data discrimination and processing methods must be developed in order to utilize DOFS for real-time applications.

Apr 26, 2022

By J. D. Vincent

The Henderson mine site is located at Red Mountain on the eastern slope of the Rocky Mountains, approximately 50 miles west of Denver, Colorado. The mill site is on the west slope of the Rockies and mine and mill will be connected by an underground railroad. All designs were for a 30,000 ton per day molybdenite processing plant with provisions for future expansion up to 50,000 ton per day if required. This plan did not just happen, but slowly evolved over the course of about three and one-half years. Many plants cannot afford such a delay, but the Henderson project will take about 10 years from the time it was first discovered until production starts, and these 3 !1 years were well spent in determining the best possible plant site and flowsheet. This paper describes some of the problems and the decisions made in arriving at the final location and flowsheet. The paper does not go into the specific details of how protection of the environment went hand-in-hand with all other project considerations. This particular aspect of the planning has been well-reported on other occasions and considerable information on it is readily available.

Jan 1, 1972

By A. Festa

Secondary crushing often gets good press for its increases in energy efficiency and SAG milling rates but for a project considering this option the proposed benefits soon get overshadowed by implementation concerns. Reverse engineering from the published case studies is risky unless the reader understands the drivers impacting stability and operability of the circuit. This paper discusses the features of secondary crushing for Greenfield and Brownfield SAG mill grinding circuits. It is the author?s view that secondary crushing rarely adds value to a Greenfield project and restricts future expansion. Its application is best retro fitted to Brownfield operations where the benefit gained for capital expended is excellent. Two case studies are presented to reaffirm these statements. The first case study shows that the implementation of partial and total secondary crushing increases SAG mill power efficiency and it offers substantial incremental increases in milling throughput with staged capital investments for the crushing and grinding circuits respectively. The paper provides a critical analysis of process conditions for secondary-crushed grinding circuits, with particular emphasis on Brownfield circuit retrofits. Furthermore, the second case study quantifies the economic impact of secondary crushing on circuit design for plant start up and it illustrates the limit imposed on plant expansion.

Feb 23, 2014

By L. B. Phelps

This paper focuses on the use of an integrated mine planing software package entitled "REMINE" which was constructed to provide a project evaluation tool for analysis of remining projects. Coal remining constitutes the affecting of sites which have had a past history of mining and have a pre-existing pollutional discharge. Such sites require a Best Professional Judgement (BPJ) analysis. The program was written to provide such an analysis with flexibility in the mine plans which can be analyzed. The process required for a BPJ analysis will be detailed and mine plan simulation performed to demonstrate the analysis.

Jan 1, 1990

By E. Oraby, S. Garcia, A. Thurgood, D. Bertoldi, G. O’Malley

Mining and Process Solutions (MPS) most advanced process, GlyCatTM is the only process that can be easily adapted to existing cyanidation plants in the market today whose real advantages over cyanidation are when treating copper containing ores, concentrates or tailings. With such complex material, GlyCatTM requires 70-90% less cyanide addition to achieve the same precious metal extraction. However, GlyCatTM is not simply cyanidation with added glycine. It is a completely different process where the solution chemistry and conditions needed to effectively leach the precious metals are quite different. Downstream however, the process is largely unchanged as the recovery of the leached gold and silver uses existing known processes such as conventional activated carbon or zinc cementation (Merrill-Crowe process). Another advantage is lower SCN, OCN, WAD and no free cyanide in the effluent which can substantially reduce cyanide detoxification requirements and decrease the OHS and ESG risk of the operation. This paper outline some of these differences and presents testwork, piloting and process examples to highlight the advantageous of this new process over conventional cyanidation.

Feb 1, 2023

By Peter F. Howard

The lower Middle Cambrian phosphorite deposits of the Georgina Basin shown in Figure 1 were found in the period 1966-1968 by three companies, namely, International Minerals and Chemical Corporation, Continental Oil Corporation and Broken Hill South Limited. Of these deposits the significant ones are Duchess, Sherrin Creek, D Tree, Lady Annie, Lady Jane, and Wonarah which together aggregate several billion tons reserves of phosphate. Due to the economic factors of freight costs to the coast and softening of the world market price for rock phosphate, none of them is in production, nor is any in the development stage. This paper reviews the historical background to the discovery of these deposits and then deals principally with the discovery of non-outcropping phosphorites in the Barkly Tablelands of Northern Territory by the interpretation of gamma radiation logs of abandoned water bores.

Jan 1, 1971

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By W. G. Pariseau

Joints may be taken into account when using numerical modeling as an aid to mine design by embedding joints in the model. When using the popular finite element method, say UT3PC, a pre-analysis step is necessary, Step 0. This step is for the computation of equivalent properties of a representative elementary volume of jointed rock (REV) in the model. This Step 0 is taken before Steps 1, 2 and 3 for specification of a rock properties file, generation of the mesh, and model analysis are taken. A brief explanation of equivalent properties and several examples aid in explaining the details of Step 0. Focus is on procedures, input files, and output to show ease of computation. Theoretical details are relegated to references (e.g. Pariseau 2022). Comparisons of safety factor distributions about example mine excavations with direct scaling from mine observations then offer some insights concerning equivalent properties, especially strengths.

Feb 1, 2023

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By D. R. Spears

The U.S. Bureau of Mines has had an ongoing interest in developing new reagent schemes for floating Stillwater, MT, chromite ore. Previous reagent schemes have been unsuccessful in achieving complete separation, primarily because little is known about the surface chemistry of the minerals in this ore. In order to design a rational reagent scheme, a study of the binding of various functional groups (R = -H, -OH, -CO2H, -NH2) on the two components (chromite and forsterite) of the Stillwater chromite was undertaken. Electron Paramagnetic Resonance (EPR) Spectroscopy was used to determine the adsorption isotherm, from a cyclohexane solution, of spin-probes which contained the functional group of interest. This was complemented by studies of the saturation surface coverage of the spin probe on the two minerals. In each case, more sites existed on chromite than forsterite; however, the forsterite sites were more strongly binding for each functional group. The results are discussed in terms of their implications for flotation.

Jan 1, 1994

By T. M. Gurr

In response to concerns voiced by local, state, and federal agencies and various environmental groups, the Central Florida Phosphate Industry and various governmental agencies have been investigating methods to accelerate the consolidation of waste clays generated during phosphate washing and beneficiation processes. The objectives of research efforts have been to reduce the storage volumes required for clay waste, accelerate reclamation and to return the land to approximate pre-mining topography. Government and industry research to accelerate waste clay consolidation has evolved two general methods: gravity thickening and chemical flocculation. Gardinier, Inc. one of the phosphate mining companies, evaluated the use of synthetic (polyacrylamide) flocculants as an alternate waste clay thickening method in response to mining conditions encountered at their Fort Meade Mine and the proposed North Hardee County extension of the Fort Meade mine (Figure 1). After considerable research and evaluation, the Alsthom-Atlantic Clariflux Super-flocculation method was chosen by Gardinier, Inc. as a method to seriously consider for use at their Fort Meade mine.

Jan 1, 1986

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By David M. Koogler

If you are contemplating starting a small coal mining operation there is a good possi¬bility that you can not afford it. If you, have already started, you may be on the road to bankruptcy. If you are a small but well established operator you may be trading dollars, or even dissipating your capital, equipment and other assets. A bleak outlook? Yes! Meant to be discouraging? No! Just a reminder that, with todays costs of doing business, high interest rates, rapidly increasing costs and decreasing sales prices, a small businessman/miner had best watch closely or he will be mired in something worse than a soft bottom - namely a cash and credit shortage, and in too many instances In recent times, bankruptcy. We will not dwell on what happens once you are that far gone, though I could cite a good example. But, let us look at what should be done to avoid such a catastrophe.

Jan 1, 1981

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime's shares and manages and operates the mine on Prime's behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999