Search Documents

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By R. M. Schuster

This study attempts to compare the costs of transporting coarse coal by pipeline, versus the more conventional use of belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation of this technology will become more acceptable. Hydraulic transport by pipeline between the mine stockpile and the coal preparation plant, for distances normally considered practical for an overland belt conveyor, should be an ideal application. In this application there is no need for dewatering facilities at the receiving end of the pipeline, because, the receiving screens at the plant serve this purpose. Further, clarified water from the preparation plant can be recirculated back to the mine, a plus for water resource and environmental considerations.

Jan 1, 1982

By John C. Brower

The purpose of this paper is to examine the Gays in which- the policies of the U.S. government, mining companies and third world countries affect each other with regard to the availability of minerals. The interaction involves U.S. policy towards the mining industry, the policies of the companies themselves, and the policies of third world countries towards the U.S. and multinational companies. It is assumed in this discussion that U.S. policy will continue to be to seek certain minerals from abroad rather than attempt to develop domestic sources for all its requirements. This would seem to make sense both from the standpoint of cost, and for preserving what domestic resources there are so as to maintain some degree of market leverage. In today's jargon, this means greater dependency on the "third world", which, for this discussion, includes virtually all the nations in Africa, South America and Asia. Concern for availability raises the important distinction between dependency and vulnerability, and as the Director of the Bureau of Mines has pointed out, the two are not the same. Dependency is not neccessarily a bad thing; it is vulnerability that counts (Norman, 1980)

Jan 1, 1982

By James T. Baxter

Underground mining of limestone is becoming increasingly attractive in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by edits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, St. Louis, Salem, Ullin, and basal Burlington Limestones of Mississippian age and in the Moredock Limestone Member of the Dunleith Formation of Ordovician age are possible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1978

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By A. Aly Selirn

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits and the cost of producing it as a function of the deposit parameters. The economic simulation model includes models of fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. it is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation

Jan 1, 1977

By Arcy R., D&apos George

Removal of S02 from smelter gases is being investigated, using an innovative technique that results in the almost simultaneous recovery and production of elemental sulfur. S02 is removed from the gas stream by scrubbing with suitable aqueous salt solutions or high-boiling organic fluids. The S02-laden liquor is then reacted with H2S Crystalline, high-purity sulfur is instantly precipitated and, after filtration, the regenerated liquor is recycled. The H2S required for the process is produced by reacting a portion of the recovered sulfur with hydrogen or with methane and steam. The chemistry and results of preliminary laboratory research are discussed.

Jan 1, 1969

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992

By J. J. Renton

The iron disulphide minerals, pyrite and to a lesser extent marcasite, are ubiquitous to coal and coal associated rocks and are the source of nearly all the environmental problems associated with the mining, processing and utilization of coal. The iron disulphides as well as the other minerals in coal exhibit systematic spatial pat- terns of distribution on both regional and local scales and show predictable associations, most of which are determined by the geochemical-sedimentological controls under which they form. It is the purpose of this paper to discuss the geochemical-sedimentological conditions responsible for the formation of coal minerals with special emphasis on the formation of iron disulphides, to illustrate the regional and local patterns of mineral occurrence within coal, to present the microscopic associations of the iron disulphides and finally, to discuss the most important single environmental aspect of the iron disulphide content of coal and coal associated rocks; the production of acid mine drainage.

Jan 1, 1986

By Julio C. Martinez, Jeffrey L. Rice, Hayden Weschler

This paper details the extensive underpinning required to hold up the 39th street Bridge while demolishing its massive support piers and building a 30ft deep Cut/ Cover RR tunnel beneath it. The underpinning/SOE support required the construction of 16 large hand dug pits 36ft deep that were reinforced and concrete filled. In addition, an extensive steel support system was tied into the bridge super structure. All of the underpinning/tunnel construction was done while a 110ton crane sat directly atop the heavily trafficked – 66 ft. wide bridge. The tunnel excavation, concrete lining and final bridge pier support work will also be presented. All work was done within 5ft of active mainline tracks and that required tight grouting behind all lagging to eliminate any track settlement.

Jun 13, 2021

By M. K. McCarter

A unique telemetry system was developed to monitor potentially unstable natural slopes above a residential area. Continuous interpretation of data transmitted from remote movement-sensitive devices and immediate communication of signficant changes to emergency personnel were made possible by a readily available "home" computer. Even though the computer based system was originally developed for a non- mining application, it could be used with little or no modification to monitor ground control instrumentation in open pit and underground situations.

Jan 1, 1985

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez, Nishan Pokhrel, Lizeth Jaramillo

This paper presents a case study of respirable dust characterization in a thin-seam coal mine in southern West Virginia. Samples were collected in various locations within the mine and analyzed using scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), thermogravimetric analysis (TGA), and Fourier transform-infrared (FT-IR) spectroscopy. The study found high non-carbonate mineral content, particularly aluminosilicates and silica, in the dust. The results indicate that fine aluminosilicate particles may interfere with SEM-EDX analysis, leading to an underestimation of coal content. The findings highlight the importance of using multiple analytical methods to accurately characterize respirable coal mine dust.

May 5, 2022

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

"Metallurgical process development in greenfield projects must define the comminution flowsheet and establish the equipment sizes that are required to deliver the project design criteria. These are critical steps that heavily influence the financial performance of the project, requiring a detailed understanding of the ore properties of the project resources and the best practice methods to size comminution machines. This paper reviews current practices for determining the ore characteristics relevant to comminution circuit design. Particular attention is given to the design of sampling and testing programs, and the methods commonly applied to size crushers and mills for conventional size reduction applications in mineral processing. IntroductionMetallurgical process development in greenfield projects requires the selection of a comminution flow sheet and must establish the equipment sizes required to deliver the project design criteria. This necessitates a detailed understanding of the ore properties that define the project resource. For brownfield projects the same objectives may apply for plant expansions, or the project objective may be simply to define the capacity and operating cost of an existing facility for a new ore source. The process development phase in either instance will typically comprise the following key activities:• Geometallurgical classification and sampling of the ore deposit or deposits.• Determination of comminution energy requirements.• Benchmarking similar projects.• Identification of flow sheet options.• Equipment selection and sizing.This paper is concerned specifically with process development testing and will as such focus on the first two activities on the list: sampling and testing of the deposit. The discussion will focus on testwork programs to support the design of comminution circuits commonly in use in mineral processing today, specifically crusher, tumbling mill and stirred mill technologies.It is important that any testwork program is designed giving consideration to the types of flow sheets that are viable for the project, and the data that will need to be generated to support the final equipment sizing. Designing a testwork program to only provide information about one particular type of flow sheet will not allow sufficient information to be generated for a rigorous trade-off analysis of options, and may therefore preclude financial optimization of the project. Testing programs should be designed to collect sufficient data to ensure that any backtracking at a later stage to fill in missing information is minimal."

Jan 1, 2016

A comparison of gold, platinum and sulfide ion selective electrodes was made in this investigation for determination of Eh in solutions containing sulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. In addition, the sensitivity of each electrode towards changes in sulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration of sulfide ions. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion, HS-, concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion, S-, activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of sulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1990

By Mark L. Bricker

The Jim Bridger Coal Mine, operated by Bridger Coal Co., is located in Sweetwater County, WY about 56 km (35 miles) northeast of Rock Springs. Bridger Coal is a joint ven¬ture between Nerco Coal Corp, the operator, and Idaho Energy Resources Co. The permit boundary encompasses more than 81 km'- (20,000 acres) on the western side of the Continental Divide. Since the mine began opera¬tions in 1974, it has produced about 82 Mt (90 million st) of coal while moving about 344 hm3 (450 million cu yd) of virgin earth. Annual production averages 4.5 Mt to 6.4 Mt (5 million to 7 million st) of run-of-mine coal. Coal is consumed on-site by the Jim Bridger Power Plant, a 2000-MW generating station. Electricity is transmitted to the Pacific Northwest power grid that includes Oregon, Idaho and northern California. Geology The mine is located on the northeast flank of the Rock Springs uplift. This is a broad, asymmetrical anticlinal feature about 97 km (60 miles) long and 56 km (35 miles) wide with a north-trending axis. This uplift separates the Green River Basin to the west and the Great Divide and Washakie Basins to the east. Precambrian rocks on the apex of the uplift are estimated to be 5200 m (17,000 ft) above the Precambrian rocks in the Green River and Washakie Basins. Normal faults with generally less than 30-m (100-ft) vertical displacement cut through the uplift. The dip of strata on the flanks is generally between 3° and 15°.

Jan 1, 1991

By Peter J. Szabo

In 1980, a caravan of representatives of Japanese trading companies debarked on the shores of the United States bearing gifts of watches, electronic games, and radios. In early 1983, we find in a parking lot of a major U.S. coal company, a haggard general manager of marketing returning to the Orient with a box under his arm of trinkets of his own; cross pens with company logos, alarm clocks, etc. The tables have turned, but our fellow sitting in a jet plane over the Pacific Ocean had only to heed the warning of the famous 19th Century poet well familiar with the ways of the Far East. Kipling said; "And the End of the Fight is a tombstone white and with the name of the late deceased, And the epitaph drear, a fool lies here who tried to hustle the East."

Jan 1, 1984

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011