Search Documents

By M. Z. Emad, M. U. Khan

"Coal mines opting for longwall mining or its variations rely on the main and tail gates for production. Stability of these entries or crosscuts is crucial in coal mining operations. Roof or strata failure can be fatal, may lead to property loss and delay in production. Failure of the gates depends upon many factors including the mining method, panel dimensions, pillar width, mine depth, caving rate, dimensions of gates and roof strength properties. In Pakistan coal is mined through a variation of longwall mining method with almost no mechanization while using timber as a primary support. Timber support as chock is very useful in coal mines especially in overhanging face. Similarly gate entries and coal faces are supported by chock supports throughout their length. In this paper the stability of the longwall gate is assessed for a typical coal mine in Pakistan by using finite element code. Numerical modelling considerations for gate entries are discussed. A model parametric study is performed for key factors. The results showed that the existing mining practice is not suitable and there is a need to review the mining approach. INTRODUCTION Main and tail gate entries leading to longwall mining panel play a crucial role in production cycle. Failure of any of these may lead to loss of life, property and production delays. The stability of gate entries depends primarily on the nature of loading and stresses incurred. It is relatively easier to assess the ground response to production for common longwall mining panel. In thin-seam coal mines the gate entries are generally supported throughout their length by timber made chock supports. The tailgates receive huge deformations and stresses during the mining and backfilling cycle. The chock supports are required to take care of rock falls leading to blockage of entries causing production delays and loss of capital. A number of supports are available for supporting the gate entries (Hoek and Brown 1980; Brady and Brown 1985). The support system can be selected based on load-deformation characteristics including the yielding behavior, pre- and post-yielding behavior (Barczak, 2003). The principal of support selection is that the support characteristics must match the ground response in order to maintain the gate entries (Mucho, et al., 1999). It has been observed that thin-seam mining (<1 m) is very challenging and it is necessary to develop an understanding of ground mechanics before the selection of an efficient support system Dolinar (2003). The chock supports have been tested for load-deformation characteristics in the laboratory (Barczak 2003). But the ground and support interaction, response and loads must be assessed for individual site. This can be accomplished by in-situ testing and observations at few locations. The generated data is generally insufficient for complete understanding. Numerical models can combine the data generated in the laboratory and on-site to fulfill the requirements."

Jan 1, 2017

By J. Marsden

Lift height, overall heap height and climate all play an important role in determining precious metals leaching rates, recoveries, operating costs and capital cost requirements for heap leaching operations. The effects of these factors are not easy to predict from testwork, and this can result in unexpected delays in metal production, lower recoveries than expected and higher capital and operating costs than necessary. This paper investigates the economic impact of lift height, overall heap height and climate on heap leaching and provides criteria to assist in the design and operation of leaching facilities. Descriptions of three heap leach operations in the western USA are provided to support the discussions and conclusions.

Jan 1, 1995

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By Michael J. Beus

This paper describes research conducted under the BuMines&apos;s Advancing Metal and Nonmetal Mining Technology Program, a major element being the application of new and improved technology to shaft design in deep underground vein-type mines. Two basic design parameters considered in shaft planning are configuration (shape) and ground support. The most common shapes are circular and rectangular. Ground support systems include concrete, timber sets, steel sets, rock bolts, and steel liners. The inherent advantages and/or disadvantages of various shaft designs such as ventilation and fire resistance, flexibility and ground support characteristics are well known. Circular concrete-lined shafts have minimal resistance to air flora and are virtually fireproof, an important consideration in deep hot mines. However, concrete does not yield significantly, and failure conditions and misalignment cannot be easily repaired. Timber-supported rectangular shafts predominate in the Coons d&apos;Alene Mining District with its highly stressed and frequently heavy ground. The sets can be relieved and reblocked when out of alignment. However, the constant maintenance and repair requirements result in exposure to an inherently dangerous working environment combined with excessive operating costs. Obviously a dilemma exists--a circular, concrete-lined opening has many desirable features, provided it is strong enough to withstand the stresses involved. Rectangular, timber supported shafts have proven adequate in the Coeur d&apos;Alenes; however, the implication of increased maintenance and repair requirements on ever-deepening shafts in this district and other similar areas will be an important design consideration in the future. This paper, then, presents shaft-configuration and ground-support guidelines to help remove some of the uncertainty concerning the stresses to be encountered in typical deep vein mining areas.

Jan 1, 1976

By R. Venugopal, V. K. Saxena, A. K. Mukherjee

"Coal, iron and manganese ore samples were exposed to different ultrasonic intensities of 250, 300 and 350 W/L for five minutes and to an ultrosonic intensity of 270 W/L for different time durations of 3, 5 and 7 minutes. The ultrasonically treated samples showed reductions in D80 particle diameters of 6 percent for the coal samples, 5.95 percent for the iron ore samples and 35.63 percent for the manganese ore samples during grinding. The ultrasonic treatment was also observed to assist in reducing ash content in the coal product by 8 percent and to reduce manganese losses in rejects by about 5 percent. Ultrasonic treatment was concluded to be capable of assisting in the comminution of friable ores more prominently than the hard and porous materials.IntroductionComminution is an important unit operation in the mineral-processing, cement-making, powergeneration and pharmaceutical industries. But most of the milling technologies are considered to be energy inefficient, with less energy consumed in real size reduction and most of the energy consumed in the machine. This is more critical for the mineralprocessing industry because of the growing need to exploit lower-grade ore bodies and process rejects (Blazy et al., 1994; U.S. Department of Energy, 2005). Low-grade ores require crushing and grinding to liberate the valuable minerals, which are further separated from gangues by various beneficiation methods such as gravity separation, flotation and leaching. Various studies have been carried out to minimize energy consumption during milling by developing pretreatment methods that can initiate new fractures or improve the fracture density in materials before comminution. These studies were mainly focused on chemical additives; thermal, ultrasonic and microwave treatments; and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman, Briggs and Kojovic, 1997; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Kumar et al., 2010; Wang, Shi and Manlapig., 2011, Singh et al., 2012).The fragmentation effect of ultrasonic fields in solids has been investigated since the 1950s, and Gärtner was probably the first researcher who attempted it (Gaete-Garreton, Vargas- Hermandez and Velasquez-Lambert, 2000). Sound waves can propagate in solids in the form of longitudinal waves, shear waves and surface waves, and in thin materials as plate waves.In surfaces, fractures and interfaces, various types of elliptical or complex vibrations of the particles make other waves possible. During ultrasonic-vibration treatment, cavitation bubbles nucleate, grow and collapse, generating microjets, whose impacts on the particles initiate microcracks. The ultrasonic waves can enhance the nucleation, growth and coalescence of flaws, caused by tensile or shear stress. The mechanisms operating in the materials and inducing these stresses have been identified as spall and compression-induced tensile microcracks, nucleating at preexisting flaws. These mechanisms are driven by the shock wave and cavitation effects in the surrounding fluid (Chen, Huang and Shih, 2003)"

Jan 1, 2016

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By Yuting Xue, Mark Van Dyke, Joe Wickline

The understanding of coal mine roof lithology is a critical component in the determination of engineering solutions for roof control. Coreholes were the first technology available to determine lithology of the roof in reserve areas, but coreholes are typically drilled 500–2,500 ft apart due to their cost and sometimes reach more than $125,000 dollars per hole, depending on mine conditions. The next method developed to bridge this gap was the fiber-optic scope which is utilized in the roof at the faces of underground development. High-end fiber-optic scopes can also be costly (20,000–40,000 dollars) but are more affordable than drilling a corehole, and the information can be processed immediately to make quick roof support determinations. The fiberscope can be operated wherever a roof bolter can drill a hole, and there are no restrictions related to property owners, proximity to streams, elevation changes, etc. The latest borescoping method utilized by mining companies is the use of videoscopes. Videoscopes and all borescopes in general are limited by the lengths of the scope and the length of the borehole drilled in the mine. Videoscopes have the advantage of being able to record video while examining the roof lithology. The information can be recorded quickly underground and then be examined on the surface which allows anyone to capture the video so that a geologist can make lithology descriptions without ever going underground. In the past, videoscopes had limited resolution, a short battery life, were fragile and were relatively costly. As technology progresses, videoscopes have become more affordable, have increased battery life, and offer enhanced 1080p resolution. With the broader availability of affordable videoscopes, videoscopes can be more readily used in various mine environments at every active section underground. This paper will discuss the types of videoscopes available, the features that will aid in lithology description/identification, the deployment methods pertaining to supplemental roof support recommendations, and an advanced methodology to enhance accuracy in understanding roof lithology.

Feb 1, 2025

By D. A. Norrgran

The term "secondary recovery" has recently brought on a new meaning in view of the depletion of natural resources, energy conservation, plant optimization, and the environmental consciousness that has led to hazardous waste management, recycling, and secondary processing. Many secondary recovery processes are being developed applying mineral processing technology. Gravity separation, magnetic separation, and flotation have all emerged as implicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. Although the concept of the eddy-current separator was developed over a century ago, (Patent 400317 issued to Thomas Edison on March 26, 1889) it was not until this last decade that it gained prominent acceptance. The evolution of permanent magnets has provided a cost effective alternative for the generation of high intensity magnetic fields. High energy permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymiun-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits.

Jan 1, 1991

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By George L. Atwood

The Monsanto Company&apos;s Henry Mine is located 17 miles northeast of Soda Springs, in the southeast corner of Idaho. Ore being mined is phosphate rock which lies in the Permian Phosphoria formation. The ore is the raw material for Monsanto&apos;s three furnace elemental "P" plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. Mining is by open pit methods using 0-9 crawler tractors to rip and push-load rubber tired scrapers in stripping and mining operations. The equipment spread consists of six D-9G crawler tractors, four Caterpillar 6578 scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12-month basis, two shifts per day. Mining is performed mainly in the summer months on a one shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1,000,000 tons of phosphate rock and 2,500,000 to 3,000,000 yards of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor. Dravo-Soda Springs owns, operates and maintains all equipment used in stripping, mining and hauling. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis. The Monsanto elemental phosphorus plant began production in 1952 with ore being trucked to the plant from the Ballard Mine. Haulage was over public roads in 15, 24-ton semitrucks. A private haul road was constructed from the Ballard Mine to the Monsanto Plant in 1958 and 1959 to accommodate trucks with two twenty-yard trailers. This 11/ mile road was first used in the 1959 hauling season. In 1965, five new Kenworth tractors with two, &apos;forty yard trailers were introduced into the haulage system. These units carried 120 ton payloads and were used until

Jan 1, 1972

By Robert J. Wright

The purpose of this paper is to propose a classification of uranium deposits that is believed to be well suited to the needs of uranium exploration and resource assessment. By way of background some observations are offered about mineral exploration in general, and uranium in particular. Attention is first given to the we of models in mineral exploration. Some general principles of mineral deposit classification, the basis for model formulation, are then considered. Finally, the uranium classification is presented.

Jan 1, 1979

By Linda Frederick

In July 1997, Krupp Canada obtained the contract to design and supply the conveyor system for Chile&apos;s Los Pelambres copper mine expansion project. Progress on the overland conveyor system is currently on schedule. It is a challenging task to convey copper ore from an open-pit mine located on a mountain site 3,000 m (9,840 ft) above sea level down 1,300 m (4,265 ft) to the processing plant at the valley floor below. The Los Pelambres conveyor system moves copper ore at a rate of 8.7 ktlh (9,600 stph) and at a speed of 6 ml sec (1,180 ftlmin) for 12,750 m (41,830 ft). The distance is divided in three conveyors, each 1,800 mm (71 in.) wide. The largest conveyor is 6 km (3.7 miles) long. To protect against avalanches and rockslides, the conveyors run through a 12-km- (7.4-mile-) long tunnel system. The lowest of the three conveyors is equipped with a shuttling head end. With this, the conveyor discharge point can be moved back and forth by 100 m (330 ft), allowing it to build up a longitudinal stockpile at its end. To meet the extreme design parameters, the limits of conveyor design had to be pushed to record-setting marks. For instance, the ST-7800 steel cord conveyor belt is the strongest belt ever installed in a conveyor system. A total drive power of 25 MW (33,535 hp), consisting of 10 2.5-MW (3,352-hp) drives, is included in the design plans. In loaded condition, the electric motors act as generators and feed electric energy back into the power grid. The motors are controlled by variable frequency inverters that provide an infinite adjustment of motor speed. This technology allows starting and stop- ping the conveyors precisely along predetermined acceleration and deceleration ramps. This is done so harmful belt jerking and stress waves can be avoided.

Jan 1, 1999

By G. X. Wang

The nonliving dried water hyacinth (E. crassipes (Mart.) Solms) roots were investigated for biosorption of cadmium and lead and other heavy metal ions in aqueous solutions. Dried water hyacinth roots, when suspended in solution, strongly and rapidly sorb several different metal ions. Factors such as reaction time, pH, initial concentration of metal ions, presence of other metal ions and biomass concentration were investigated. Metal ions, including Cd2+ and Pb2+, were bound to the root in a very pH-dependent manner, with the binding increasing after about pH 3. High levels of removal were obtained. The adsorption was shown to follow the generalized Langmuir adsorption equation. The relative affinity of the roots for lead is greater than for cadmium. The maximum sorptions of the roots were about 33 and 86 mg/g for cadmium and lead, respectively. Only 15-20 minutes were required for the process of uptake onto the biomass to occur. The batch sorption kinetics of the uptake of cadmium and lead can be described by an apparent first-order reversible reaction model. The roots could be regenerated after the metal ions were stripped. A solution of CaCl2 in acidic medium appeared to be the best eluant for desorbing the sequestered Cd and Pb completely at pH 3. The kinetics of the metal stripping process was quite rapid. Successful desorption of Cd and Pb from the biomass by acidic CaCl2 solutions revealed that the metal uptake phenomenon is reversible, implying physical sorption of Cd and Pb.

Jan 1, 1997

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By Hans von Michaelis

The current exploration boom in Central and South America shows no sign of abating and, if anything, is growing. This is despite an inevitable cooling in the recent frenzied buying of resource stocks on the Canadian exchanges which have funded much of the Latin American exploration. Several factors appear to be driving the boom. Firstly, the resource potentials in this vast under-explored regions are nothing short of phenomenal. Secondly, after decades of stifling nationalization and restrictions that stood in the way of foreign investment, especially in mining, emerging nations the world over now suddenly find themselves competing with each other to be the most attractive.

Jan 1, 1995

By Basar Arioglu, Jaeung Kim, Mehmet Öztürk, Jinmoo Lee, Dongho Lee, Taek-Kon Kim

"Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) includes 3.34 km of a bored double-deck tunnel under the Bosphorus Strait, at a maximum depth of 106 m from the sea level, and 1 km of twin NATM tunnels on the Asian side. The region’s variable geology, hydrology and propensity for seismic activity, combined with high water pressure and large-diameter/double-deck tunnel configuration, make the Eurasia Tunnel one of today’s most challenging and complex projects under construction. Due to the site’s proximity to the active North Anatolian Fault, the tunnel is designed to withstand a 7.5 magnitude earthquake. The tunnel penetrates through both the Trakya bedrock (on both European and Asian sides) and the alluvial sediments at the bottom of the channel. The tunnel is designed to accommodate differential displacements by introducing seismic/flexible joints at proper locations at the transition zones between rock and soft soils. Tunnel fire is also a significant design consideration for undersea tunnel due to that the rubber protecting it in close proximity of the seismic joint should resist a fire for long term safety and durability. This paper mainly focuses on the design for method of tunnel response analysis in transverse and longitudinal direction against seismic demands relating with the seismic joints. INTRODUCTION Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) will build and operate a roadway tunnel under the Borphorus connecting Kazlicesme on the European side and Goztepe on the Asian side, to provide additional road-access across the Strait and consist of three main parts as shown in Figure 1."

Jan 1, 2016

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant&apos;s performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014