Search Documents

Recent expansion programs have made the Yunkang underground coal mine the number one producer in Shenxi Province. The mine is the newest in the Datong Coal Administration, currently rated at around 3 Mt/a of coal. Located in the Wa Chushi mountain range about 23 km north of the city of Datong, the mine has undergone a series of expansion phases since startup in 1973. Initial design capacity was 1.5 Mt/a and ultimately, production will be brought to an estimated 7.0 Mt/a by 1985, according to mine superintendent Li Jia-zhi. How Coal Occurs The coal, Jurassic in age, occurs in three economically identifiable seams designated No. 2, 3, and 7. Seams are 100-250 m below the surface. Reserves from this economic zone were not quantified, but Superintendent Li indicated that there was enough mapped out to sustain the expanded production rate for over 20 years. Below the Jurassic coal is another possible economic zone, a Permocarboniferous coal lying 400-600 m below the surface. Little development drilling has been conducted to ascertain its potential. The Jurassic beds are relatively flat and coal quality is reportedly one of the best in China. Heat content of the coal runs around 33.5 MJ/kg and the ash content is less than 10%. In some areas, it is less than 7%. Coal preparation is simple and involves a washing and screening separation into four principal size fractions. Washed coal is stored in one of six storage silos, each with 4000-t capacity. Mining the No. 2 Seam Since startup, primary production has been derived from the No. 2 seam. The coal is relatively hard and is topped by a hard cement-like conglomerate. These factors, coupled with an average thickness between 4 to 6 m, precluded the use of conventional longwall techniques, according to mine engineers. The solution was development of a room-and-pillar tech-

Jan 3, 1980

By Vas P. Kenyen

Introduction Autogenous, semi-autogenous, and conventional grinding circuits are used to process ores. Current emphasis, though, is towards the use of the first two systems. The reason is the generally lower initial investment required for an autogenous or semi-autogenous circuit as compared to a conventional comminution circuit. However, the effect of operating costs that will significantly affect overall comminution economics is not considered in this evaluation. About 70% of the energy in a mineral processing plant is used in the comminution circuit. Until the 1974 oil embargo, energy was relatively inexpensive. Since that time, the cost of energy has escalated 40-fold. As a result, energy cost now forms a significant portion of operating costs in comminution. According to a survey conducted by General Electric Co. (Powers, 1982), the price of electricity will continue to rise 15% to 20% per year, in spite of the current oil glut. Both autogenous and semi-autogenous grinding circuits consume more energy than the conventional comminution circuit. Higher consumption ranging from 16% to 35% has been reported in the literature (Bassarear, 1982; Gjerdrum. 1979; Betts, 1982; and Christie, 1979). Consequently, even a small increase in energy costs is likely to have a significant impact on operating costs. Therefore, the economic decision of selecting an optimal comminution circuit is important. More than ever before, it is now critical to include in the evaluation of communition circuits not only the capital costs, but also the operating costs; in particular, the expected energy cost over the life of the operation. Failure to do this may lead to a less than optimal comminution circuit. Design A comminution system should be designed only after bench-scale or pilot plant testing of a representative sample. Conventional crushing and grinding circuits can be designed on the basis of the Bond Work Index (Rowland and Kjos, 1980). Over the years, sizing of full-scale rod and ball mills from Bond Work Index data has become well established. Autogenous and semi-autogenous mills cannot be sized based on bench-scale tests. Pilot plant tests are necessary to determine the amenability of the ore, critical size buildup, and power requirements. For this study, conventional and semi-autogenous grinding circuits were designed for ore throughput of 12, 24, 36, 48, 72, and 90 kt/d (13,200, 26,400, 39,600, 52,000, 79,200, and 99,000 stpd). Rod and ball mills were scaled up on the basis of the Bond Work Index. A two-stage semi-autogenous grinding circuit was designed on the basis of pilot plant test results. In designing a grinding system, emphasis was placed on operating flexibility. The largest commercially available equipment was

Jan 10, 1984

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the roof bolter canopy air curtain (CAC) designed by the U.S. National Institute for Occupational Safety and Health (NIOSH) has gone through many iterations, demonstrating successful dust control performance under controlled laboratory conditions. J.H. Fletcher & Co., an original equipment manufacturer of mining equipment, further developed the concept by incorporating it into the design of its roof bolting machines. In the present work, laboratory testing was conducted, showing dust control efficiencies ranging from 17.2 to 24.5 percent. Subsequent computational fluid dynamics (CFD) analysis revealed limitations in the design, and a potential improvement was analyzed and recommended. As a result, a new CAC design is being developed, incorporating the results of the testing and CFD analysis.IntroductionExposure to respirable coal mine dust can cause coal workers’ pneumo-coniosis (CWP), also known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is to eliminate exposure to respirable coal mine dust and crystalline silica, or quartz. The occupational exposure limit on a Mining Research Establishment (MRE) basis for respirable coal mine dust had been 2 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities. Under recently enacted legislation, this standard was changed in August 2016 to 1.5 mg/m3 for a full working shift (The Office of the Federal Register, 30 CFR 70.100, 2015). When respirable quartz is present, the mine must maintain its average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percentage of quartz present (The Office of the Federal Register, 30 CFR 70.101, 2015).The sources of exposure to respirable coal mine dust for roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind — in the return air — of the continuous miner (Good-man and Organiscak, 2003). Recent studies have demonstrated that vacu-um dust collection systems are effective in capturing bolter-generated dust if maintained and operated correctly and if proper face ventilation techniques are used. However, most expo-sure to respirable coal mine dust for a roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner (Potts, Reed and Colinet, 2011; Colinet, Reed and Potts, 2013). Because of this higher exposure downwind of the continuous miner, the roof bolter is often limited to working downwind of the miner only once during a production shift."

Jan 1, 2017

By L. A. Rapoport

This paper outlines the methodology and results pertaining to the simulation of the U.S. coal industry in the context of an integrated, time-dynamic model of Long-Range Energy Developments and Supplies (LORENDAS). By way of background we will present first an overview of the overall LORENDAS model structure. We will, then, outline the characteristics of the formulation and data used for the representation of the U.S. coal industry. Finally, a series of model results will be reviewed, with particular emphasis on the long term projections of coal production and distribution under different basic economic and/or political scenarios.

Jan 1, 1977

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. High-grade Transvaal chalcopyrite was neutron irradiated in a TRIGA reactor to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes during which time significant anomalies were observed. First, an initial period of rapid dissolution lasting a few minutes; second, an arrest or "plateau" region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effect of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured. The initial rate data were correlated by considering the rapid reaction to be due to the dissolution of surface oxidation products or the formation of an iron depleted surface layer. The data for the second slower reaction have been explained to be due

Jan 1, 1972

By S. Frimpong, E. Siami-Irdemoosa, S. R. Dindarloo

"Electric and hydraulic shovels are the dominant loading machinery in surface mining operations. Despite their critical role in production and their high capital and operating costs, no reliable and comprehensive quantitative performance metric is available. In this paper, a stochastic shovel effectiveness (SSE) measure is proposed for the purpose of quantifying the performance effectiveness of these shovels. The SSE is based on the widely used method of overall equipment effectiveness (OEE) in the manufacturing industry. The OEE measures the performance effectiveness of equipment by multiplying its mechanical availability, utilization and production quality. In manufacturing processes, quality rate is the ratio of the total number of products minus the number of defective products – equivalent to the number of acceptable products – to the total number of products. The SSE similarly uses the mechanical-availability and utilization terms, but instead of quality rate it uses a new parameter named bucket rate.The variability or randomness of the input data, that is, availability, utilization and bucket rate, are further incorporated into the SSE, and a final stochastic SSE distribution is derived in the form of a probability density function. One hydraulic and one electric shovel in a surface mining operation were selected to test the validity of the proposed method. The SSE scores for the two shovels, operating continuously for one year, were derived and compared. As with the OEE, the three-parameter SSE method yielded more representative results for overall performance measurement than a single-parameter approach. Using Monte Carlo simulation, a three-parameter Weibull and a normal distribution were derived for quantifying the overall effectiveness of hydraulic and electric shovels, respectively. As a decision aid, the proposed methodology promises to render a more informative tool than traditional metrics for mine equipment maintenance and management."

Jan 1, 2015

By Dean Newman, Michael Behrens, Mark Trim, Justin Arifin

Road tunnels in recent infrastructure projects in Sydney, Australia, are designed to have a fire resistance level of either a 4-hour cellulosic fire or a 2-hour hydrocarbon fire. Where permanent ground support for tunnels consists of systematic rock bolts and relatively thin layer of shotcrete, it is important to ensure that during and after the fire event the ground support is designed/predicted not to pose risks to the tunnel occupant. The global behavior of the ground support can be predicted using finite element analysis, and its resistance is derived with consideration of the material strength degradation due to the elevated temperature.

Dec 1, 2022

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By R. K. Dunham

It has been estimated that 30% of the United States coal reserves occur in the Western States at depths which would preclude exploitation by surface techniques. Much of this coal occurs in seams considerably thicker than those presently mined in other parts of the country. Recognizing the lack of technology and experience in exploiting the thicker seam range the Interior Department's Bureau of Mines is implementing a major "Mining System for Western Coal," research program which has as its ultimate objective the development and demonstration of underground mining methods and technology for extracting these seams. One investigation, being carried out by D'Appolonia Consulting engieers, under contract to the Bureau of Mines, is concerned with design of an entry system for longwall top slicing of thick western coal seams. This presentation presents an overview of some of the problems which have to be faced in designing such layouts.

Jan 1, 1977

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF's) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modeled with conditional simulation, which generates multiple possible realizations of grade that are equally probable (or improbable). M ethods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time-consuming. This paper proposes a simple and efficient modeling approach to incorporating conditional simulation into pit optimization, which would be able to be applied in currently commercially available software. An example for R esolute M ining Ltd.?s Syama gold project in M ali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Jan 1, 2013

By Tony Dunn

FMC Corp. achieved a significant cost reduction at its Green River, WY soda ash operations using a new proprietary solution-mining and processing technology. In phase one of the program, trona ore is dissolved, recovered and processed with the new technology. It is then fed into an existing refining plant, replacing dry mined and calcined trona ore. Phase two produces a final high-purity product. It also increases capacity by 635 kt/a (700,000 stpy). Both phases were completed under budget and ahead of schedule. This $120-million expansion project uses a new process and a new team to derive soda ash in a more cost-effective and environmentally friendly manner. The team successfully introduced solution-mining technology - with a liquid solution injected into previously mined sections of the mine. This shift in techniques signified a new era for soda ash production. The project is an example of teamwork at its best. For it to be successful, FMC had to work within several different areas inside and outside of the company. Engineers, contractors, mechanical operators and technical people were needed who could blend in with FMC's existing in-house team.

Jan 1, 1999

By W. B. Lambert

A common decision in openpit mining is to determine the extraction sequence of notional three-dimensional production blocks so as to maximize the net present value of the extracted orebody, while adhering to precedence and operational resource constraints. This openpit block sequencing (OPBS) problem is commonly formulated as an integer program, with binary variables representing if and when each block is extracted. In practical applications, the number of blocks can be large and the time horizon can be long; therefore, instances of this problem can be difficult to solve using the exact approach of optimization. The problem is even more challenging to solve when it includes explicit minimum operational resource constraints. Our maximum value feasible pit (MVFP) algorithm generates an initial integer feasible solution for OPBS problems, in which minimum operational resource constraints are strictly enforced. As an exact approach, we present a Tailored Lagrangian Relaxation (TLR), in which the selection of constraints to dualize is guided by information provided by the MVFP algorithm. We present results and graphics to demonstrate the utility of our techniques for instances containing up to 25,000 blocks and 10 time periods.

Jan 1, 2013