Search Documents

By M. Tamlin

The state of the lithium mineral industry is closely linked to the performance of the glass and ceramic industries and to the overall economy. Demand for the glass/ceramic products in Europe, Asia and North America remained strong during 1999. This was due to a slight improvement in the economy during the latter half of the year. Consequently, demand for lithium minerals was firm, with a positive outlook. The major economic minerals for lithium are spodumene, petalite and lepidolite. The latter was once the primary mineral. But its importance hasdeclined since the 1960s. The lithium industry consists of two different segments: •The lithium minerals segment mines from hard-rock deposits and physically processes the material to high-grade concentrates. •The lithium chemicals and metal industry segment. The major feedstock for specialty lithium chemicals was previously high-grade spodumene ore converted to lithium carbonate. However, most lithium carbonate is now sourced from salars in North and South America.

Jan 1, 2000

By M. J. Ross, D. A. Norrgran, J. A. Wernham, J. N. Orlich

INTRODUCTION Laboratory testing for magnetic concentration circuit design is a requirement, just as it is for most other types of concentration. Natural variations in raw materials allow on1 y the broadest of generalities to be made regarding magnetic separation. Further, magnetic fields are geometry dependent, leaving fundamental models of a separator overly dependent upon the exact conditions for which the models were derived. Despite this, an understanding of the basics of magnetic separation and of the problem to be attacked can result in rapid progress towards the final circuit design with a relatively simple testing program. Magnetic Separation Basic Principles A magnetic field can readily be understood in terms of lines of flux. A familiar demonstration of these lines of flux is the pattern of iron filings on a sheet of paper when a magnet is placed underneath. Lines of flux2 are measured in Gauss (1 line/cm2) or Tesla (10000 gauss). Regions of high field strength have a greater number of lines. Field direction is indicated by a convergence of lines. When a particle is placed in a magnetic field it cuts the lines of flux and alters them in one of three basic patterns. These patterns are referred to as diamagnetic, paramagnetic and ferromagnetic. Diamagnetic materials have electronic structures which react to oppose an applied magnetic field. This opposition acts to locally reduce the applied field slightly. The visualization is that lines of flux diverge and go around the particle. Because of this divergence or opposition, a diamagnetic particle will tend to move towards regions of lower flux density. That is to say that the particle will be repelled by a magnetic field. Aluminum oxide and napthalene are examples of diamagnetic materials. Paramagnetic materials have an electronic structure which increases an applied magnetic field. Although these materials also exhibit diamagnetism, they have randomly oriented impaired electrons which align with the magnetic field. The resultant local field enhancement is significantly larger than the diamagnetic opposition. The visual-

Jan 1, 1986

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors' records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi

The abstract highlights the impact of flocculants used in the middle thickener of a copper-molybdenum plant on both process water quality and molybdenite floatability. The study investigates the effect of a starch-based flocculant (wheat starch) on the efficiency of the middle thickener and molybdenite flotation. The findings indicate that the presence of starch influences the settling behavior of particles with different shapes, and the dosage of starch affects both molybdenum recovery and the presence of copper minerals in the molybdenum concentrate.

Mar 7, 2022

By Ali Soofastaei

Mining operations are increasingly data-rich yet decisionconstrained. Fragmented systems, variability in geology and operations, and sustainability obligations create multiobjective trade-offs that classic analytics cannot reconcile at operational tempo. This paper proposes an end-to-end framework that fuses digital transformation practices (governed data platform, semantic layer, feature store, and MLOps) with generative AI (retrieval-augmented generation, tool-use, and agentic workflows) and decision intelligence (simulation/digital twins and multi-objective optimization). We formalize sustainability-aware objectives, define a practical stack and governance controls, and demonstrate how an AI “decision copilot” can surface options, quantify trade-offs, and document rationale. Two figures illustrate a production-grade architecture and a Pareto frontier for cost–emissions trade-offs; two tables operationalize decision-domain mapping and a transformation maturity rubric. The approach is product- and company-agnostic.

Feb 22, 2026

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

By Fabio Mielli

Encompassing between 20 and 40 percent of the typical mining operational costs, energy in mining operations is a growing concern for the industry. However, this concern is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. Managing energy efficiency is becoming a keystone of successful companies. The suggested energy strategy in mining and mineral processing operations must follow a well-structured approach to include the following: ? Understanding where energy is being used and why. ? Recommending and implementing energy conservation measures. ? Driving visibility to targets and results. ? Leveraging the energy spent across the enterprise. ? Developing a robust energy and sustainability strategy. Additionally, it must ensure that all decisions support the financial and operational integrity of the business.

Jan 1, 2012

By James F. Fraser

Construction of a major linear project in any environment is difficult, at best. Construction of a major linear project which includes major subway elements, both cut and cover and tunneling, in the center of an urban environment, approaches the impossible. I believe such a project would be impossible for a private company or a privately owned utility for a variety of reasons. The major two reasons are the funding necessary for such massive projects and the myriad of individual interests associated with private ownership of land. Such projects are possible in the public sector only because the need for the project... as is the case with mass transportation in Atlanta. . .overrides the profit motive. Without the profit motive, private companies, whether utilities or not, are precluded from practical interest in the development of any project. While it is safe to conclude that a profit-oriented business would have no practical interest in developing such massive projects as may include major tunnels, it would be useful, I think, to compare some of the significant differences between private profit-oriented businesses, and an agency, or Authority, such as MARTA, in building a major linear project. SLIDE 1. Comparison of a Private Company and a Public Agency [Item Private Company Public Agency Simplified To make a profit To provide a pre Purpose scribed service]

Jan 1, 1979

By Michael L. Ogilvie

The proportion of underground coal production as a percentage of overall Australian production has fallen in the last 10 years, with underground production remaining more or less static at about 53 Mt (58 million st). However, underground coal mining remains a viable industry in Australia, due to use of modern longwall mining systems. In 1993-1994, 26 longwalls were in operation, with total production exceeding 39 Mt/a (43 million stpy). Some of these longwalls achieve productivity levels approaching efficient opencut operations, and in some cases, they exceed them. These high-production longwall mines are not without problems when depth and distances from outcrop increase and the gas content of the seams approaches or exceeds critical limits. When gas content of a coal seam exceeds 6 m3/t (233 cu ft/st), gas flows into the mine may be sufficient to interrupt production from time to time.

Jan 1, 1995

By S. S. Klima, J. A. Organiscak

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed laboratory testing to examine and improve airborne dust capture and methane removal performance of flooded-bed scrubbers on continuous mining machines using a blowing face ventilation configuration to reduce respirable dust exposure to shuttle car operators. Several testing conditions were examined to minimize shuttle car operator dust exposure without adversely affecting continuous miner performance and production. Curtain-to-face setback distance of 9.1 m versus 15.2 m (30 ft versus 50 ft), face ventilation airflow of 226.5 m3/min versus 339.8 m3/min (8,000 ft3/min versus 12,000 ft3/min), and the use of side-body-mounted blocking sprays (on versus off) were the three primary parameters compared. Scrubber airflow was set and maintained at 198.2 m3/min (7,000 ft3/min) throughout testing. An examination of slab cuts versus box cuts and the location of the shuttle car (present behind the continuous miner versus not present in the entry) was also performed to demonstrate the effects of these constantly changing scenarios on scrubber performance. Results show that the best blowing face ventilation setup for minimizing shuttle car operator dust exposure for the tested parameters uses a 15.2-m (50-ft) curtain-to-face setback with 339.8 m3/min (12,000 ft3/min) face ventilation while operating the side-body-mounted blocking sprays. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in U.S. underground coal mining operations, potentially leading to coal workers’ pneumoconiosis (black lung). The U.S. Mine Safety and Health Administration (MSHA) requires that respirable dust exposure to coal mine workers does not exceed a 1.5 mg/m3 average over the actual working shift (79 Fed. Reg. 24814 (2014)). Although using a blowing face ventilation configuration on continuous miner (CM) sections is beneficial for removing methane emissions from the mining face, it can be detrimental for dust control for shuttle car (or ram car) operators and any other workers on the return ventilation side of the CM when compared to exhausting ventilation. Even with machine-mounted scrubbers on CMs, shuttle car operators still have some of the higher dust exposures with blowing face ventilation systems (NIOSH 2011, Beck et al. 2015). Although scrubber discharge air is not completely clean, dust being blown around the scrubber inlet and therefore not being captured by the scrubber can further increase these dust exposures (Goodman 2000). Dust control problems are also caused by inadequate face ventilation quantities causing scrubber face airflow recirculation issues (Schultz et al. 2010). In order to minimize respirable dust exposures on blowing face ventilation sections, ventilation, water spray, and scrubber parameters were experimentally examined to improve operating ranges for both dust and gas control. Several blowing face ventilation factors were examined with respect to CM spray systems and scrubber operation. Curtain-to-face setback distance and side-body-mounted blocking sprays were previously examined in the laboratory for dust control on a full-scale CM model using a scrubber on a blowing face ventilation system (Goodman 2000). The blocking sprays produced larger dust reductions at the CM’s rear corners and return for a 6.1-m (20-ft) curtain setback distance as compared to a 12.2-m (40-ft) curtain setback distance with equal face and scrubber airflows of 169.9 m3/min (6,000 ft3/min). Because face ventilation airflow quantities, shuttle car operator locations, and tracer gas concentration gradients were not previously examined during these experiments, additional research was required to determine improved operating parameters for blowing face ventilation systems.

Jan 1, 2019

By Sunil Vytla, Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes (carbon monoxide and nitrogen dioxide) clearance and workplace reentry time have overlooked the effects of toxic gases trapped in the muck pile. The currently available models for calculating the mine reentry times assume that all post-blast fumes are emitted upon detonation. However, recent studies reported that as much as 60 to 70% [1–5] of the fumes or gases produced during an underground development blasting could remain trapped in the adjacent rock mass or in the muck pile. Trapped fumes are slowly released [1–5], and when disturbed, high concentrations are released, representing a possible risk during the loading and transportation of the muck pile. In this study, mathematical models were developed using computational fluid dynamics to understand the behavior of the trapped fumes and their effect on mine reentry time. The three scenarios considered for this study include (i) gas emission source with no muck pile volume, (ii) gas emission source with non-porous muck pile volume, and (iii) gas emission source with porous muck pile volume. The estimated reentry times in all three scenarios were compared to see how porous media affects dilution time. It was observed that scenario 3, with fumes trapped in the muck pile, took a significantly longer clearance time (more than double) as compared to scenarios 1 and 2.

May 17, 2022

By Richard E. Gray

Virtually all structures show some signs of distress due to deterioration of the building components, to changed loads, or to changed support conditions. Changed support conditions result from ground movements. In mining regions many cases of structural distress are attributed to mining without considering alternative causes. This is particularly true of coal mining since it occurs under extensive areas. Coal mining is estimated to have already undermined more than eight million acres and may eventually undermine 40 million acres in the United States (HRB Singer, Inc., 1977). Other nonmetal and metal underground mines impact much smaller areas. Although it is sometimes difficult, even with careful study, to identify the actual cause of damage, persons responsible for underground coal mining should at least be aware of possible causes of building stress other than mine subsidence. This paper presents information on distress to structures and briefly reviews a number of causes of ground movements other than subsidence: Mass movements, dissolution, erosion, frost action, shrinking and swelling, yield into excavations and compressibility

Jan 1, 1986

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920's, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By R. P. Fischer

Traditionally, molybdenum and vanadium have been used chiefly as alloy metals in steel. They impart similar characteristics to most steels, and to some extent one can be substituted for the other. In the United States during the 1950's the production of steel increased about 5 percent, and the reported consumption of both of these alloy metals in steel increased some 40 percent. In Europe during the 1950's the production of steel in¬creased nearly 100 percent. Data on the actual consumption of these alloy metals in European steels are not available, but production and trade records show that the European supplies of molybdenum increased about 150 percent and those of vanadium about 350 percent during the 1950's. If most of the molybdenum supplies in Europe are being added to steel, as seems likely, then the European steel industry has nearly caught up with the United State in the rate of consumption of molybdenum in steel. The vanadium supplies, on the other hand, are puzzling--unless Europe is adding mach more vanadium to steel than is done in the United States, it seems reasonable to assume that other uses are consuming moderately large quantities of this metal or that appreciable amounts of it are being transshipped from Europe. To the extent that a changing volume of supply signifies a changing pattern of use, the increased demand for molybdenum and vanadium in Europe should be of interest to domestic producers and consumers of these metals.

Jan 1, 1964

By D. C. Torre

Ever since the early '60's there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the continuous haulage systems which have been most successful to date were placed in operation in the early '70's and were all of the bridge conveyor type, usually consisting of bridges and mobile bridge carriers attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor type continuous haulage systems were, and continue to be, either of the belted or chain type. Undoubtedly, the most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Company. Until early 1977, the most successful chain conveyor type haulage systems were manufactured and marketed by Jeffrey Mining Machinery Division. In 1977, Long-Airdox reentered the market with a chain type system to complement its belted system. I say "reentered" because the original bridge type continuous haulage system was introduced to the coal mining industry in the early '60's by the old Long Company, a predecessor of the current Long-Airdox Company, and those original units were of the chain conveyor type.

Jan 1, 1981

Automation and robotics are the keys to new intelligent autonomous mining systems which can remove operators from the hazardous and stressful mining environment and provide the tools for greater productivity. This pa-per presents the components necessary for a mining Intelligent Task Control System (ITCS) in dynamic unstructured mining environments. The proposed concept is applied to develop the ITCS for an autonomous excavator. The design and implementation of a fuzzy logic controller for an excavator that uses force/torque sensor feedback to complete excavation tasks is presented. Initial experimental results are also given.

Jan 1, 1994

By W. D. Hausel

The Wyoming craton in the western United States is a favorable terrane for diamond deposits. The craton hosts a variety of ultramafic, ultrabasic, and ultrapotassic rocks. Additionally, a few hundred 'kimberlitic' heavy mineral anomalies and some geophysical and remote sensing anomalies indicate the presence of undiscovered, mantle-derived, pipes in the craton. The Wyoming craton is separated into a Wyoming 'archon' known as the Wyoming Province, and the Colorado 'proton' known as the Colorado Province. The 'archon' underlies much of Montana and Wyoming and continues north into Alberta and Saskatchewan; the Colorado 'proton' underlies much of Colorado and a small portion of Wyoming. Although most exploration geologists would consider the 'archon' the most favorable terrane for commercial diamond deposits, the 'proton' has produced more than 120,000 diamonds, while the 'archon' has not been very productive.

Jan 1, 1996

By John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environ-mental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of environmental monitoring systems is reviewed.

Jan 1, 1977