Search Documents

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By R. Lawrence

Mineral property valuations to be used for Canadian securities regulatory purposes must comply with CIMVal1. The technical basis for a CIMVal report is the same as that required for a technical report that complies with NI 43-1012. NI 43-101 describes the content to be covered in a technical report, while also covering other requirements, one of which is that the report should be based on a property visit. CIMVal is based on five tenets that the valuator must follow: ? Materiality. ? Independence. ? Transparency. ? Competence. ? Reasonableness. Upon its adoption by CIM Council in 2003, it was hoped that the new CIMVal code would be adopted without change by the several Canadian regulators.

Jan 1, 2011

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

A thorough improvement in mine safety is contingent on many factors that require scientific decision-making for selection and prioritizing of important factors for safety improvement. Their analysis using an established scientific method can improve mines’ safety conditions and assist the administration for informed decision-making. This research establishes a mine safety evaluation index and proposes an integrative model based on the entropy weight and grey clustering methods. In the evaluation index, 27 significant factors of safety are identified and categorized into 7 criteria. The proposed evaluation system analyzes all indicators according to Pakistan’s current mine safety situation and their significance for potential safety improvement in the future. Results reveal that current safety practices are outdated due to a lack of mechanization in the mining industry and minimal capability of the management to achieve the desired safety targets. Appropriate safety policies and safety education are missing in the daily working environment. The lack of overseeing the execution of safety operations and the lack of ambition and strong work ethic workers contribute to the paucity of mines’ safety conditions. The prevention and control systems to manage risks and hazard are not in place, and the working environment in mines remain difficult. Therefore, to have enhanced mine safety, important factors can be addressed in chronological order, as presented in this paper. The proposed methodological approach can be applied to other prioritization applications to analyze the indicators and determine the appropriate management strategies.

Jun 14, 2021

By William Gleason

"Caterpillar is the largest manufacturer of mining equipment in the world. In hundreds of surface mines around the globe, Caterpillar’s flagship 793 haul trucks can be found moving material for copper, coal, gold, iron ore and other mines. Likewise, its iconic yellow bulldozers are at mine sites the world over — the company recently announced the sale of its 40,000th large dozer. And since its acquisition of Bucyrus in 2011, Caterpillar has positioned itself to become a worldwide leader in the underground mining sector as well.But don’t think that the company is resting on its reputation. As evidence of its commitment to the global mining sector, as well as its confidence in the future of mining, Caterpillar invited mining trade press, including Mining Engineering, to its Tinaja Hills Training Center near Tucson, AZ in November to introduce the latest editions to its mining portfolio. The two-day event focused mostly on the newest electric drive haul trucks, the Cat 796 AC, which will operate in the 326-t (360-st) class, and the 798 AC in the 360 t (400 st) weight class.Caterpillar representatives also spoke about new offerings in the underground space as well as the newest version of the D11 large dozer.“It has been 10 years since we launched the F Series,” Jean Savage, Caterpillar’s vice president, surface mining and technology said. “Since then, we have been on a journey to serve our mining customers and we wanted to have trucks in every application. Today, we are launching two new trucks that will allow us to fill out our portfolio.”While Caterpillar previously offered the broadest range of off-highway haul trucks to the mining industry, it was noticeably absent from the 326-t (360- st) and 360-t (400-st) weight classes."

Dec 1, 2018

By Hussin A. M. Ahmed

Oxidized coals are difficult to float. Therefore, in this paper, a special flotation procedure was investigated for upgrading this type of coal. The procedure is called direct contact flotation. It relies on mixing dry coal either with pure (anhydrous) flotation reagent(s) or microemulsion. By applying the new direct contact flotation procedure, a coal yield reaching > 95% using anhydrous flotation reagents was achieved, but with relatively high consumption of reagents (up to 30 g/kg). This high reagent consumption may be attributed to the fines included in the flotation feed (100% less than 0.5 mm, with 40% less than 75 µm). On the other hand, the clean coal yield was found to be approximately 88% when mixing dry oxidized coal with microemulsion droplets from dodecane and dodecyl tetra (ethylene glycol) ether (C12E4) in water at a total reagent dosage of 10 g/kg. The direct contact of coal either with unhydrous reagents or microemulsion also provided a high flotation selectivity.

May 1, 2012

By Joseph P. Gildner, Michael S. Kucker, Robert A. Robinson

Considerable controversy seems to exist over the extent and nature of information that should be provided in design-build type contracts. Much of this controversy may relate to the types of owners, ranging from private industry to state and federal agencies that are implementing design-build. Philosophies for the development of geotechnical information ranges from no information to a thorough investigation approaching that needed for final design. Several recent projects, such as the Channel Tunnel in Europe, Whittier Tunnel in Alaska, Tren Urbano in Puerto Rico, and Sound Transit in Seattle have taken varying approaches to providing and interpreting geotechnical information for bidders. The pros and cons of these various methods are discussed and assessed.

Jan 1, 2001

By L. M. Litz

In reply to Mr. DeVries comments on my paper, I would like to say that it is true, as pointed out by Mr. DeVries, that under some special conditions, the use of high concentrations of hydrogen peroxide might provide higher short term in-situ …

Jan 1, 1982

By Kazuya Naito, Nobuyuki Okamoto, Natsumi Kamiya

JOGMEC (Japan Oil, Gas and Metals National Corporation) became the first entity to sign an exploration contract for Cobalt-rich Ferromanganese Crusts (Crusts) with the ISA (the International Seabed Authority). The contract was signed on 27 January 2014, and 15 years exclusive rights for exploration activities had started in the contracted area, located in the North-Western Pacific Ocean. JOGMEC had already conducted basic scientific surveys around the contracted area from 1987 to 2012. Activities by JOGMEC that will be undertaken during the first 5 years of the contract include examination of geological and acoustic surveys, environmental baselines surveys, and undertaking basic studies of R&D in mining, processing, and smelting technologies. Geological surveys will include analysis of rock core samples, using BMS (Benthic Multi-coring System). Deep-towed TV Camera will be used to estimate the distribution of crusts deposit and to get basic environmental data of deep-sea megabenthos. Water sampling, marine sediment sampling, and installation of mooring systems on the seafloor will also be conducted as a part of environmental surveys.

Sep 1, 2014

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

For many years, underground workings in the Bou Azzer mine have been challenged by geotechnical problems related to the serpentinite instability. The stage of evaluation of the compression potential is crucial to develop an appropriate drilling method and the choice of non-standard support. This research work presents a retro-analysis of serpentinite behavior in underground excavations at different depths, using a multi-approach method, based on several empirical and semi-empirical and theoretical-analytical methods, calibrated by the observational method. The analysis performed in this work reveals that underground excavations in Bouazzer East and Ait Hmane area would encounter compression problems that were recognized as the most serious from a depth of 300 m because of the effects of lithology and tectonics. Therefore, the Aghbar region has a slightly negligible compression potential. The compressive failure mechanism in this mine, depending on the mechanical strength, is started at induced stress of 9 MPa.

Nov 27, 2021

"The profile of the respondents was that of a professional responsible for communications, community relations or corporate social responsibility programs. By targeting a consistent professional profile it was possible to ensure that most respondents had a similar degree of responsibility and/or decision-making ability related to the application of communication technologies. The research attempted to be inclusive and attention was paid to interview respondents from both genders and from indigenous groups.4, 5 A codebook of 80 themes was developed that highlighted recurring topics; for example, codes were created to identify risks, benefits, policies and learning process of using social media and included topics that were repeatedly emphasized by respondents (i.e. age, efficiency and language). Both manifest coding (i.e. coding of the visible content, such as specific words) and latent coding (i.e. coding of underlying meanings) was undertaken (Creswell [13]). The codes were used in the qualitative analysis using ATLAS.ti software and network views were created to illustrate the relationship between major themes of this research. There are limitations to this research, largely related to the changing nature of the Internet and communication technologies. There is also a geographic limitation to the application of this research because most of the data was gathered primarily from Canadian sources.6 Different levels of Internet penetration, or limited access to computers or mobile devices, and low literacy rates may reduce the applicability of the research in countries with low Internet penetration. A more systematic process to selecting candidates may have helped bring balance to the final list of interview respondents. For example, most of the corporate respondents were from medium and large companies and there was not adequate representation of small mineral exploration companies. The research did not probe into social media applications by different business groups within the mining sector, such as smelting and processing."

Jan 1, 2011

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

By Drew A. Meyer

Magnetic metals are the granddaddy of products which may be recovered from municipal waste. Aside from hand-picking of newsprint and corrugated boxes, magnetic metals are usually the first items a resource recovery facility considers extracting from the solid waste stream. Magnetic metals from incinerator residues and from municipally mandated source segregation programs were first used in significant quantities by the Copper Industry. The ability of the Copper Industry to consume metals from the municipal solid waste stream raised everyone's hopes that there would be more markets for municipal scrap when more of it became available. Somehow something has gone wrong. It is widely acclaimed that scrap is an environmentally sound and economical source of iron. It is greatly in demand for Its contained energy. The prices that the steel industry has been willing to pay for the scrap during the past year are all the proof anyone should need that scrap Is desirable and sought after. But the very fact that I'm speaking today on the markets for magnetic metals recovered from municipal waste indicates that something Is wrong. Clearly the problem is not that we do not need the scrap. The problem is we have not produced the kind of scrap that consumers are willing to buy - either through ignorance of what the consumers wanted or through a conviction that ferrous scrap is so obviously a good thing somebody will surely want it no matter what. Dr. Harvey Alter of the National Center for Resource Recovery has said "You can't sell garbage". In a sense that is only partly true. It really should be "You can't sell garbage for very long". The Steel Companies, in an effort to prove that steel is an environmentally desirable packaging medium, have bought some scrap that can only be described as garbage. They are to be commended for doing so. The fault lies not with the Steel Company for taking and paying for "garbage" but with the producer of that poorly prepared scrap. Far every instance where the steel industry has purchased the often undesirable product from resource recovery facility there are several magnetic installations sitting Idle because someone forgot the most essential part of producing the magnetic product - selling it to someone.

Jan 1, 1975

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By K. Vatterrodt

Thallium is not significantly removed from mining influenced water (MIW) through conventional treatment in hydroxide precipitation plants. We experimentally investigated modifications to hydroxide precipitation schemes to concurrently remove thallium. Our goal was to determine cost effective and efficient hydroxide precipitation process modifications for thallium removal. Strategies for removal targeted multiple mechanisms including sorption, co-precipitation and/or oxidation of monovalent thallium. Modifications were tested in batch and included oxidant evaluation and the role of manganese. Removal of thallium was enhanced by the addition of permanganate as well as oxygen by aeration. In addition, contact with retained solids and the initial manganese concentration played an important role in the extent of thallium removal observed. This paper reports on our findings and discusses the implications in the removal of thallium with minor modifications to the hydroxide precipitation process.

Feb 27, 2013

By P. Moran

A promising and increasingly popular tailings management strategy is to place cemented tailings underground as backfill. The placement of cemented tailings results in enhanced geotechnical stability and a purportedly more geochemically stable tailings form with lower leaching potential. Conventional subaerial tailings management can negatively affect water quality if weathering causes acid rock drainage and metal leaching (ARD/ML) to occur, whereas cemented tailings can limit leaching via porosity and permeability reductions and contribute alkalinity to limit the potential for ARD/ML. Cemented tailings backfill appears to be better, but how can this advantage be proven? Currently, cemented tailings backfill is utilized at mining operations internationally, but there is limited guidance on performing geochemical characterization and associated evaluation of the potential impacts to water quality. As a result, various approaches to simulating the leaching behavior of cemented backfill have been utilized, including some methods that are unlikely to represent weathering under site-relevant conditions. American Society for Testing and Materials (ASTM) Standard Test Method C1308-08 is a diffusion testing method initially developed to assess constituent release rates from solid nuclear waste forms. ASTM C1308-08 uses intact cylinders that more closely represent actual backfill than methods that require crushing or size reduction. It is widely believed that leaching from actual cemented tailings is controlled by diffusion through small pores that exhibit limited exposed surface area, making diffusion testing particularly applicable to cemented tailings placement.

Feb 27, 2013

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021