Search Documents

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By W. G. Pariseau

"The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to the start of mining in the south barrier pillar. Subsequent loss of ground control in August 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterward three rescue team members. A U.S. Mine Safety and Health Administration (MSHA)report describes the events in detail (MSHA, 2008).An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools and selecting the right tool for the job is essential. In this regard, minimum program requirements include capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses.The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two-dimensional finite element analysis indicated pillar safety was by no means assured (MSHA, 2008; Pariseau, 2008; Pariseau, 2011). Geometry of barrier pillar mining is limited in two dimensions for example, crosscuts are not seen in vertical cross sections. While three-dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three dimensions. This technique involves a dual node - dual mesh concept. Both have been used separately in much earlier work, but are only now used in combination. It is possible to have an estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale (Pariseau, 2014). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2014

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By V. A. Leach, J. R. Johnson

The calculation of the dose to the bronchial epithelium, lungs and other body tissues from exposures to airborne radon and thoron daughters requires a knowledge of the pattern of deposition in the respiratory system and clearance from it. Exposure to radon or thoron daughters is measured in units of Working Level Months (WLM), which is independent of the aerosol particle size, the fraction of daughters that are attached to the aerosol and the degree of disequilibria between the daughters, and age and breathing rate of the subject. These factors will influence the deposition and clearance, and hence dose. It is therefore of interest to find the relationship between WLM and calculated dose as a function of aerosol size, unattached fraction, and disequilibria, and of age and breathing rate, and to define ranges for these parameters for which WLM is an acceptable measure of the risk. This presentation briefly reviews the two dosimetry models being considered by a current Nuclear Energy Agency (OECD) Working Group, and using these models, defines limits on parameters for which the WLM is applicable.

Jan 1, 1981

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By T. Gupta, T. Ghosh

Rare earth elements (REEs) and their compounds are essential in a multitude of mundane and sophisticated applications such as renewable energy technologies, catalysts, medicine, and defense applications. The global supply deficit could be attributed to the destabilization of REE market that has, as a result, incentivized indigenous production of REEs. Cost-effective and environmentally benign opportunities are being explored for the production of REEs from non-conventional mineral sources including coal and coal by-products to stabilize the supply chain. Coal from Healy coal mine and Wishbone Hill deposits in Alaska have been quantified for REEs and were found to possess elevated total REE concentrations as compared to world average levels (60– 70 ppm). The objective of the study was to concentrate the REEs in the froth phase by froth-flotation of the fine size fraction (< 75 μm). A Box-Behnken design of experiment was employed to ascertain the main and interaction effects of operational parameters on response variable by analyzing 3D response surfaces. Experiments were carried out to maximize REE recovery and concentration by modeling and optimization of three operating variables (frother dosage, pulp density (% solids), and collector dosage). Based on the results, the optimum flotation conditions for maximum recovery at an elevated concentration of REEs in the froth fraction was obtained at 4.2% solids and 32.7 ppm of frother dosage for Healy sample and 10% solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic relationship between the input and response variable was found to be independent of collector dosage suggesting good surface hydrophobicity and floatability of the two coal samples.

By A. H. Shapiro

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micron-range particles that form paste-like, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake-flow control structure that allows expressed liquid from the cake in the dry beach region to be returned back to the liquid pool while maintaining high solids throughput. In order to provide optimal performance with various operating parameters (feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids, and different slurry types), the cake-flow control is adjustable. The second part of the beach is preferably at zero angle. Tests showed that the new design allows increases in both solids dryness and solids throughput.

Jan 1, 2001

By James Diekmann

The Disputes Potential Index (DPI) is a computer program designed to help team mem¬bers assess the likelihood of contract disputes on a construction project. The program&apos;s predictions are based on data from 159 construction projects that encompass a variety of public and private projects. The impact of three categories of project characteristics are included in the DPI program, specifically, people, process and project characteristics. Ultimately, DPI returns an overall project score that indicates the likelihood of exces¬sive contract disputes. The output of a DPI analysis can be used as part of a contract readiness review or to define the need for extraordinary dispute avoidance procedures. This paper examines the development of DPI and presents the results of DPI analyses on several tunneling projects.

Jan 1, 1995

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By M. J. Fairweather, J. R. Egan, W. A. Meekel

Cominco Metals, in cooperation with two Canadian Universities and the Government of Canada, is developing applications for column flotation in the treatment of lead and zinc ores. Plant scale results at Polaris and pilot plant studies of Sullivan, Pine Point and Red Dog ores show column flotation to have significant advantages over conventional mechanical flotation for lead and zinc cleaning. Results from these ongoing studies are discussed in relation to ore texture, mineral recovery, impurity behaviour, scale-up and control.

Jan 1, 1988

By Thomas Kuhn, Carsten Ruehlemann, Christina Heller, Anna Wegorzewski

The commercial extraction of metals from manganese nodules on an industrial scale requires more than 50% of the investment necessary to realize manganese nodule mining. This is mainly due to the fact that a completely new metallurgical processing scheme for the extraction of both base metals (Ni, Cu, Co) and high-tech metals (Mo, Li, Ga) has to be developed and upgraded to industrial scale. There are a number of conventional processing technologies that combine hydro- and pyro-metallurgical approaches such as the INCO and CUPRION processes which have been developed in the 1970s and 1980s. Today, new approaches based on selective leaching with chelating agents and bioleaching try to minimize energy consumption and waste production. All of these extraction methods require knowledge how the metals are structurally bound in the manganese oxides. In this contribution we will review the current knowledge about the mineralogy of iron and manganese minerals in the different marine oxide deposits, present our results, and discuss the possible consequences for metal extraction.

Sep 1, 2014

By B. C. Lewis

Have technological advancements in underground coal mining driven people&apos;s skills to new highs or have the expanded skills of mining people driven the industry&apos;s technological advancements. Who knows? What we do know is that both our technology and our people have made meaningful and significant advancements. Overall, longwall systems continue to increase productivity and retreat faster. Globally, gate road development is the primary bottleneck in a longwall mine. The primary bottleneck in gate road development is roofbolting. Generally, roofbolting is the bottleneck in room and pillar operations as well. This paper will present an integrated manufacturer&apos;s (Joy Mining Machinery) vision of the future in comparison to current equipment performance. Particular emphasis will be placed on roofbolter technologies.

Jan 1, 1999

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.