Search Documents

By L. M. Chan, D. H. Carlson, J. H. Johnson

This paper discusses laboratory evaluation of a tailpipe emissions measurement apparatus (EMA) developed by Michigan Technological University (MTU) under contract to the Bureau of Mines. The apparatus dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, C02, NO and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. During the preliminary laboratory evaluation concentrations of DPM, CO and CO2 were measured. The concentrations of CO and CO2 measured by the EMA were usually within ±14 pct of laboratory-measured values for CO and ±20 pct for CO2. EMA DPM concentrations correlated well (r = 0.96) with the laboratory values, but were 29 pct lower on average. The CO and C02 differences were observed to be related to the method of calculating the EMAs' dilution ratio and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminery analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1991

By K. V. K. Prasad

Solution of most engineering problems requires, in addition to vast numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity. However, it is only recently that approaches like the expert systems methodology have been developed to incorporate the judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or "shells" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development of a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.

Jan 1, 1989

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991

By C. L. McKenzie, R. A. Heig

The design and operation of metallurgical laboratories is discussed. Laboratory size, general laboratory equipment and metallurgical staffing are discussed from a standpoint of desired laboratory results.

Jan 1, 1986

By Ron Jackson

The report gives a general method for the geological evaluation of a gold deposit. Recognizable parameters associated with gold mineralization are used to develop a model of an orebody. The California Mother Lode is used as an example.

Jan 1, 1987

By R. J. Pruett, J. Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1999

By J. S. Murty

In this paper, a report is given of studies undertaken in a laboratory rod mill to obtain the optimum conditions for the desired particle size distribution for long-distance transportation of coal through slurry pipelines.

Jan 1, 1987

By Stuart M. Jones, Eugene E. Hively

The Tower Mill is a vertical "stirred" ball/pebble mill recently Introduced In the Western Hemisphere This device offers a significant power savings on wet fine grinding applications when compared to conventional tumbling mills This paper describes the laboratory application of this mill In wet grinding hydrated alumina to products of 50 percent passing 2 to 6 microns

Jan 1, 1983

By R. Parkins

This paper will discuss a method used to refine the fill level, and orifice size for a dual motor conveyor drive with extended delay chamber fluid couplings. The subject conveyor is located on the surface at the Mountain Coal Company West Elk Mine, located near Somerset, co.

Jan 1, 1996

By M. Sengupta, N. I. Johansen, A. K. Sinha

In Arctic surface mines, frozen ground adds to the complexity of slope stability analysis. The seasonal temperature change may thaw permafrost, and this thawed ground is often unstable. A computer program, GEODYNE, was used to simulate the movement of the thaw front in bare and insulated permafrost slopes. The simulation shows that the insulation can be used on mine slopes to prevent thawing.

Jan 1, 1990

By I. Andras

The paper deals with the application of artificial intelligence methods in assessing the effectiveness of longwall shield support. A fuzzy sets based method is used to derive response surfaces/curves representing the dependence between basic parameters of the shield, as the initial setting pressure and the stiffness on the response metric, i.e. the convergence and load increase during a working cycle.

Jan 1, 2008

By Surendra K. Mishra

The principles of dewatering fine coal has been examined in terms of solid- liquid separation. It is noted that the physical and physico-chemical properties of the particle-liquid system influence the rate and degree of moisture removal. Using postulated models the roles of polymers, surfactants and other physical means as dewatering aid are discussed.

Jan 1, 1988

By M. Myers, T. Oxley

Price, lead-time, efficiency, availability, maintainability. These are all the factors involved in the selection of components for a conveyor system in a mining operation. Historically, the decision-makers do not consider all these factors together when it is time to procure the equipment needed to assemble a conveyor system. The Total Cost of Ownership approach enables an operation to attain superior efficiency and desirable maintenance practices, all while minimizing the total cost to operate and maximizing the return on investment.

Jan 1, 2003

By Mary Fu, Helen Leung, Colin R. Phillips

In uranium mines, the median size of the aerosol has been found to be about 0.1 micron or less. Such small aerosols are readily deposited or "plated-out" on dosimeter interior surfaces resulting in the recording of a low dose. The "plate-out" properties of the CEA alpha dosimeter head are described with respect to aerosol properties in controlled experiments in the laboratory. A simple model is derived to estimate the amount of "plate-out" in the CEA head.

Jan 1, 1981

By George Verley

A new and important task in assisting developing countries is the transfer of microcomputer technology applied to mineral exploration and mining. With this objective in mind, three micro- computers have been introduced in Niger and a training program has been put into place. The core of the program consists of two seminars in Niamey, Niger, after which the attendants will be able to operate a microcomputer and use a small library of application software.

Jan 1, 1987

By William E. Souder, R. J. Evans

From time to time, major technological innovations arise that alter the time-honored ways of doing things. Such innovations can dramatically benefit society in terms of new products, increased outputs, reduced costs and general modernizations. However, the advent of these types of technologies is likely to be resisted because of their uncertain potentials, and because they disrupt established routines and industry patterns. This paper reviews the case history of water jet coal cutting, and assesses its potential to become a major innovation within the next decade.

Jan 1, 1983

By Lee Herold Storey

Groundwater remediation is growing in occurrence in the western United States. Groundwater remediation programs are regulated by state water quality statutes. The remedial action plans implemented under these statutes may conflict with well-established existing rights to withdraw groundwater for beneficial use. This paper discusses how the states of Arizona, Colorado and New Mexico administer conflicts between the need to withdraw and remediate groundwater with the existing rights of others to withdraw groundwater for beneficial purposes.

Jan 1, 1991

By Zhang You-di

A comprehensive model has been set up for surface mine long range planning. It is a system simulation model based on the oriented graph theory. Via this model, a series of mining results such as mineral and waste volume, mineral quality, mining intensity, material haulage distances, dumping area parameters and mining coat for different mining alternatives, can be derived and optimized. This model has been applied to 37 mining alternatives in several surface coal mines and proved mathematically correct and results reliable.

Jan 1, 1986

By Deepak Malhotra

Comminution circuits in general account for fifty percent of capital and operating costs for a processing plant. Significant advances have been made in optimization of these circuits. One would expect a few circuits to be the favored designs for plants. Review of grinding circuits worldwide indicates that a variety of circuit designs are utilized for non-technical reasons. A brief review of circuits and reasons for their selection is given in this paper.

Jan 1, 1998

By Peter D. Warwick

Recent investigations conducted by Federal, State, and industry organizations suggest that significant coalbed gas resources may exist in the Cretaceous and Paleocene-Eocene coal beds of the Gulf of Mexico Coastal Plain. Exploration efforts have focused on three areas which are in south Texas, north-central Louisiana, and south-central Mississippi (Figure 1). Coal-bed gas production is currently underway in south Texas and in north-central Louisiana. In Mississippi, several test wells have been drilled but no data are available on their production potential.

Jan 1, 2005