Search Documents

By Vas Choudhry, Randhir Sehgal

Conventional clean coal technologies which consist of coarse coal cleaning by gravity methods and treatment of natural fines by flotation can only remove a portion of the pyritic sulfur and ash in the coal. Higher (+90%) pyritic sulfur rejection is attainable when coals are ground to ultrafine sizes to enhance liberation of the mineral matter and then cleaned. However, cleaning of coal at very fine sizes poses a number of unsolved problems, the chief one being the loss of cleaning efficiency. This, of course, means that liberation of pyrites does not always equal its rejection. In addition, the dewatering of fine- cleaned coal, and its handling, transportation, and acceptability to the utility industry a1 so pose considerable technical and economic problems, especially when compared to the FGD alternative. This paper addresses some of the critical issues involved in the cleaning of ultrafine coal s.

Jan 1, 1989

By R. G. Reddy

Iron solubility's in spent pickling (HFHNO3 -H2O) solutions were determined as a function of HF and HNO3 acid concentrations. A chemical analysis of the industrial pickling solutions and sludges was performed. The stable phases observed in the sludges are FeF3.3H2O and (FeCr)F3.3H20. Pure Fe metal, AISI 316 stainless steel and AISI 416 stainless steel were used in this study. The results show, that the solubility of Fe increased as the concentrations of HF increased in the pickling solution at a fixed concentration of HNO3. A reasonable agreement between the experimental solubility data and the theoretical calculated data was obtained. X-ray diffraction analysis showed that the solid solubility product formed in the ternary solution containing pure Fe is mainly, at a high pH value, FeO(OH) compounds and, at a low pH value, Fe F3.3H2O compounds.

Jan 1, 1994

By D. Armour, E. R. Bauer, D. R. Zuchelli, T. M. Durr, E. R. Reeves

A team of noise specialists from the National Institute for Occupational Safety and Health (NIOSH), Mine Safety and Health Administration (MSHA), and Joy Manufacturing attempted to evaluate an engineering noise control on a Joy longwall stageloader. The team developed and executed a test plan to evaluate the noise attenuation of the engineering control in an underground coal-mining environment. An evaluation of the long-term noise effects and durability of the engineering control were also a focus of the research effort. Pre- and postcontrol measurements consisting of a combination of worker dosimetry and task observations, tape recordings, and sound level measurements were used to evaluate the engineering control. A description of the engineering noise control, pre- and post-control sound level measurements, and an evaluation of control success is presented. In the end, no evaluation was possible due to mining practices, miner task variations, and inconclusive data.

Jan 1, 2005

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

By G. Atesok, M. S. Celik, G. Onal, I. Yildirim

A new coarse cleaning device, the Stripa, has been developed for processing of coal in the size range of -100+10 mm. The Stripa is an auotogenous heavy medium separator originally developed for processing of iron ores. Although it has been employed in concentrating ores such as chromite, it has not been applied in coal cleaning. In this study, a pilot plant scale modified Stripa and its counterpart alternative, a diaphragm jig, are compared using subbituminous and lignitic coals. The separation performance of the Stripa and the diaphragm jig has been established in the light of washability properties of the coal samples. Comparison of the performance of the Stripa with that of the jig indicates that the Stripa can be used in coal preparation circuits as an alternative to jigs in the size range of -100+10 mm. Simplicity, low initial investment, and low operating and maintenance costs make the Stripa a plausible candidate for coarse coal cleaning. More importantly, Stripa due to its short residence time, has a superior capacity over jig.

Jan 1, 1995

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By R. Bhaskar, H. Xie

Fractal theory was horn in the mid-1970s. Since then, its application has been spreading day by day, from mathematics and geology to areas such as geophysics, physics and material sciences. In this paper, fractal models are developed to characterize particle size distribution and surface area. Theoretical formulas are derived for the computation of fractal dimensions D (size) and D[s] (surface area). The models developed are applied using experimental data of particle size distribution and surface area obtained from the Microtrac Particle Size Analyzer for dust processed by several size reduction devices. The theoretical models and the experimental data are found in good agreement. The fractal dimensions obtained are D = 1.350 to 1.770 and D[s] = 2.058 to 2.584 for fine coal dust particles (< 15 µm) produced by various size reduction mechanisms. The physical meaning of these fractal dimensions is also related to the dust generation processes.

Jan 1, 1994

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By Charles D. Litton, Margaret R. Egan

In order to reduce the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Welding and cutting with arc or flame can also produce combustion products capable of triggering nuisance alarms. In this report, the response of the DDD to the emissions from diesel exhaust, arc welding, and flame cutting are compared to the response of conventional smoke and carbon monoxide (CO) detectors. The data show that when the DDD is set at an alarm threshold of 0.05 v, it will reliably detect a developing conveyor belt fire while remaining insensitive to other sources of nuisance combustion products. The alarm times of the three types of detectors were also compared. The DDD alarmed first in response to a smoldering conveyor belt in two of four experiments.

Jan 1, 1992

By Ing Newton Amegbey, Joseph Afari Idun

Ashanti Goldfields Corporation (Gh) Ltd., the leading gold mining operation in Ghana is embarking on a major rehabilitation and expansion programme to increase gold production. A new southern ventilation district was targeted for this programme, and the ventilation system was to be reviewed in order to cope with increased production. The southern ventilation district was previously ventilated by booster fans. This arrangement was however, inadequate to solve the problem of the need to reduce smoke clearance time of the production areas, and to generally improve the underground ventilation conditions. Fan maintenance costs increased with the number of fans installed in the booster fan arrangement, and the fact that the fans were installed underground made maintenance difficult and took longer time. It became necessary to consider the installation of a new main fan on the surface. This paper gives an overview of the ventilation systems of the southern ventilation district of the mine before and after the new main fan was installed. The field tests carried out on the fan to ensure that it complied with supplier&apos;s specifications are described, and the new system analysed to see it&apos;s effectiveness.

Jan 1, 1993

By S. J. R. Lowrie, J. S. Edwards, A. D. Jones

A small scale model has been constructed to simulate air and gas flows on a full scale retreat longwall coal face. Scaling relationships were derived to define how the main aerodynamic properties of the full scale could be preserved in the small scale model. These scaling requirements include: a minimum value for the Reynolds number for the flow on the face in order to maintain turbulent flow with a constant non-dimensionalised coefficient of turbulent dispersion; a constant Richardson number to maintain similitude for the formation of layers of buoyant gas; scaling of the permeability of the waste so as to obtain the same proportion of seepage flow through the waste; pressure gradients due to the ventilation and to the density difference (between the air and the gas layer) were kept in proportion; and in the waste, the relative contributions of inertial dispersion and molecular diffusion were approximately in proportion. The complementary roles of computational fluid dynamics (CFD) and aerodynamic scale models for simulating mine ventilation are discussed. The physical model is described and an example presented of simulations of the effect of changes in mining condition on the effectiveness of gas control in retreat longwall coal faces.

Jan 1, 1995

By R. L. Garrett

The quality of mineral additives used in a drilling fluid (mud) can dramatically affect the fluid&apos;s properties and the overall cost of drilling an oil or gas well. The principally wed minerals are bentonite, barite, barite/hematite blends, and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity and gel strength and to provide a low permeability filter cake. A multimillion dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason oil companies using these materials sometimes set their own quality standards beyond those already specified in APZ Spec. 13A. Also discussed in this paper are the current standardization activities of API Committee 13 on these minerals.

Jan 1, 1988

By R. V. Ramani, S. Tan

In this paper, several commonly used computer truck-dispatching criteria are evaluated. A computer-oriented truck-dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. However, several dispatching criteria that have good potential to increase performance can be identified. All basic dispatching criteria, including minimizing truck waiting time, waiting shovel with minimum waiting time, minimizing truck saturation, maximizing truck momentary productivity or optimization of truck routes, provide local optimal solutions. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. It may be necessary to search for a hybrid combination of the several truck dispatching criteria that have good potential for a given situation. An approach to selecting such a hybrid dispatching criterion is presented.

Jan 1, 1993

By Zbigniew Pokryszka, Eric Saraux, Christian Tauziède, André Carrau

This paper presents recent developments in the use of a CFD model for representing the flow of gases in the goaf of retreat faces. In France, it is of highest importance to optimize firedamp drainage in very gassy mines and nitrogen injection in faces prone to spontaneous combustion. Numerical modeling has been used to solve this problem. So the model developed has been first calibrated using a large quantity of field data and could then be used for various simulations. Though still in progress, this research has given promising results, many of them being already set into practice.

Jan 1, 1997

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau&apos;s experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By J. Pflieger

The International Iron and Steel Institute (IISI - http://www.worldsteel.org) has initiated the development of a comprehensive freely-available, internet-delivered package of highly interactive e-learning resources for undergraduate students and steel industry employees. The resulting e-learning environment (http://www.steeluniversity.org) creates a ?one-stop? shop covering all aspects of steelmaking, steel products and applications, the underlying scientific and engineering principles, industrial and academic collaboration, as well as environmental and sustainability issues relevant to the steel industry. The module entitled ?Sustainability, Steel and the Environment? of the steeluniversity.org provides interactive e-learning resources on the following topics - Sustainability. - Principles of Life Cycle Thinking. - Environmental Life Cycle Assessment. - Application of Life Cycle Assessment. The aim of this particular module is to enable the learner to identify relevant environmental parameters over the life cycle of steel products as well as to learn about the resulting environmental effects and impacts. Furthermore he/she will be enabled to explain the basic idea of Life Cycle Thinking and Life Cycle Assessment (LCA) in terms of Goal and Scope definition, System Modelling, Life Cycle Inventory (LCI), Life Cycle Impact Assessment (LCIA) and Interpretation. In addition, the learner can explore selected LCA scenarios facing the steel industry and its customers in the automotive and construction sectors.

Jan 1, 2007

By K. L. Branham, D. W. Steeples

Surface collapse over abandoned sub- surface coal mines continues to be a problem in many parts of the world. High-resolution P-wave reflection seismology was successfully used to locate water-filled cavities in a 1-m (3-ft) thick coal seam at depths of 9 m (29 ft) in southeastern Kansas. A dominant frequency of 275 Hz was attained enabling us to delineate the top of the coal seam. To our knowledge, this study is one of the first to locate water-filled coal mine cavities at depths of less than 30 m (100 ft) wing high-resolution P-wave seismic reflection techniques.

Jan 1, 1987

By John G. Watson, Judith C. Chow, Richard T. Egami, Daniel L. Freeman

A methodology for apportioning ambient PM-10 (particulate matter) concentrations to sources is described and applied to PM-10 concentrations in the vicinity of a large gold mining operation. With this methodology, samples representative of particulate sources such as desert overburden, diesel equipment, milling operations, road surfaces, and others are collected and analyzed to derive chemical source profiles. Ambient 6-hour PM-10 samples collected downwind from the mine are analyzed and used with the Chemical Mass Balance model to apportion ambient PM-10 among the various sources. In an example application, primary contributing source types are found to be desert overburden and diesel equipment. Relative contributions vary according to time of day, with diesel equipment frequently being the dominant contributor during nighttime periods.

Jan 1, 1991

By S. Hardcastle

Kidd Creek mine has recently completed upgrades of its primary ventilation systems enabling it to maintain a delivery of 1200 m3/s to continue mining ore zones extending to over 3000 m below surface. Following these upgrades the mine initiated a multi-stage review of their ventilation usage. The focus of these reviews, ranged from a brainstorming session of invited experts, through an evaluation of production plans to a detailed analysis of production data to determine if the ventilation system could be run more efficiently, thereby reducing the mine?s power consumption and associated operating costs. The initial review identified 1500 kW of installed fan power that could be eliminated from the primary ventilation system. The benefits of the subsequent analyses, so far, are not as measurable. The second and third analyses, respectively using long range production plan data and historic production data to determine ventilation requirements based upon diesel equipment, did not agree. Both were shown to have limitations, the future based analysis underestimating, and the historical analysis overestimating the requirements. Regardless of the failings of each method, important outcomes were achieved from the detailed analyses, namely, the ability for a mine to meet a forward analysis prediction of airflow depends on its ability to adjust the ventilation to meet the dynamic nature of the mining process. Also, to minimize total ventilation requirements, a mine must regularly redistribute its airflow; this not only reduces the total volume requirement but also increases the variability of the delivered flows which can provide further operational savings. Since the detailed analyses, the Kidd Creek mine has implemented a more frequent ventilation review and redistribution procedure; consequently, it now operates with an average delivery of 930 m3/s, which is 23% lower than in 2005 at the start of the review process.

Jan 1, 2009

By P. Bevilacqua, G. Ferrara, U. Preti

In the last decade, Meloy developed the IAC - Interfacial Area Conservation - model of liberation. His work included three conservation laws and a mathematical tool called textural transform. This paper reviews the developments and applications of the IAC model. From simple spherical two-phase locked particles with planar interfaces, the model has been developed for curved interfaces and solids with complex textures. Moreover, complex shaped particles and ores having more than two phases have been considered. The model equations give the degree of liberation of the component phases for different ore textures – platy blocky and acicular - as well as for different sue distributions. Lockedness profiles are offered for defining the middlings composition, so that from the model it is possible to predict washability curves.

Jan 1, 1992