Search Documents

By Qingxia Liu, Chen Tingzhong, Chen Jin, Yang Xiaosheng

It is common problem (Huan Xinsheng, etc.,l992)for most iron ore concentrators in China that the concentration of thickened tailings is lower than the need for economical transportation. To solve the problem, two methods of improving the properties of the existing thickeners and using separate thickening technique have been applied in three iron ore concentrators. However, in the case of the Daye iron concentrator a new technique of cyclone-flocculated sedimentation was developed by present authors and verified by experiments. The new technique employs efficient hydrocydone designed by authors in conjunction with a low cost flocculant named KLP.

Jan 1, 1995

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By J. J. Kellar, W. M. Cross, J. D. Miller

Infrared spectroscopy has been one of the most useful experimental techniques for the analysis of surface reactions in flotation systems, including surface alteration and surfactant adsorption reactions. With the advent of Fourier transform infrared (FTIR) spectrometers, many low-energy throughput IR experimental techniques previously unused by flotation researchers have come into greater use. In particular, internal reflection spectroscopy (IRS) is the most often used technique for in-situ studies. To date, three IRS methods have been used for in-situ measurements. These techniques are evaluated for use in characterization of surface reactions in flotation systems. The method using mineral crystals as reactive internal reflection elements (IRE) is of particular interest because it allows surfactant adsorption densities to be calculated directly from in-situ spectral data in real time. Application of in-situ FTIR/IRS with reactive internal reflection elements will be demonstrated for collector adsorption reactions in each of the major flotation systems. The alumina (A1203)/sodium dodecylsulfate system is used as an example for insoluble oxide/silicate flotation, while the fluorite (CaF2)/oleate system serves as a paradigm for semisoluble salt flotation. For sulfide flotation, sphalerite (ZnS) is used as the reactive IRE with potassium amylxanthate and potassium ethylxanthate as collectors. In the case of soluble salt flotation, sylvite (KC1) is used as the IRE with n-octylamine as collector. Finally, the use of reactive IREs in the near-IR spectral region and in spectroelectrochemical research is discussed.

Jan 1, 1989

By Neal I. Rosenberg

There is an old education maxim that a good teacher "first tells 'em what he's gonna tell 'em, then he tells 'em, and finally he tells 'em what he told 'em. I'm sure this says something about me as a teacher, and therefore as a student as well, but I'm going to begin by violating that maxim. The first thing I'm going to do is tell you what I'm not going to tell you. I'm not going to tell you that my company has found the solution to frozen coal problems. I'm not going to tell you that there is a miraculous new formula, and your frozen coal worries are over. Actually, it is really questionable whether there is a single step or process which will provide the answer. On the other hand, I do believe that at Union Electric we have made significant improvements in our ability to deal with frozen coal over the last couple of years, and I propose to describe some of the things we have done, what conclusions we have drawn so far, and the direction in which we are now headed. It would be well here to give a brief picture of the Union Electric system and the frozen coal problems we face. Union Electric is an investor owned electric utility with headquarters in St. Louis, Mo. Total generating capability is on the order of 6800 megawatts, which snakes us 24th or 25th largest in the United States. Power generation is by steam (both coal and oil fired), hydro, pumped hydro, and combustion turbine units. Although that is a diverse power supply, by far the largest source is our four coal fired steam plants. One receives coal exclusively by barge, the other three by rail. It is at these last three plants that the frozen coal difficulties arise.

Jan 1, 1980

By Gordon D. House, J. B. P. Sawyer

The Bannockburn gold prospect is a new discovery in Ontario's oldest gold camp at Eldorado, eastern Ontario. Mono Gold Mines Inc. of Vancouver, British Columbia, acquired the property in 1980 and in 1984 discovered a previously unreported gold bearing quartz vein system to the northeast of the old Bannockburn Mine. Extensive diamond drilling carried out since 1985 defined a quartz vein system over 475 m (1 ,500 ft) of strike to a depth of over 105 m (350 ft). Limited underground exploration by decline to the 22.9 m (75 ft) level in 1988 confirmed the continuity and tenor of the quartz veins. Gold occurs as native metal with minor sulphides and bismuth tellurides in a quartz carbonate vein system within metasedimentary and metavolcanic rocks of the Grenville Province. Metallurgical test work on a surface bulk sample was favourable. Estimates of drill indicated reserves have been made as well as reserves based on the limited underground exploration.

Jan 1, 1989

By M. C. Roberts

The material composition of product is defined as the quantity of metal used per unit of product manufactured during a year. The material composition of product has shown steady and persistent declines over time for most metals and materials. This tendency demonstrates the continued improvements in manufacturing technology resulting from substitutions of other materials and increases in production efficiency. The purpose of this paper is to use the material composition of product to show the impact of advanced materials on the use of traditional metals.

Jan 1, 1992

By E. A. Rychkun

With the aid of modern computer automation, certain mathematical techniques are easily adapted to geophysical, geochemical and geological data analysis. First and second derivative filtering (or transformation) of raw data, in many cases, gives a better indication of anomalous conditions than conventional methods of analysis. The calculations involved, which are tedious manually, are simple, accurate and fast with the assistance of Fourier analysis and modern computers.

Jan 1, 1968

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 m (8 ft) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting. Saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can prevent solution flow through large portions of the stockpile. This implies that care must be taken to ensure that ripping is carried out to a depth of at least 2.4 m (8 ft) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2002

By P. Zhang

The Crago “Double Float” process is widely used in upgrading phosphate ore. This process is inefficient, as it floats about 30-40% of the sands in the flotation feed twice and requires a deoiling step. This paper summarizes several research projects on improving phosphate flotation. The University of Utah investigated a new flotation chemistry for efficient flotation of phosphate in a single step. The Florida Institute of Phosphate Research developed several single-collector, all-anionic flotation flowsheets using various sizing schemes. In addition, Eriez invented the HydroFloat separator, which demonstrated great potential for processing coarse flotation feed in one step.

Jan 1, 2004

By G. Banini

A plug-flow model is described for the reactor mass balance of a typical AARL gold elution process. The model is in the form of a hyperbolic differential equation and was transformed using the method of characteristics. The transformed model was then solved simultaneously with models dependent on intraparticle surface diffusion and film transfer parameters. The solution was found to represent the experimental data for a modified form of the AARL elution. Correlation between the experimental conditions and the film transfer parameters estimated by the model are also presented.

Jan 1, 1998

By I. J. Jansen, C. L. Hooks

Successful soil construction involves prepa¬ration of an adequate base, selection of high quality soil ma¬terials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experi¬ments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construc¬tion. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By N. N. Clark, C. M. Atkinson

Pachuca tanks are used widely in the mineral industry for leaching and mixing operations. An analysis has been presented previously to predict circulation of homogenous slurry in Pachuca tanks with full height draft tubes. However, settling of solids causes deviation from the homogenous case. Circulation of settling slurry in a Pachuca tank is modeled and shown to be a function of settling velocity, solids fraction, solid and liquid density, air flew rate, and tank dimensions. The pressure balance is shown to be very sensitive to these parameters, especially at low slurry velocities. Equations for predicting the air requirements in Pachuca tanks containing settling solids are presented.

Jan 1, 1988

By K. A. Grace, D. E. Ranta

The application of geology does not cease with the discovery and delineation of a mineral resource, but continues in the calculation of the economic parameters that determine reserves. Reserve determination, reduced to essentials, is the determination of the cost of production of a mineral commodity from a resource. This cost comprises mining, processing, waste disposal, reclamation and marketing costs. Geological input is vital in the calculation of the individual cost parameters from mining to reclamation, and even has same impact on marketing. Geology thus has a critical role in the determination of reserves.

Jan 1, 1992

By K. N. Han, P. B. Queneau, Bruce W. Cavender

Measures of metallurgical performance, such as recovery rates or mass balances, are frequently based on point estimates of operating conditions in the system of interest. Because the processes being measured are dynamic, a range of uncertainty accompanies each measurement; this uncertainty is reflected in the accuracy with which the calculated result describes the true metallurgical performance. In stochastic modeling, a range of probable values is used in place of a point estimate to describe each variable. The calculated result takes the form of a distribution, delineating both the magnitude and probability of potential outcomes.

Jan 1, 1993

This paper discusses how the link between design software tools and recycling models can be established in order to predict the recyclability of the car during the design phase, as well as to be able to apply design for recycling on a solid technological basis. Due to the complexity of the design of the car, optimisation of recycling can only be realised based on a sound technological basis, in which the dynamic and statistically distributed parameters affecting the recycling rate are described and understood. This paper gives a brief overview of the dynamic and recycling models, which are developed for optimisation of the recycling of the car and the calculation of recycling rates of the car in the design phase in view of EU legislation. Moreover the possibilities for modelling of shredding and liberation within the recycling system are discussed. The performance of experiments on a fundamental basis in order to collect statistically correct industrial data, supported by a closing mass balance, is referred to on the basis of a large scale industrial recycling experiment. It will be shown how design for recycling and environment can be supported by the sophisticated models as developed by the authors.

Jan 1, 2005

By K. A. Natarajan, P. Somasundaran, Namita Deo

Biological processes have recently become more attractive in hydrometallurgy and mineral processing due to their lower operating costs, potential for processing low-quality ores and flexibility. Adhesion of microbes and their metabolic products can modify the particles to render them hydrophobic or hydrophilic. Such modifications of the surface properties are used in flotation and flocculation of minerals. Microbes are also able to dissolve different precious metals from their ores. In this paper, the role of microbes and their metabolic products as surface modifying reagents in extraction processes is discussed. In addition, the ability of certain microbes to adsorb toxic metal ions or to degrade toxic chemicals discharged by industries is examined.

Jan 1, 2000

By J. Mastoris

The determination of the surface area that may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted. Furthermore, the influence of both mining and geological factors (i.e., mining width, depth and overburden lithology) on this angle is examined using the Surface Deformation Prediction System (SDPS) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1995

By R. J. Pruett, P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber and caulks and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness and outstanding rheology in water systems. The quality of calcitic GCC ores, which includes chalk, limestone and marble, is dependent on calcite purity and the nature and quantity of the impurity minerals. Wet and dry grinding are used in the processing of GCC. Ore processed by optical sorting, flotation and/or particle-size classification has higher brightness and lower abrasion characteristics. GCC markets are a function of the product's properties, purity and cost.

Jan 1, 1997

By H. Pieterse, K. S. Fraser, J. R. Goode

The Goldstrike autoclave plant is designed for the pressure oxidation of 1363 t/d (1500 stpd) of refractory gold ore. The plant was commissioned in early February 1990 over a one week period - an unusually short period for a plant of this complexity. The rapid plant start-up is attributed to certain detailed design and control aspects of the plant. This paper discusses key features of the autoclave plant with emphasis on the design of the splash/flash system of heat recovery and the control systems. Commissioning and plant operations over the first three months are reviewed.

Jan 1, 1990

By M. W. Chanda

This paper presents the development of a rock-creep measuring apparatus using air as the initial pressure source. Servo-controlled machines can and have been used for time-dependent property tests. However, the long-term nature of some tests makes essential the complete independence of stress-maintaining equipment from main power sources or continuously running hydraulic pumps. The main objective of this paper is the development of a creep testing machine that is free from interference arising through power supply interruptions or mechanical maintenance normally associated with many compression testing machines. To achieve this, a compressed-air power source was used to drive a compression ram. A few trial results obtained and analyzed using the transient creep law are in reasonable agreement with the general creep law.

Jan 1, 1993