Search Documents

By George P. Demopoulos, Vladimiros G. Papangelakis, Dimitrios Filippou, A. J. Monhemius, G. W. Warren, E. Peters

A new method developed for the estimation of the activity of Ht in mixed sulfate solutions is described and examples of application of this method to the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3 from 298 to 473 K are offered. The method makes use of an "extended Debye-Hiickel" type of equation that was originally put forth by Das for pure H2SO4 solutions at ambient temperature. The treatment of mixed sulfate solutions was made possible by combining that equation of Das with a speciation algorithm which calculates the abundance of all species formed. The developed method, which also takes into account ionic strength and temperature effects, was used to generate hydrogen ion activity and speciation data for all possible acid/metal sulfate pairs of the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3. Finally, under the light of the reported data, specific examples of hydrometallurgical reaction systems are analyzed in terms of thermodynamics or kinetics. In particular, the systems discussed are: hydrometallurgical precipitation of hematite, solvent extraction of Fe(III), acid leaching of zinc ferrite, and oxidation of Fe(II) to Fe(III) by O2(aq).

Jan 1, 1993

By S. Chander

The advantages and disadvantages of various techniques available for controlling reagents in the mineral flotation systems are discussed. Special interest is placed on potentiometric and voltammetric sensors for monitoring flotation pulps. Different approaches to increase the sensitivity of detection and to facilitate in-stream monitoring of solution species are also discussed. The potentiometric sensors are simple to use but are limited by the availability of an electrode reversible to the species to be monitored. In some cases the response signal could be unreliable due to the presence of interfering species. In comparison, voltammetric sensors require a higher degree of instrumentation which, however, provides an opportunity to decrease interferences and increase levels of detection.

Jan 1, 1993

By J. M. Kruger

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially-intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom-shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1997

By J. Bigu

Use has been made of several theoretical models to predict radiation levels in underground uranium mines. The models used are the Evans model, the Thomas-Epps mine model, the isolated mine model, the mine tunnel with no air flow and the mine tunnel with air flow (Beckman and Holub). Calculations based on the above models have been extended to include thoron gas and its progeny, a common occurrence in some Canadian uranium mines. Theoretical predictions include radon and thoron progenies WLs and concentrations, and some ratios of great practical interest. The main differences between the models are pointed out and comparison is made with experimental data gathered during the last three years in several Canadian underground uranium mines.

Jan 1, 1981

By D. M. Muir, C. Cao

Many gold ores have copper mineralisation which presents problems in a carbon-in-pulp operation. Various types of copper-gold ores and ways of tackling the problem are discussed. In some cases copper and gold can be upgraded to a concentrate by flotation; otherwise, copper or gold can be selectively leached. When both copper and gold cyanide are present in solution, it is possible to minimise copper loading onto carbon or to selectively strip the copper from the carbon. Alternative leach solutions like thiourea and bromine are discussed and results obtained with the ammonia/cyanide system are presented in the light of our present understanding of the chemistry involved.

Jan 1, 1989

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By L. Darkwah

The use of explosives in coal mining inevitably results in oversize, midsize and undersize (fines) products due to fragmentation. The oversize can be broken into smaller sizes by further processing. However, the undersize have a negative affect on the efficiency of a mining operation. Therefore, limiting the amount of fines can be economically crucial. This paper concerns investigations aimed at reducing fines generation in coal mining. Inherent fractures were identified as one of sources of fines generation. This paper is centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs, which are evaluated in terms of the fines generated.

Jan 1, 1998

By Peter Sullivan, Johan van Heerden

Increased use of continuous miners and roadheaders in the underground coal mining industry in South Africa has led to improved productivity and efficiency of operations. Of major concern, however, is the increased amount of airborne dust generated during mining. Dust is a health hazard in terms of respiratory diseases, can impede productivity and is the major contributor to the potential of underground explosions. The concern of the South African coal mining industry with regard to the underground dust problem has led to the establishment of a Dust Control Section in the Coal Mining Division of COMRO. In the field of dust suppression system evaluation and design, collaborative work has been undertaken by COMRO and FLOSEP. This paper gives a review of the application of Computational Fluid Dynamics (CFD) in evaluating and improving environmental conditions in continuous miner and roadheader sections. A brief history of the development of the CFD model as well as a discussion of a typical application is included.

Jan 1, 1993

By H. Wu, V. Izaxon

Intensive ventilation is required during the excavation of a mine opening and the subsequent exploitation of the mineral resources. The exchange of heat between the ventilation air and the rock mass has a major influence on the thermal regime of a mine, especially in the initial segment of the airway. In frozen ground, heat flow into the rock mass from the ventilation air can result in the eventual thawing of the permafrost, which can result in roof-rock instability. This paper presents a mathematical analysis of the dispersion process of ventilation-induced heat by thermosyphons placed on the surface of the mine. The principal uses of thermosyphons in the Arctic are to reduce the ground temperature to prevent potentially unstable permafrost from thawing and to increase the bearing strength of the material. The mathematical model of the physical problem, generally known as "the Stephan problem," takes into account the varying thermo-physical properties of air and the frozen and thawed rock mass, the thermal properties of the freeing fluid in the thermosyphons and the phase change of water. Finite-difference techniques were employed to determine the temperature isotherms around the thermosyphons. It was found that two rows of thermosyphons on a 10- x 10-m grid provide an acceptable design spacing for reducing the ground temperature around the mine airway.

Jan 1, 1997

By D. Wallace Fields

Increasing public pressure and demands from various tiers of government have generated a legislative maze of statutory and administrative requirements facing industries involved in mineral extraction and processing. Each tier, of government has asserted concurrent jurisdiction and threats of harsh measures if industry does not satisfy all requirements. In the field of water pollution control, federal requirements have increased, carrying with them increasing techniques of enforcement - ranging from injunctions through criminal penalties. Federal laws have required that states formulate water quality standards as an adjunct to federal regulation. Florida has reacted with the Water Pollution Control Act of 1967. This act incorporates state water quality standards and permit requirements for any installation constituting a potential source of pollution, and provides for civil sanctions as well as injunctive relief. The federal government has utilized an 1899 law to require a permit for discharges into navigable waterbodies - a term which has been judicially defined to include any watercourse capable, after reasonable improvement, for use in the transportation of waterborne traffic. Failure to secure these permits can result in the issuance of an injunction or civil or criminal penalties. The Corps of Engineers will not issue these permits without the approval of the discharge by state, local and other federal agencies. Air pollution similarly is regulated by a multi-tiered network of laws and administrative standards. Federal regulation has increased from early research support in the 1950's through the development of Air Quality Standards and their enforcement by large fines, injunctions, administrative conferences and public hearings. Florida regulation, under the Florida Air Pollution Control Act of 1967, parallels federal law but grants concurrent regulations, requirements and enforcement tools to local and state agencies. Although previous state regulation was minimal, consisting only of three acts passed in 189 1, 1899, and 1911, in the future the mining industry will have to contend with this increasing network of ecological requirements. It is recommended that the industry take the initiative by involving Florida in the Interstate Mining Compact, as well as seeking the passage of a state reclamation law funded by a severance tax.

Jan 1, 1972

By K. Hanumantha Rao, P. K. Sharma

A pure strain of Paenibacillus polymyxa and mineral- adapted strains are used to bring about surface chemical changes on pyrite and chalcopyrite and, thus, theirflotation. Paenibacillus polymyxa was adapted by repeated subculturing in the presence of pyrite and chalcopyrite. The surface chemical changes of bacteria due to adaptation and of minerals after their interaction with bacterial cultures are evaluated by electrokinetic and infrared spectroscopy and are discussed with reference to their flotation responses. Interaction of bacterial cells, bacterial metabolites and whole bacterial cultures affected the Hallirnondflotation behavior of the sulfide minerals. The Xanthate flotation results show that pyrite, but not chalcopyrite, is depressed when the tests are carried out after interaction with chalcopyrite-adapted Paenibacillus polymyxa. This investigation demonstrated that the surface chemical properties of bacteria can be manipulated successfully to achieve the desired effects in the flotation process.

Jan 1, 2000

By F. H. Deily

The petroleum industry has developed and utilized many aspects of rock mechanics, both in its search for petroleum and in its drilling and production operations. Geological exploration activities have been improved by knowledge of earth tectonic forces. Better understanding of seismic wave motion has contributed to a more accurate interpretation of geophysical data. Drilling activities have benefited from basic knowledge of rock strength behavior under in situ conditions. Production has been significantly increased through stimulation techniques, such as hydraulic fracturing. The ability of rock mechanics work to contribute to future petroleum activities will depend upon the development of knowledge of rock properties under greater depths and at higher pressures and temperatures.

Jan 1, 1969

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

By J. R. Parry

Over the past several years, computerized financial models have been an important part of Newmont's strategic planning process. Two applications will be discussed in this paper: a general purpose financial model of Newmont, and a detailed operational/financial model of Magma Copper Company. Newmont?s general purpose financial model was developed using Lotus 1-2-3. It was designed to aid management in assessing the financial consequences of investment and financing decisions associated with long-term strategic planning by simulating the consolidated effect from individual transactions. Not only is the model capable of assessing the sensitivity of specific decisions to changes in the external economic environment (i. e., commodity prices, interest rates, inflation and exchange rates), it can also evaluate the effect from operating and financial decisions, including changing production levels and cost structures at individual operating units as well as simulating several types of transactions, including equity and debt issues, acquisitions and divestitures. The analysis of Magma Copper Company required the development of a detailed operating and financial model of the Company. The model was developed using IFPS in the corporation?s UNISYS (then Burroughs) B7900 mainframe computer and included separate pro forma financial statements for each of San Manuel-Pinto Valley's mines and concentrators, as well as Magma's smelting and refining operations. The outcome of this analysis was the decision to merge Magma Copper and Pinto Valley Copper Corporation, and to recapitalize the new corporation in order to provide funds for a retrofit and expansion of its Arizona smelter and expansions of its refinery and SXEW facilities.

Jan 1, 1989

By Herbert Pöllmann

The mineralogical and chemical compositions of various waste materials undergo different reactions when treated thermally The heavy metal contents can be bound to stable phases. These minerals are called reservoir minerals. The main property of these minerals is the stability in their geochemical surrounding containing the heavy metal cations and anions. Examples for these minerals are apatites, spinels, garnets, perovskites and also water containing minerals like ettringites, metal-metal-hydroxi salts, jarosites and zeolites. When the chemical compositions of different wastes are mixed according to the compositions of the new formed minerals, a probable reuse of these wastes can be obtained. The use of waste incineration ashes for the production of cementitious binders and the use of flue gas desulfurization products for cement additives are shown. Also the transformation of highly contaminated materials into stable reservoir mineral assemblages are shown including the study of stabilization and immobilization techniques.

Jan 1, 1998

By Jim Merza

The recent heightening of environmental issues has forced more and more mining operations to focus on developing new methods to control dust problems encountered at their concentrate dryers, stock piles, tailings ponds and during the loading, transportation and unloading of their products. The development of dust control agents requires a quick reliable and most of all accurate method to evaluate the performance and to optimize the formulation of these products in the laboratory, thus avoiding expensive field trial evaluations. This paper gives an overview of the industry requirements for specialty dust control agents, application techniques and current laboratory evaluation procedures. The paper will also outline the development of a unique dust suppression testing apparatus called the "Dust Box, which is used to evaluate chemical dust suppressants at the laboratory level. Laboratory results from two test programs on different substrates are presented in the paper.

Jan 1, 1994

By L. Yuan, J. H. Rowland III

"In 1995 and 2003, the Mine Safety Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) being used in underground coal mines in the United States. The survey reports showed data for the different AMS manufacturers, the different types of equipment monitored, and the different type of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along the belt haulage entries. As of December 31, 2009, point-type heat sensors were prohibited for use for an early fire detection system; instead carbon monoxide (CO) sensors are now required. This report will examine the number of AMS currently used in underground mines in the United States to see if there is a change in their use. The locations and parameters monitored by AMS are also discussed. INTRODUCTION The last survey conducted by the Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems (AMS) used in underground coal mines in the United States (US) was in 2003 [1]. The survey report states that since 1995 there had been a steady increase in the use of AMS in underground coal mines as the technology of CO sensors was improved by manufacturers. AMS had become more reliable and some CO sensors could be purchased with the capability to discriminate between the CO produced from a fire versus CO produced from diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed for the miners to take the necessary action to put out the fire or exit the mine. It should also be noted that at the time of last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than using point-type heat sensors [2]. Finally, since the last MSHA survey, regulations have changed on the type of automatic fire detection systems permitted to be used in conveyor belt entries. As of December 31, 2009, point-type heat sensors are not permitted to be used for fire detection in underground coal mines in the US; instead CO sensors are required as a replacement (30 CFR 75.1103-4). This study will examine how the changing of the above regulations has impacted the use of CO sensors in underground coal mines in the US compared to their use based on the last MSHA survey. Importantly, in the previous MSHA survey, the data was recorded for producing and non-producing coal mines. In this study, only the data from the producing coal mines was recorded. Data was collected from a total of 235 coal mines for this study with the help of the MSHA district offices."

Jan 1, 2017

By P. R. G. Brandão

In this investigation, the differences in the absorption spectra of etheramines, fatty amines and condensates, mostly present as acetates, from several suppliers are characterized by means of infrared spectrometry. Sharp differences were observed in the absorption spectra of three types of amines and derivatives. Etheramines show a characteristic and well-defined peak at 1,114 cm-1. This peak is due to the ether C-O group and differentiates etheramines from the other classes. The absence of such a peak indicates that the species is not an etheramine. The distinction between condensates and fatty amines is made by the presence of a sharp peak around 3,200 cm-1. This peak is probably due to the proximity of the N-H amine groups and C=O carbonyl groups in the amide portion of the condensate's molecule and by different and better-defined bands in the 1,800- to 1,500-cm-1 range. The flotation performance of these amines was evaluated by means of the laboratory-scale flotation of an itabirite ore. The etheramines proved to be the most effective collectors for this system. Monoamines presented better performance than diamines for the ore under investigation.

Jan 1, 2002

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989