Search Documents

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

1. Books from Elsevier The folowing are available from Elsevier Applied Science, Crown House, Linton Road, Barking, Essex IGl 8JO, OK. . Driling wastes, edited by F.R. Engelhardt, J.P. Ray, and A.H. Gilam. 1989. 872 pp. £95. Geothermal resources, by R. Bowen. 2nd ed. 1989. 468 pp. £60. The fate and efects of oil in freshwater, edited by J. Green and M.W. Tret. 1989. 340 pp. £42. Mining and the freshwater environment, by Martyn Kely (with contributions by W.J. Alison, A.R. Garman, and C.J. Symon). 1988. 228 pp. £32. 2. Books produced by Metal Buletin The folowing are available from Metal Buletin PLC, Park House, Park Terace, Worcester Park, Surey KT47HY, England. Prices and data 1990. £41 (airmail). Foundry directory and register of forges 1989-1990. £52 (airmail). 2. Canadian Publications The folowing two publications are available from the Canadian Government Publishing Centre, Supply and Services Canada, Otawa, Canada KIA 059. Mining and mineral processing operations in Canada. Mineral Buletin MR 224. $23.70. Canadian minerals yearbook 1989. Review and outlook. Mineral Report 38. $47.95. Technology developments The Mintek Pyrosim Simulator Pyrosim is a computer program for the steady-state simulation of pyrometalurgical processes?.

Jan 1, 1990

Contribution by F.S.A. de Frey The authors are to be congratulated on a job well done by making, in their paper, such a pool of information available to mining engineers. I would like to comment on the following statement: 'As an alternative to the commonly used deep-level mining methods, consideration should also be given to pillar mining at great depths as a logical extension of the current methods. For example, a 75 per cent extraction Or Ryder's discussion The moderate levels if average pillar stress (APS) (320 MPa) are consistent with pillar stability. Squat 10:1 pillars should never 'fail' in themselves, and foundation strengths are also not exceeded (the stresses are well below the 2 ½ x UCS rule-of-thumb provided the foundations comprise normal strong 200 MPa quartzites). Authors' reply We thank Dr de Frey for his contribution to our paper on shallow hard-rock pillar systems. To considerable extent, we share his enthusiasm the potential role of squat pillars in deep-level mining, although we harbour reservations concerning strata control, mining economics, other issues. We agree wholeheartedly that further research, together with carefully planned field trials, is warranted in pursuit of this potentially highly rewarding concept. .

Jan 1, 1995

By C. C. Johnson

In the fourteen years that Rössing Uranium Limited has been in production, the metallurgical operations and controls on the leaching plant have evolved through four basic stages. Initially, the emphasis was placed on the achievement of consistent plant operation by overcoming severe startup difficulties. The second stage involved the attainment of the design operating targets, and also the commissioning of the ferric-leaching reactors in order to achieve a ferric ion concentration of more than 3,0 g/l. Improvements in control then became the priority, with the emphasis on consistently achieving the target concentrations of ferric ions, total iron, and terminal acidity. The latest phase has concentrated on the optimization of costs by means of adjustments to the historically established operating parameters in order to achieve large savings on consumables while maintaining the leaching efficiencies. Apart from the obvious incentive of reducing costs in an inflationary economy and a depressed uranium market, impetus for this work was given by a change in the type of ore from the open pit, which has the effect of reducing the extraction efficiency while increasing the consumption of consumable materials. These problems and their solutions are discussed in detail, and the importance to cost-effective optimization of an accurate, up-to-date cost-reporting structure is stressed.

Jan 1, 1990

By M. U. Ozbay, D. R. Lougher

An in-situ experimental programme was carried out to improve the understanding of the rockmass and pillar behaviour in moderately deep hard-rock mines. The experiments were carried out at Impala Platinum mines and consisted of precise levelling measurements in the footwall of the reef, stress measurements in pillars, convergence measurements in the stope, and petroscope observations in pillars. The results were analyzed using a computer program in an attempt to quantify the characteristic behaviour of the rockmass as well as the pillars. The measured off-reef displacement data were found to co11fonn to the trends obtained from elastic modelling and the correlation could be improved by modelling the small pillars with reduced modulus to simulate yielding' of the pillars. The stress strain curve obtained from analyzing the in situ results, showed that a 6x 3 xl m pillar yields without significant load shedding at peak stress levels of approximately 208 MPa. The closure measurements confirmed that the mechanism of yielding is mainly that of pillars punching into the foundations. Slight to moderate sidewall fracturing and slabbing might be contributing to yielding, but to a much lesser degree than the former mechanism, as the petroscope observation revealed the existence of an intact region beyond 0,6m from the pillar sides.

Jan 1, 1995

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 22nd August, 1979. Dr M. G. Atmore (President) was in the chair and declared the meeting open at 16h00. Obituaries President: It is my sad duty to announce the death of the following Members of the Institute : Brigadier R. S. G. Stokes, Honorary Life Fellow and Past President ; J. A. Arthur, C. L. Cartwright, R. B. Greaves, A. A. Haynes, G. Ross, M. W. Richards, W. T. Stobart, E. Veres, G. V. White, and A. G. Williams, Life Fellows; A. J. H. Pole, D. T. McMurray, P. G. O. Pretorius, A. E. D. Rubidge, A. M. Seccombe, and R. R. Uren, Fellows; R. E. Oltman, R. B. Richardson, and G. P. Rundle, Members; S. F. Dench and S. van Wyk, Associates. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments' silence. Minutes President: May we confirm the minutes of our last Annual General Meeting, which was held on 23rd August, 1978, as published in the November issue of the Journal? Agreed.

Jan 1, 1979

By J. W. Wilson, J. G. Taylor

The mechanization of haulage drilling in the gold mines of Anglo American Corporation by J. w. WILSON, Ph. D., C.Eng., M.AIME, F.!.Min.E., F.I.M.M. (Fellow), and J. G. TAYLOR, A.C.S.M., C.Eng., M.!.M.M. (Visitor) Some one-thousand kilometres of tunnels are mined annually in the gold mines of South Africa. Until two years ago, mechanized drilling on South African gold mines was not an economic proposition because of the availability of inexpensive labour and the fact that mechanized equipment developed for other mining markets could not perform satisfactorily in the tough, abrasive quartzites of theWitwatersrand System. A project team from the Technical Development Services Organisation of the Anglo American Corporation, in collaboration with various manufac turers of drill rigs and drill steel, has been concerned with the development of suitable equipment for mechanized main-haulage drilling. After two-and-a-half years of extensive testing and development of drifters, drill steels, and bits, many of the problems encountered have been sotved, and gradually jumbos mounting pneumatically and hydraulically powered drifters are being phased into production on various gold mines of the Group. A description of the development work is given, and actual operating results are recorded, together with details of the drilling and blasting techniques used.

Jan 1, 1975

By J. D. Austin

Currency fluctuations affect the rand revenues of all exports of mineral commodities, as well as influencing their price on local markets. Of the more than 50 mineral commodities produced by South Africa, about 75 per cent derive 40 to 100 per cent of their revenues from exports. . Although supply and demand are largely beyond its control, management can maximize its revenues despite fluctuating overseas prices and exchange rates by using the right market at the right time. Management can operate in the futures markets, which involve a specific commitment to deliver a specific quantity of a standardized commodity at a set time in the future and at a price that is determined on a futures exchange in open auction; or management can use the options market, in which a producer can insure against the risk of a falling price by taking out a put-option, which gives the holder the right (but not the obligation) to sell the commodity at a stated price at an agreed time in the future. In the forward markets, management has three available tools; forward currency transactions, trading of currency options, and money market hedges. Revenues, currencies of exchange earnings, purchasing power of the rand, and world price trends are shown in over 40 diagrams and tables for the main mineral commodities produced in South Africa.

Jan 1, 1984

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.

Council for 1995/96 President D.A. J. Ross-Watt President Elect Dr N.A. Barcza Vice Presidents Senior R.P. Mohring Immediate Past President J.A. Cruise Junior J.R. Dixon Honorary Treasurer J.A. Cruise

Jan 1, 1996

By J. J. Schoeman

In South Africa and in the rest of the world, the two mica minerals that have the most important commercial value are muscovite and vermiculite. Muscovite has been making a comparatively small but steady contribution to South Africa's mineral exports since about 1960. Vermiculite mining and concentration were started by the late Or Hans Merensky at Phalaborwa during 1946. Vermiculite has enjoyed good overseas sales since then, and during the past four years has become an important earner of foreign currency for South Africa. The various aspects of the micas that could be of general interest are briefly reviewed, such as the history of their exploitation, their mineralogy and chemistry, and their mining, concentration, production, sales, and future

Jan 1, 1989

By K. Sinding

This paper discusses reasons for mining company mergers that have become the fashion, the role of the ?Juniors? and asks what the motives might really be. It examines changes in company concentration over the last 20 years in key mineral segments. Data at different stages of a project are examined to attempt to elucidate the role of the ?Juniors?. Areas for further research are suggested.

Jan 1, 2009

By A. J. Feltenstein

A theoretical model for prediction of dissolved gold loss from a rotary vacuum filter was developed as part of a program to implement optimizing control on gold plants The filter was modelled using a modification of the Hagen-Poiseuille equation and the Choudhury and Dahlstrom washing equation. The model has three parameters which must be determined from accumulated data before predictions can be made. These are the cake and cloth resistances and the filter washing efficiency. The model predicts with a fair degree of accuracy the response of the filter to changes in the independent variables and will therefore be a useful tool in the plant optimization study.

Jan 1, 1987

By D. G. Davies

Colloquium on the construction of Slimes dams The following contributions to the discussion at the above Colloquium were received for publication. D. G. DAVIES* This contribution is really a follow up on Mr H. E. Cross's paper on the conversion of a uranium plant to the recovery of zinc (published in the Journal, November 1973). Ecological aspects of slimes-dam construction by H. T. CLAUSEN C. M. VAN STADEN* Published in the Journal, December 1973 I should like to thank Mr Clausen for his paper and to congratulate the Research Laboratories and the Vegetation Unit of the Chamber of Mines on the excellent work they have done in the past, are still doing at present, and, we hope, will continue to do in future, on the testing of various methods for the covering of slimes dams and specifically on the vegetation of dams. The impact of slimes-dam formation on water quality and pollution by R. T. RUDD* C. M. VAN STADEN Published in the Journal, December 1973 I should like to congratulate Mr Rudd on the paper he presented. Congratulations are also due to the Department of Water Affairs for the practical attitude they have taken in implementing the Water Act. Slimes-dam construction in the gold mines of the Anglo American Group by W. T. RUHMER W. R. FLOOK* Published in the Journal, February 1973 Methods for the construction and operation of slimes dams in the gold-mining industry do not appear to have changed much for some considerable number of years.

Jan 3, 1974

By E. Uslu

The kinetics of the reduction of chromite from the LG-6 layer of the Bushveld Complex in Fe-Cr-C alloys were studied in the temperature range 15OO°C to 1680°C under an inert argon atmosphere. The rotating cylinder technique was used, and the rotational speed of the chromite cylinder ranged from 0 to 1000 r/min. The melt consisted of 30 to 80 per cent chromium and 2 to 8 per cent carbon. The initial chromium-te-iron ratios of the melts varied between 0,42 and 4,95. The reduction of chromite spinel was analysed in terms of the decarburization of the metal. It was found that decarburization increased with an increase in the temperature, the carbon content of the bath, and the rotational speed of the cylinder up to 400 r/min, after which it remained almost constant. Decarburization also increased with an increase in the chromium content up to about 50 per cent chromium but, at higher chromium contents, it decreased. In the early stage of the reduction, up to about 30 minutes of reaction time, the liquid-state mass transfer of oxygen was found to be the most likely rate-determining step. The apparent activation energy was calculated to be 84,864 kJ per mole of oxygen. In the later stage, diffusion of iron and/or chromium in the solid state is the most likely rate-determining step. The apparent activation energy for the diffusion was calculated to be 471,18 kJ/mol.

Jan 1, 1991

By H. L. Monro

The individual supplies of and demands for gold that make up the total supply/demand structure in any year, together with their individual price elasticities, are used to determine the effect of forward sales on the gold price.

Jan 1, 1992

The 88th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on Wednesday, 14th August, 1985. Mr J.D. Austin (President) was in the chair and declared the meeting open at 16h00.

Jan 1, 1985

[Council for 1993/94 President Dr H. Scott-Russell President Elect J.A. Cruise Vice Presidents Senior D.A.J. Ross-Watt Junior P.D.K. Robinson Immediate Past President J.P. Hoffman Honorary Treasurer J.A. Cruise]

Jan 1, 1994

COLLOQUIUM PRACTICAL APPLICATIONS OF INSTRUMENTATION IN THE MINING AND METALLURGICAL INDUSTRIES Rapporteur: J. Laschinger A colloquium and general meeting of the Institute held jointly with the Instrument and Control Society of Southern Africa at Kelvin House, Johannesburg on 18th October, 1972, had as its theme "Practical Applications of Instrumentation in the Mining and Metallurgical Industries" Dr J. P. Hugo (President) was in the chair and about 200 members and visitors were present.