Search Documents

Colloquium and General Meeting A General Meeting and Colloquium was held on 'New Advances in Non-ferrous Pyrometallurgy' in Kelvin House, Johannesburg, on Wednesday, 17th March, 1976. The President, Dr R E. Robinson, opened the proceedings at 1OhOO,by welcoming the authors and delegates, who numbered approximately one hundred and twenty. Tinplate Conference The Tin Research Institute is organizing the 1st International Tinplate Conference, which is to be held in London from 5th to 8th October, 1976.

Jan 6, 1976

By Y. Tanaka, H. Miki, Y. Aoki, H. Okamoto, G. P. W. Suyantar, T. Hirajima

Due to environmental limitations and the scarcity of freshwater, flotation using seawater or desalinated seawater as process water becomes more common for mining operations. On the other hand, seawater has been reported to affect the flotation behavior of sulfide minerals. Few reports are available on influence of pyrite depression, recycled seawater and lime consumption on flotation by using seawater. In this study, the flotation tests were performed using ore sample to investigate the effect of pH with seawater and process water used in plant on the flotation behavior in a laboratory-scale flotation cell and a pilot plant-scale. The results of laboratory scale flotation indicated that copper and molybdenum flotation kinetics decreased with increasing pH. Furthermore, the iron (mainly pyrite) recovery decreased with increasing pH. The pilot plant-scale flotation test showed that water with a higher concentration of magnesium and calcium (plant processes water) consumed a higher amount of lime. Because of low lime consumption and high copper and molybdenum recovery and grade, pH 8 is suitable compared with pH 8.5 for flotation. Keywords: seawater, process water, copper-molybdenum rougher flotation, pH, pilot test

Jan 1, 2020

By F. Bornman

Ore quality is declining, and the current spirals in mineral sands extraction is deemed inadequate to efficiently extract the valuable minerals. A new spiral was developed, the 117HM with the aim to extract the total heavy minerals in the order of 4.0% - 6.0% and the economic heavy minerals in the range 1.0% - 2.2% from the feed. An important measurable in the gravity concentration of mineral sands is recovery. Recovery measures how effectively the separator has extracted the valuable mineral contained in the input stream. The number of turns on the spiral trough influences the residence time of the feed slurry. A further optimisation followed with the development of the twelve-turn 117HM spiral. Four more turns were added for better recovery. The paper quantifies the effect of residence time on recovery.

Mar 30, 2026

By M. Asghari, R. Amiri, A. Haratian, S. Haji

The aim of this investigation is the evaluation of optimising the Shahroud copper ore beneficiation plant near the Iranian city of Shahroud, by means of a sensor-based ore sorter applying X-ray transmission technology. Currently, this plant’s feed capacity of 52t/h produces 0.5t/h copper concentrate with a grade of 30% and copper recovery of 85% from a feed grade of 0.36%. By applying an X-ray transmission-based (XRT) sorter, it is possible to preconcentrate the feed and remove the gangue materials before entering the plant, enabling the production rate of concentrate to be increased. In this study, the obtained representative sample from the plant was preconcentrated in particle size of - 75+10mm by using the X-ray sorter, thus the concentrate with Cu grade of 0.85% was obtained. Therefore, by using of X-ray sorter the Cu grade of plant feed was increased to 0.48%. By increasing the feed grade from 0.36% to 0.48%, and considering a Cu recovery of 85%, the production rate will be increased from 0.48t/h to 0.61t/h. Therefore, the preconcentration by using the XRT sorter increases the production rate by 27%. Keywords: Optimisation, preconcentration, copper, X-ray, sensor-based ore sorting

Jan 1, 2020

By B. M. Kunar

It is well known that job-related hazards and individual factors influence occupational injuries. However, research involving coalminers has been limited. This case-control study assessed the relationships of job-related hazards and individual/life style factors with injuries among underground coal miners. It compared 245 cases with at least one injury during the previous two-year period with 245 matched controls with no injury. The data were gathered via personal interview and analysed using the conditional logistic model. The significant risk factors were materials handling (adjusted OR 5.15), poor environmental/working conditions (2.63), geological/strata control-related hazards (2.35), lack of formal education (3.00), sleep disorders (1.86), alcohol consumption (2.32), disease (2.23), having a large family (5.40), and risk-taking behaviour (9.40). Machine-related hazards, sleep disorders and alcohol consumption primarily affected workers aged less than 45 years; whereas, environment/working condition-related hazards, presence of disease, smoking, risk-taking behaviour and large family size were more likely among workers aged 45 or over. Keywords: Occupational injuries, sleep disorders, job hazards, alcohol, coal miners

Jan 1, 2010

By D. N. Esfahani, K. Khazen, M. Mohammadi

Electrowinning is one of the nickel recovery processes from solutions obtained from the leaching of nickel sources. Every year significant amounts of nickel products are used in various industrial processes and daily life, such as catalysts or batteries, which are a valuable source of nickel for recovery. Nickel purity is also very important in the electrowinning process, because the amount of impurities in nickel such as sulphur, if greater than 100 ppm, make it unsuitable for use in catalysts and plating. Because sulfur is intrinsic to the sulphate electrowinning system, we needed to investigate parameters that can affect the quality and purity of nickel. In this regard, experiments were performed in static and circulating electrowinning processes. A monitoring and circulation system was designed and built to measure voltage, current and temperature as well as to circulate the solution in the system at a specified rate. It was then observed that nickel ion concentration, pH, using the circulation system and additives, were factors affecting the purity and quality of nickel, and in the best case the amount of sulphur in nickel was below 100 ppm. Keywords: Nickel, electrowinning, sulphur impurity

Jan 1, 2020

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By R. Weber

Methane explosions in underground coal mines are a major concern across the mining industry. After the Pike River disaster, Arnot Coal became even more aware of the explosion risk. To determine whether Arnot has adequate precautions against a methane explosion, such as the one that led to the Pike River disaster, a literature survey covering the causes of the incident and what preventative measures should have been in place was conducted. Many different methane explosion prevention methods were evaluated, as well as codes of practice. Based on the findings, Arnot?s measures to prevent conditions favourable for a methane explosion were evaluated.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020

By K. J. Kruger

Aluminium alloys have gained popularity in many industries due to their high strength and low weight. One shortcoming of aluminium alloys is their poor resistance to abrasion and erosion wear compared to materials such as stainless steels. In this project, aluminium alloy 2014 (AA2014) was coated with a 1.5 mm thick laser-deposited layer composed of silicon, copper, and aluminium with the aim of increasing the wear resistance. The amount of silicon, copper, and aluminium added to each sample was determined by a mixtures model. It was discovered that the Al-Cu system is very sensitive to silicon additions and that wear resistance depends on the primary phase to solidify as well as on the final phase distribution. Two primary phases were identified; alpha aluminium and theta intermetallic. It was observed that the clad layer increases both the hardness and wear resistance of AA2014, and that the material solidifying as primary alpha aluminium displayed a lower hardness but higher wear resistance than the samples containing primary theta phase. All clad layers performed better in terms of wear resistance than the unclad samples. The knowledge gained and principles used in this project could be applied to many other aluminium alloys.

Jan 1, 2014

By M. R. Anderton

"A hierarchical four-character code designed for geological and allied data may be used to log exploration drill-holes and store the information on magnetic media. The code is intended for use in semi-free format and permits the collection of as much, or as little, data as the geologist may require for the purpose in hand. A method of data storage by variable length records is discussed.Information may be retrieved by means of a simple enquiry language. Optional output facilities could allow the retrieval of data in a form suitable for direct input to a contouring package. The enquiry parameters and interrogation program can thus provide the interface between the data bank and associated application systems."

Jan 1, 2014

By J. Bullón, A. Pérez

Some years ago, Ferroatlantica developed a new type of electrode known as the ELSA electrode. In this electrode there is a central graphite core that provides support, surrounded by an annulus of Søderberg paste that gets baked during operation. This technology has been implemented on several silicon furnaces around the world, and was reported on during the previous Infacon conference. In all electrodes, but particularly in the ELSA electrode, the quality and consistency of the paste are important for correct operation. As the type of paste varies between customers and between countries, Ferroatlantica has developed a quality control procedure for their customers of this technology. This procedure is geared to the point of view of the customer rather than the paste producer. The analysis is based on the desired flow pattern of the raw paste and on the desired mechanical and electrical properties of the baked paste, as experience has shown that these are the most important parameters to monitor in order to avoid having problems with the resulting electrodes. This paper discusses these methods of paste analysis in the light of complementary studies that have been done when there has been an electrode breakage in the different plants.

Jan 1, 2007

By K. H. Zhang, Y. P. Gao, J. Q. Zhao, Q. Li, J. C. Ma

Compared with sinusoidal oscillation, non-sinusoidal oscillation enhances the ability to control waveform and meets different oscillation requirements by adding an independent parameter, which is the key technology for high-efficiency continuous casting. A new waveform of mould non-sinusoidal oscillation is proposed in this paper, that is, a velocity waveform that is composed only of straight lines and parabolas, which not only has good dynamic characteristics, but also further enhances the feature of non-sinusoidal oscillation. Compared with sinusoidal oscillation, the negative strip time is reduced by 15.9%, the maximum negative strip velocity difference is increased by 38.3%, and the maximum positive strip velocity difference is decreased by 27.8%. The formulas of oscillation process parameters can be clearly deduced, and the isoplethic curves of oscillation process parameters when multi-parameter simultaneously changes are drawn. The negative strip time decreases as the modification ratio, frequency, and casting speed increase, but increases as stroke increases. In order to maintain the stability of negative strip time, an oscillation synchronous control model for optimising oscillation basic parameters was developed. Through practical application, the mean oscillation mark depths decreased by 10.1 μm and the flux consumption is increased from 0.37 kg/t to 0.45 kg/t in the non-sinusoidal oscillation model, which meets the requirements of normal production.

Oct 24, 2025

By T. Steyn, M. Fofana

"One of the most important performance indicators of a dense medium cyclone (DMC) circuit is the Tromp curve, and by extension the separation density and Ecart Probable (Ep) values. The densimetric profiles of DMC product streams have been traditionally acquired using heavy liquid sinkfloat analysis, which has certain disadvantages, such as the associated safety and health risks. More recently, non-toxic media such as lithium hetero-polytungstates (LST) have been used, with the desired densities being achieved by maintaining the solutions at specific temperatures. However, the high costs of these liquids can be prohibitive. The long turnaround time of the sink-float analysis is a further disadvantage for timeous interventions to the operating set-points of the DMC process.The RhoVol technology can generate the density distribution of a batch of particles in a rapid, accurate, repeatable, and safe manner. Additional data of interest, such as particle size and shape, are also measured and reported on a per-particle basis. Furthermore, samples can be sorted into discrete sorting bins based on any of the measured parameters of the particle, making further analyses of the material possible.This technology has applications across all commodities that use the DMC, particularly in the size fractions –25 +8 mm and –8 +3 mm. To date, laboratory results have proved very encouraging – separation densities are within 5% of traditional sink-float results, and the technology is being introduced to diamond DMC plants. IntroductionDense medium separation is a commonly applied beneficiation technique for the density separation of valuable products from crushed ores. The industrial applications of dense medium separation have been summarized and reviewed by various authors (Scott and Napier-Munn, 2000; Bosman, 2014; Napier- Munn, 2018). Dense medium cyclones (DMCs) are widely used in the coal and diamond industries to produce clean coal or to preconcentrate kimberlitic ores, respectively. Cyclone performance (separation density monitoring) techniques are varied. In the mineral industry. Density tracer tests (Napier- Munn, 1985, 2014; Davis, Wood, and Lyman, 1985) without mineral material, are widely used, although their accuracy in predicting operating cut-points becomes limited once mineral material is introduced. More recently, radio frequency tracers have been also used for the determination of cyclone efficiency (Partition Enterprises, 2017)."

Feb 1, 2019

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By F. Wang, P. Rosario, A. Vazirizadeh

Advances in data science, machine learning, and artificial intelligence are transforming mining and mineral processing, and making them more algorithm intensive. The paradigm is shifting from one of detection and control to one of prediction and optimisation. To build up reliable prediction and optimisation models these steps should be passed: collect, aggregate, cleanse, and process large amounts of complex, structured, and unstructured data as a first stage. Next, the right tools must be used to extract meaningful features from the operational data for the build-up of a prediction model. A grinding circuit is one of the challenging areas in terms of determining its overall efficiency and the prediction of product quality. In a processing plant, some of the KPIs are typically unmeasurable or infrequently measured for real-time application, e.g. ore grindability and grind size. However, these variables are required to calculate the grinding circuit efficiency and to model the operation performance. In this paper, advanced analytic tools have been used to extract one selected KPI (cyclone overall P80 or final grind size) and its relationship with measured variables for an industrial dataset. The results illustrate that the performance of the grinding circuit can be predicted for real-time monitoring by means of measured data. Keywords: Grinding circuit, data-driven, machine learning, process modelling, hybrid modelling

Jan 1, 2020

By P. Leeuw, H. Mtegha

"The aim of this paper is to enhance the understanding of the nature of mining input technologies in the South African mining industry. In the context of this research, mining inputs refer to input technology into the activities in mining engineering fields, which include mining-related production activities, rock engineering, mine ventilation, and mine transportation (handling of personnel, material, broken rock, and pumping). Input technologies in supporting fields such as geology, other engineering disciplines, human resource, procurement, finance, as well as downstream fields that include metallurgy, and marketing of minerals, were disregarded.The mining input technologies were divided into 12 nodes, and data from a sample of 150 first-tier mining suppliers was analysed. It was found that, in general, there is a high local content in mining input technologies, particularly as regards technical support services, artefacts, and machine technologies. This points to the presence of mining-induced backward linkages in the South African mining industry. The majority (83%) of companies that provide input technologies into mining are located in Gauteng Province, and relatively few are found in provinces where mining is concentrated such as North-West, Limpopo, Mpumalanga, and Free State. IntroductionSouth Africa is well endowed with minerals, with more than fifty different minerals being mined throughout the country. For this and other reasons, mining is one of the crucial pillars in the South African economy and its importance is well documented (Robinson and von Below, 1990; Creamer, 2010; Department of Mineral Resources, 2015). In 2013, South Africa was the largest global producer of chromium, ferrochrome, platinum group metals (PGMs), and vermiculite and the second largest global producer of antimony, manganese, titanium, and vanadium (Chamber of Mines of South Africa, 2014). In 2013, the mining industry contributed 6.7% to South Africa’s GDP and was the fifth largest sector in the economy, as shown in Figure 1."

Jan 1, 2016

By L. Kühnel, H. Lieberwirth

Confined bed comminution in High Pressure Grinding Rollers (HPGR) and Vertical Roller Mills (VRM) is gaining substantial attention in many applications. Previously used mainly for milling coal or construction materials, HPGR and VRM have started to complement or even replace tumbling mills in ore beneficiation. Materials like coal or clinker are relatively homogenous, however, in comparison to metal ores and wall rocks. This characteristic poses a new challenge to the confined bed comminution but also an opportunity. Fuerstenau and Abouzeid have investigated the selectivity in comminution of a mixture of particles of different strength in a particle bed. The median particle size and particle size distribution (PSD) of the two constituents used were kept constant. Only the proportion of the two constituents was modified. The competence of a material is, however, also a function of particle size. Smaller particles tend to be more competent than larger ones of the same material. If selective comminution is applied on ores, this size influence has to be understood. The paper presents research results on this topic based on experimental investigations with model materials as well as with natural particles, which were stressed in a piston-die press. It appeared that the comminution result depends substantially on the material characteristics and the composition of the mixture. Conclusions will be drawn for the application in future applications of selective comminution in mineral processing. Keywords: Confined bed comminution, HPGR, VRM, piston die press, particle size

Jan 1, 2020

By D White, L. Lorenzen

Sampling and metallurgical testwork during various phases of engineering studies is of paramount importance for a robust processing plant design. When developing a process flowsheet, risks in achieving desirable financial outcomes are minimised by ensuring that appropriate sampling and adequate metallurgical testwork support the engineering and cost estimation at each phase of project development. The quality and type of samples used for metallurgical testwork are just as important as the metallurgical testwork itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should consider the spatial orientation, lithology, alteration, degree of oxidation, mineralogy, and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical testwork program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design. The authors have observed that the quality of sampling and quantity of metallurgical testwork carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are based on benchmarks of apparently similar ore bodies or rely on buoyant metal prices supporting cash flows until rectifications can be implemented. The paper will discuss important aspects of sampling and testwork required for engineering studies in designing process plants. Keywords: Sampling, metallurgical testwork, studies, design

Jan 1, 2020

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022