Search Documents

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated in the sintering process to produce sinter: an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the sinter bed height and time dimensions. This method can further be used for establishing empirical relationships with measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions that vary over time. Sub-models describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. Four sinter pot tests were performed and the model predictions validated against temperatures measured at depths of 100, 230, and 420 mm. Differences between predicted and measured temperatures indicated the need for optimization of some model parameters that are uncertain. Optimization resulted in an improvement in the correlation between the predicted and measured temperatures for all tests, although an acceptable level of agreement was not achieved in all cases. Using these parameter values, reasonable agreement was found in terms of typical performance parameters for three out of the four tests.

Jan 1, 2014

By P. J. Foster

This paper summarizes a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialed at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this, a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By J. Palarski

Long waling is used in most Polish coal seams, with backfilling to support the roof, to create an artificial hanging wall to prevent movement if the rockmass, and to eliminate the fire hazard in abandoned mine workings. This paper discusses the results if tests conducted on 7 different backfill mixtures, and gives equations for the estimation if the flow if backfill slurries through gravitational pipelines.

Jan 1, 1994

By E. Lwamba

The aim of this study was to examine the effect of grain size distribution control of the raw material mixture on the permeability of the green sinter bed and the properties of the produced sinter. This was achieved by evaluating the granulation characteristics of the sinter mixture (moisture content, granulation time and mean granule diameter) in terms of its green bed permeability, and evaluating the productivity of the sinter bed, the coke rate, tumble index (TI), abrasion index (AI), reduction disintegration index(RDI) and reducibility (RI) of the produced sinter. The raw sinter mixtures contained combinations of Thabazimbi iron ore, Sishen iron ore, coke, lime and return fines. The grain size distributions were controlled by removing the ?0.5 mm size fractions of the return fines and coke, and the ?1 mm size fraction of lime. Of the examined mixtures, a mixture of 20 mass% Thabazimbi iron ore, 80 mass% Sishen iron ore and fluxes where the coke, lime and return fines were all sized had the highest granulation effectiveness and permeability. The sintering properties of the mixtures in which the grain size distributions were controlled, were very similar for all the mixtures, but superior to the base case mixture in which the grain size distribution was not controlled. Keywords: Thabazimbi iron ore; Sishen iron ore; granulation, permeability, grain size distribution; sinter.

Jan 1, 2008

By M. Keevy, K. Hackney

Centrifugal slurry pump station and deposition sites are a common feature of many mines and mineral processing plants. Yanacocha Mine has completed the design of a pump station consisting of two trains of four pumps each. A number of trade-off studies was conducted to optimize the pump station design. The most significant of these was determining the drive types for the slurry pumps. The pump station duty can vary considerably due to the number of deposition points round the disposal site. The standard solution to this problem on a multi-stage pump train is to install one pump with a variable speed drive to control the pump station output by varying the speed of this pump and stopping and starting other stages. However, there are a number of negative impacts associated with this approach. These include head losses through pumps that are stationary or ?wind-milling?, different wear life on pumps that are running and pumps that are stationary, and slower response to the control system with the possibility of hunting. The use of variable speed drives on all the pumps was considered as an alternative to the standard solution. The factors considered in comparing these options were the control and operational differences, the pump efficiencies and absorbed power, the expected pump wear life, the impact on pump maintenance and the cost of the drive options. For this project the option of using all variable speed drives was selected. The paper presents the following aspects of the study: ?Description of the various options investigated. This includes a discussion on the required duty and the drive options. ?Technical comparison between the options. ?Description of the factors influencing pump performance and life.

Jan 1, 2007

By J. C. Steinhobel

Answers to questions raised at the Symposium on Trackless Mining in Metal Mines Questions by J. O. Steinhobel (1) When rubber-tyred equipment is used for the delivery of stores and items of equipment, how is heavy material-pipes, rails, timber support, ventilation columns, etc.-dealt with? Termination of Membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register.

Jan 9, 1973

Sampling In The Coal Industry Exploration, Mine, Met and Environmental Sampling EMMES 2005 3, 4 November 2005

Jan 1, 2005

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

By C. F. Vos, J. D. Miller, J. C. Davidtz

"This work presents the potential for improving the flotation recovery of slow-floating sulphide minerals with the use of starvation dosages of a normal dodecyl (n-C12) trithiocarbonate (TTC) co-collector, together with a sodium isobutyl xanthate (SiBX) and dithiophosphate (DTP) collector mixture.At potentials below –150 mV (SHE), addition of nC12-TTC with SiBX improves the hydrophobicity of pyrrhotite, yielding captive bubble contact angles greater than those measured for SiBX or nC12-TTC alone, suggesting a low potential synergistic effect. This synergistic effect is further studied using Fourier transform infrared (FTIR) spectroscopy, the results indicating an increase in the surface concentration of the collector species when in a mixture. Thus, nC12-TTC with SiBX may act as an immobile surface anchor to which SiBX/SiBX2 molecules bond, increasing the localized concentration of collector species.Bench-scale flotation tests using mixtures of SiBX/DTP/nC12-TTC on a platinum group element (PGE)-bearing ore from the Bushveld Complex in South Africa confirm an improved metallurgical performance at very low substitutions (approx. 5 molar per cent) of SiBX. The improved recoveries for PGE, Cu, and Ni are correlated with improvements in the flotation kinetics of their slow-floating components. IntroductionShort-chain (less than C6) xanthates are very effective for the bulk flotation of sulphides (Fuerstenau, 1982), and early work (Leja, 1968; Gaudin, 1957; Plaksin and Bessonov, 1957; Taggart, Giudice, and Ziehl, 1934) indicated that the presence of oxygen in flotation slurries is necessary for the oxidation of the xanthate collector at the sulphide mineral surface to induce hydrophobicity. Fundamental research into the chemistry and adsorption mechanisms of xanthates over the years (Finkelstein and Poling, 1977; Woods, 1976; Winter and Woods, 1973) has revealed that for iron-bearing sulphide minerals, adsorption occurs predominantly through a charge transfer process. Oxidation of the adsorbed collector to the corresponding dimer takes place if the mixed potential of the system is greater than the reversible potential for dimer formation. In oxygenated slurries the rate of adsorption and oxidation of the collector depends greatly on the substrate surfaces. For chalcopyrite (Guler et al., 2005; Leppinen, 1990; Roos, Celis, and Sudrassono, 1990) and pentlandite (Hodgson and Agar, 1989) a two-step interaction with xanthate is proposed in which the chemisorbed xanthate is further oxidized to the dimer. The initial interaction of xanthate with pyrrhotite is through physisorption where xanthate physisorbs onto positive surface sites followed by oxidation to dixanthogen (Khan and Kellebek, 2004; Bozkurt, Xu, and Finch., 1998). This process is, however, slow and increased reaction time is needed to improve flotation recovery (Buswell and Nicol, 2002)."

Oct 1, 2018

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By E. J. Maunders

This paper describes briefly a computerised model of the South African electricity system which has been developed jointly by the Atomic Energy Board and the Electricity Supply Commission. The results of an analysis of this system have been subjected to a fairly extensive sensitivity analysis which reveals that up to the year 1990 between 680 and 700 million tons of coal will be required for electric power generation, together with between 7 000 and 10 000 tons of uranium. This result is fairly insensitive to data variations, but the prediction of a cumulative requirement up to the year 2000, of between 1 300 and 1 800 million tons of coal and 25000 to 70000 tons of uranium, proves to be very data-sensitive.

By J. Stacey

There are four components to this guideline 1. Guidance on the socio-economic aspects of closure policy 2. Socio-economic closure activities mapped against the mining project life-cycle (a ?check status? tool) 3. A process guide for mine closure planning and implementation 4. Tools in support of mine closure planning and implementation How to use this guideline The four components are part of a hierarchy with: ?Overarching policy as the starting point ?The mine life cycle model as a quick process check tool ?The process guide for detailed practical planning and implementation as practical guidance ?Supportive tools as resources to address specific planning and implementation steps.

Jan 1, 2010

By E. Keskinkilic

Drying, calcination, prereduction, and smelting are the main steps in conventional crude ferronickel production. Industrially, these steps are conducted using the rotary kiln-electric arc furnace (RKEF) process. In this paper, calcination characteristics of Sivrihisar laterite ores from the Central Anatolia region are investigated. The extent of elimination of chemically bound water and other volatiles was studied by experiments conducted at various temperatures in the 250?800°C range. Phase changes were examined using X-ray diffractometry. For the particle size used in the study, 300°C was determined to be almost sufficient for complete transformation of goethite to haematite, and 700°C was required for effective elimination of all volatiles in the ore.

Jan 1, 2012

By G. E. Blight

Several aspects of the behaviour and properties of backfills consisting of cemented cyclone underflow tailings are illustrated by means of examples, and guidelines are given on the optimization of the performance of cemented fills. The stretch characteristics of the geofabric used to contain freshly placed backfill are described, as well as the relationship between these characteristics and the forces acting on retaining barricades. The properties required to achieve a self-supporting, stable free face in cemented backfill are explored, and a graphic relationship between stable height and shear strength is presented and compared with that for uncemented (classified) tailings. After a description of the characteristics of Witwatersrand quartzite gold-tailings backfill and commonly used cements, the process of drainage and air entry into backfill is outlined. Following this, the early-age gain in strength and the shear-strength characteristics, as well as the compressibility characteristics of cemented backfill, are described. Two phenomena that are potentially damaging to cemented backfill are seismic effects (or blasting acceleration) and the closure that takes place during the curing of cement. Investigations show that neither of these phenomena is actually significantly deleterious to gold-tailings backfill: liquefaction does not Occur as a result of seismicity, and hydration of cemented fill is not significantly impeded by closure.

Jan 1, 1996

By Mike Rogers

Platinum production in Southern Africa amounted to 80% of world production in 2005with a small increase from 5 117 000 ounces to 5 275 000 ounces. For the seventh consecutive year the platinum market is on course to record a moderate deficit in supply. This is reflected in the price increase from a trading range US$860 to US$880 in June 2005 to an excess of US$1 200 in September 2006. Southern Africa, with its extensive platinum reserves, will continue to be the dominant platinum producer and has a number of new mines in an advanced stage of planning. The slogan ?Platinum Surges Ahead? was selected to describe the exciting and vibrantnature of all aspects of platinum mining, beneficiation and marketing. This conference will cover these aspects from exploration and orebody delineation, through mine design, development and operation to mine closure; mineral beneficiation, marketing and compliance with the Mining Charter will also be subjects for discussion and debate. It is also anticipated that the issue of overall increases in productivity, through the introduction of technology, will demonstrate Southern Africa?s status as a premier mining district. It is my pleasure to welcome delegates from abroad and locally, on behalf of the SAIMM, to the Second International Platinum Conference ?Platinum Surges Ahead?. I trust that you will find the proceedings informative and value adding and will participate in the discussions and debate in order to obtain maximum benefit from the conference. I am sure that the post-conference tours will be interesting and of great benefit to participants. Finally, a big word of thanks to the members of the Organising Committee, the management and staff of the SAIMM, and to our willing sponsors, without all of whom this conference would not have been possible.

Jan 1, 2006

By A. C. Lawrence, K. F. Mauer

Human factors in stope productivity -a field experiment by K. F. MAUER, M.A. (Visitor), and A. C. LAWRENCE, B.Econ., D.Com. (Member) An experiment in which three human variables were manipulated in eight stopes was conducted in a gold mine over a period of roughly six months. The three variables, which each had two levels, concerned the degree of movement from gangs, the quality of the Bantu production supervisors, and the extent to which gangs were composed of a single ethnic group (Malawians). Time was included as a variable with three levels in the analysis of the findings. On the average, stable gangs produced 12 per cent more than gangs with a high percentage of transfers, gangs with better production supervisors were more successful by nearly 9 per cent than those with poorer production supervisors, and homogeneous gangs were more productive than heterogeneous ones by as much as 15 per cent. In addition, it was found that a number of the variables exercised a joint influence on stope productivity and that the effects of the variables were accentuated by the len gth of time they had been in operation. V

Jan 10, 1973

By A. S. Ratnayake, H. C. S. Subasinghe

In this study, we review the role of mechanical activation in the pyrometallurgical, hydrometallurgical, and electrometallurgical processing of titanium feedstock. Mechanical activation has been shown to decrease the activation energy of chemical reactions, thus enhancing process efficiency and product quality by reducing processing time and energy consumption. Pyrometallurgical processing is energy-intensive and time-consuming. Hydrometallurgy is costly, requires high-grade feed material, and generates toxic waste. Waste generation and process complexity are the major drawbacks of electrometallurgy and solvent extraction. Bioleaching via a mechanically activated pyrometallurgical process can be identified as an alternative method, but the lengthy processing time is the major disadvantage. Mechanically activated titanium concentrate can be used in a finely tuned combined metallurgical process to overcome the challenges and drawbacks in these technologies.

Aug 3, 2023

This paper describes the extraction of gold, as the anionic aurocyanide complex, from solution by strong- and weakbase anion-exchange resins. The effects, on the rate of extraction and the loading capacity for gold, of parameters such as pH, temperature, ionic strength, agitation, and the presence of competing anions are reported. The elution and regeneration of strong- and weak-base resins will be examined in a second paper. A third paper in this series will present the results of several smallscale pilot-plant investigations carried out with strong- and weakbase resins In cyanide pulps from various South African gold mines, and will compare the metallurgical performance of resin-In-pulp with that of the carbon-in-pulp process.

Jan 1, 1984