Search Documents

By K. J. Craig, M. A. Swart, Q. G. Reynolds, L. Hockaday

A solar reflector soiling study was carried out at a ferromanganese smelter in South Africa to assess the soiling rates at different locations around the plant. Several meteorological parameters were monitored to give insight into the conditions that lead to increased soiling. Mineralogical characterization of dust samples collected from the reflectors and the atmosphere revealed that only a certain size fraction is of importance with regard to soiling, and that the dust can be attributed to both raw materials and smelter products. Proximity to the dust source was the primary driver for increased soiling. The site that experienced the most soiling was very close to raw material heaps; this was deemed an outlier and was excluded from the summary statistics. The secondary driver for increased soiling was location relative to the smelter dust sources and the wind’s direction and speed. The reflector set at the best location experienced 13.1% less soiling than the set at the ‘worst’ (but still feasible) location, represented by an averaged mean daily reflectance loss of 0.0186. The study revealed that while there are periods of intense soiling at this particular site, proper planning of reflector location in relation to the smelter dust sources can significantly mitigate the soiling rate.

Jun 5, 2023

By B. P. Watson, A. Carpede, W. O. Kekana, N. Fernandes, W. Theron, M. P. Mahlangu, G. Betz

The research described in this paper was done to confirm the Upper Group 2 (UG2) PlatMine peak pillar strength formula (Watson et al., 2007), which was determined from a back-analysis of failed and unfailed pillars. Underground measurements were made on a stable pillar that was loaded by firstly reducing it’s length and then by mining the surrounding pillars until pillar failure took place. The pillar was instrumented with suitably positioned strain cells and closure meters, which allowed both the average pillar stress and strain to be determined. The paper describes the methodology applied to identify a suitable position for the instrumentation, as well as the results. A stress/strain curve is presented for a UG2 pillar with a w/h ratio of 2.0, at Booysendal Platinum Mine. The measured pillar strength was similar to the predicted strength using the PlatMine pillar strength formula for UG2 pillars. The PlatMine formula has been successfully implemented on Booysendal Platinum Mine, and about 3 670 pillars have been cut without a single failure. An additional revenue of US$1.3 billion was calculated for the 25-year life of the mine as a direct result of the improved pillar design, given the January 2020 platinum group metals basket price. An extended life of mine and better mining efficiencies will also be realized.

Aug 1, 2021

The response was good-one of the best the SAIMM has had to its various questionnaires. 231 replies were received from 2768 members representing a response of 8,35%. For fellows and Members together, the response was 13,7%. The spread of responses based on respondents' work situation appeared to be well balanced with some bias from those in consulting organizations. Members' perceptions of their employers' positions withrespect to environmental management looked somewhat optimistic, but it is encouraging to note that they reported that more than half were developing environmental management systems. Training of varying degree was taking place at al levels in their organizations. Members saw their Institute as an important agent inlifting environmental awareness, literacy and responsibility not only through the journal and symposia, but also by liaison with government departments and educational institutions. Most respondents saw environmental legislation both from local and overseas sources as affecting their organizations, their products and services with the emphasis on corporate image, core business and sales.

Jan 1, 1995

By V. Quezada, Á. Astudillo, L. Valásquez, M. Garcia

Seawater has become a viable alternative for different uses in copper hydrometallurgy. In this paper we review the main physical and chemical characteristics of seawater and how these influence copper production. Reliable data on the use of continental water are reported, and the current use and consumption of seawater in the Chilean mining industry is analysed, indicating the main areas of use and the main problems encountered. Additionally, the influence of the elements in seawaterthat have the most influence on the extractive metallurgy of copper are considered. The Chilean copper mining industry currently consumes approximately 4.1 m3/s of seawater, which corresponds to 25% of the total water used. The use of seawater for the leaching of copper sulphide minerals, such as chalcopyrite, is beneficial because it provides 20 g/L of chloride, thereby improving copper dissolution kinetics.

Jul 5, 2023

By R. J. Quevedo, Y. A. Sari, S. D. McKinnon

The large scale of cave mines leads to many challenges, including operational logistics and geomechanics design. In current practice, pillar stability assessment relies almost exclusively on stress analysis. However, stability is also affected by other factors including those related to operational aspects of the mining method, the effects of which are difficult to account for during the design stages. In this paper we present a case study of the application of a machine learning approach to evaluate the influence of these operational factors on pillar stability at the Chuquicamata underground cave mine in northern Chile. Due to the likely multi-factorial damage process leading to collapses and considering the different pillar conditions, a tree-based machine learning method was used and analysed to improve the understanding of the relative importance of the various contributing factors. Unlike stress analysis methods, it does not require any a priori knowledge of failure mechanisms, nor the calibration of associated controlling parameters. The proposed random forest model predicted pillar collapses with 80% accuracy despite limited samples to model from. The main contributing factors to collapses were found to be related to available pillar volume, cave front geometry, and time under abutment stress conditions. The effects and interactions of such factors were also studied, showing that careful and improved control over operational conditions can significantly reduce the likelihood of pillar collapses. These conclusions could not have been obtained from stress analysis alone, illustrating the complementary nature of conventional stress analysis and machine learning approaches.

Mar 14, 2024

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

By N. Theron, R. F. Meeser

The global emphasis on conserving energy resources has led to the adoption of hybrid power systems in vehicles. Optimally applied, hybrid systems can save up to 40% on fuel costs. To optimally manage a hybrid vehicle's energy flow it is necessary to know, in real time, all the energy requirements to complete a given route. The energy consumption depends mainly on the vehicle mass, speed profile, and route topography. Of these, the topographic profile is the one factor that is only route-dependent and not influenced by the vehicle or driving styles. The heading vs. distance profile is also an example of a route characteristic not influenced by the vehicle or driving style. In this study the topographic and heading profiles are used to identify routes, and are easily measured by means of digital barometric pressure and compass sensors. Correlations between the current route and previously travelled/stored routes are performed based on their topographic and heading profiles in a point-by-point manner. Above-ground tests were first performed using a road vehicle and six routes to evaluate the system. The system consistently and correctly identified a 20 km route within the first 4 km. It also proved to function correctly in underground tests through the implementation of an instrumented hand-held surveyor's wheel. This system finds direct practical application in optimizing the energy management of an underground hybrid locomotive used by the mining industry in South Africa, but can also be of benefit in applications where route identification is required and using GPS is not feasible.

Jan 26, 2023

1. Book reviews Geostatistics for natural resources characterization, edited by G. Verly, M. David, A.G. Journel, and A. Marechal. Hingham (MA 02043, U.S.A.), D. Reidel Publishing Co., 1984. Pt I: 606 pp. Pt 11: 518 pp. U.S.$135,50 per set. Reviewer: D.G. Krige Magnesium, the international perspective, by Peter King. London, Financial Times Business Information Ltd, 1984. £120. 147 pp. Reviewer: D.G. Maxwell 2. Mintek reports Report M156 A kinetic study of the reactions of certain gaseous sulphur compounds with iron. Report MI57 Reaction mechanisms in the reduction of Winterveld chrome spinel with graphite and carbon. Report MI72 Computer programmes for the control and datamanipulation of a sequential X-rayfluorescence spectrometer. Report MI77 A proposed test for the determination of the grindabi/ity of fine materials. Report MI86 A survey of the erosion, corrosion, and abrasion of material-handling systems in the mining and mineralprocessing industry. 3. New journal Advanced materials & processes, issued monthly by American Society for Metals (Metals Park, Ohio 44073, U.S.A.). CIM conference The combined 24th Annual Conference of Metallurgists and the 15th Annual Hydrometallurgical Meeting will be held in Vancouver from 18th to 22nd August, 1985. Light metals The 8th International Light Metals Congress will take place from the 22nd to 26th June, 1987. These meetings, which take place traditionally every few years, are organized by the Austrian Metals Industry Association, the Austrian aluminium industry, and the University for Mining and Metallurgy in Leoben, in collaboration with the Aluminium-Zentrale Diisseldorf. President of AS&TS* Mr Arthur Woodington Reynolds (Sam) took office as President of The Associated Scientific and Technical Societies of South Africa on 28th November, 1984. Sam Reynolds was born in Boksburg on 27th December, 1930, and received his education at Christian Brothers College in Boksburg and at St John's College in Johannesburg. World mining Sweden, Finland, and Norway expect representatives of all mining countries in May-June 1987 to the 13th World Mining Congress in Stockholm. The Swedish Mining Association, the Finnish Association of Mining and Metallurgical Engineers, and The Association of Norwegian Mines will organize the Congress, together with the International Organizing Committee of the World Mining Congress. Sheet metal The German Group of the International Deep Drawing Research Group (IDDRG) will be organizing the 14th Biennial Congress of the IDDRG on 21st to 26th April, 1986, in Cologne and Munich. Safety in mines The 21st International Conference of Safety in Mines Research Institutes is to be held in Sydney from 20th to 25th October, 1985. ILAF A conferences The Instituto Latinoamericano del Fierro y el Acero (ILAFA) has scheduled the following congresses for 1985. Mechanical testing of materials The Deutsche Gesellschaft fiir Metallkunde, together with the Deutschen Verband fiir Materialpriifung and the Fachhochschule Osnabriick, is holding a course on the methods used for the mechanical testing of materials at Osnabriick from 9th to 11th September, 1985. Mine ventilation The Second U.S. Mine Ventilation Symposium will be presented from 23rd to 25th September, 1985, in Reno, Nevada, by the University of Nevada-Reno's Mackay School of Mines and Division of Continuing Education.

Jan 1, 1985

By J. H. Viljoen, C. H. Graan, N. B. Strydom, J. S. Greyson

M J Martinson (Fellow) There is everywhere a lamentable dearth of quantitative information on occupational factors affecting the health and safety of mineworkers, and as the authors point out in their introduction underground lighting is one of the factors which has received little attention in South Africa prior to this welcome paper. Since the authors are to some extent pioneering, it is perhaps inevitable that the paper should raise more questions than it answers, but nevertheless it provides a provisional yardstick against which the need for, and success of, remedial action may be judged. Before commenting in detail on a few aspects of the paper it may be worthwhile to summarize the statutory provisions relating to underground lighting, contained in Chapter 15 of the Regulations promulgated in terms of the Mines and Works Act 27 of 1956. Chapter 15 is entitled `Lighting, Safety Lamps and Contraband', but in the context of the present paper only four simple regulations need be noted: firstly, no person shall work or travel in an unilluminated part of a mine unless he carries a light ; secondly, adequate stationary lights shall be provided at stations and certain other localities in shafts, winzes and places used for winding; thirdly, mechanically propelled conveyances shall be provided with an effective bright light shining in the direction of travel; and fourthly, moving machinery to which personnel have access shall be illuminated so as to be clearly visible. In all four regulations the standard of lighting to be provided is wholly subjective, and under these circumstances the wide inter- and intra-mine variations in light intensity disclosed by the study are hardly unexpected. Nevertheless the data presented in the authors' Table I raise three points (1) Is there any evidence that the 19 mines visited during the survey are representative of the 45-50 large gold mines in South Africa, or that the shafts selected are representative of the respective mines? Mine managers would scarcely be human were they not to offer better lit working places for the survey; perhaps the use of a scaling factor (e.g. tonnes or transit mineworkers per shift, kilowatts, etc.) for each working place might have helped to put the figures in perspective. (2) Looking at two of the more numerous - and probably important - of the ten working places included in the survey, i.e. stations and tips, one is struck by the marked. skewness of both intensity distributions (with higher frequencies at the lower intensities) and the abrupt cut-off in both cases just short of pitch darkness. Thus, of the 45 meaned readings recorded at 26 tips no less than 19 fall in the lowest range of 0,1-0,9 1m/ft2, with but one tip in total darkness; of 46 readings on 26 stations, 7 fall in the lowest range and none is in total dark-'1 ness. Although a light with an intensity in the range 0,1-0,9 1m/ft2 may satisfy the regulations, it is certainly arguable that in some situations it may be safer to have no light at all. (3) In view of the skewness referred to above, one wonders how meaningful are the `total average light intensities for (the gold mining) industry' quoted in Table I, which the authors compare with illumina¬tion levels found in other countries. Looking at tips again, one notes that 34 out of 45 meaned intensity readings fall below the `total average' for tips, and only 10 exceed it. From this it may be concluded that a few well-lit working places included in a `total average' may conceal a plethora in Stygian gloom. In their discussion the authors make fleeting reference to the effect of underground lighting on productivity and accident rates, without however quoting any South African experience in this regard. Intuitively it seems highly likely that better lighting (in the widest sense) would improve productivity and reduce accidents, and of course it is in these areas that the mining industry might seek economic justification for providing better lighting. It is all the more regrettable therefore that these factors were not studied simultaneously with the present investigation, especially at the Psychological Division of the Human Sciences Laboratory has recently published a study on underground accidents in the gold mining industry without making any reference whatsoever to lighting as a causal factor. In the event neither of the two studies enables us to make an economic appreciation of the situation, and this seems to be a classic example of a situation where some dovetailing of research effort would have greatly increased the useful return. On the effect of lighting on accidents, it may be noted that in 1939 Mickel presented some very interesting statistics to the Mine Managers Association of the Transvaal2, on the improvement in accident rates which followed the random issue of electric cap lamps to native mineworkers in the Hercules Section of E.R.P.M. the previous year. Based on a 12 month trial period in which 250 000 shifts were worked with carbide lamps and (contemporaneously) 307 000 shifts with cap lamps, the incidence of major accidents (at least one day in hospital among men using carbide lamps was 1,15 accidents per 1000 shifts, while the incidence of minor accidents (requiring dressing only) was 11,52 per 1 000 shifts. The corresponding figures for men using cap lamps were 0,79 and 7,31 accidents per 1 000 shifts respectively, representing a reduction of over 30 per cent in both major and minor accidents. While these figures are obviously dated - only men using cap lamps were issued with hard hats, for instance - they do indicate a need for similar research today.

Jan 1, 1971

By A. F. Spinks, S. P. Nicholls

"The Lower Orebody at Chingola Division of Nchanga Consolidated Copper Mines, Limited, is a stratified orebody that is mined by a continuous caving system. The accurate determination of the developed and semi-developed ore reserves has always been difficult. The new system proposed in 1971 is designed to update and, as new informa¬tion becomes available, to account for the depletion of, the reserves.There are three main inputs to the system. These are borehole data, survey data and extractions data. The borehole data are input to a geological borehole master file system, which holds every recorded detail of a borehole in an easily extractable form. These data can be extracted for ore reserve calculations or for contour mapping of orebodies and rock types. The grades for use in the ore reserve calculations are extracted from the relevant boreholes.The survey data are information on the position of the blocks and drifts, taken from plans, and information on the scraper drift and trough drive positions taken from sections. The information is extracted from the plans and sections using a D Mac pencil follower. The ore reserve is calculated from the survey data and the borehole data.Data on extractions are taken from scraper operators' logs, tramming records, skips hoisted records and accepted mill tonnages and grades. Using these data, the mill tonnages are reconciled back to the drifts, to deplete the current ore reserves.As new workings are brought into operation and further evaluation holes are drilled, the relevant data are input and the new developed ore reserve is calculated."

Jan 1, 2014

By A. W. Cramb

A three-day symposium on the production of clean steel organized by The South African Institute of Mining and Metallurgy, was held in September 1995 at Vanderbijlpark. It was attended by 151 delegates, who represented the whole of the steel industry in South Africa: Iscor Works, Saldanha Steel, Columbus Stainless, Highveld Steel & Vanadium, Iscor Research & Development, University of Pretoria, and Technikon Witwatersrand, as well as the users of steel products were represented. Professor Allan Cramb held the delegates attention with well-presented research and practical information. He obtained excellent interaction with the delegates by responding in depth to the questions put to him during the Symposium. In summary, he emphasized the following aspects of the elimination of defects during the processing of steel in continuously cast materials.

Jan 1, 1996

By B. P. Watson, D. P. Roberts, R. A. Lamos

The Upper Group 2 (UG2) chromitite reef is a shallow-dipping stratiform tabular orebody in the South African Bushveld Complex, which strikes for hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 500 m. Pillars are widely used to support the open stopes and bords. Little work has been done in the past to determine the strength of pillars on the UG2 Reef and design was done using formulae developed for other hard-rock mines. This has led to oversized pillars with consequent sterilization of ore. In this paper we describe a back-analysis of stable and failed UG2 pillars on the Bushveld platinum mines, and provides a strength formula for UG2 pillars. The formula may be used cautiously on all Bushveld platinum mines with similar geotechnical, geometrical, and geomechanical conditions to the pillars in the database.

Aug 1, 2021

By M. Paricheh, M. Rahmanpour

"The cost efficiency and high reliability of semi-mobile or combined in-pit crushing-conveying (IPCC) and truck systems, compared to conventional truck-shovel systems alone, make them more attractive for use in modern mining operations. Semi-mobile systems, which are the most common systems in open-pit mining, combine the advantages of both systems such that fewer trucks are required, operating costs are lowered, and the operation is environmentally sound. One major aspect of utilizing this system is determining the location of the in-pit crusher and the timing of relocations. Facility location models are rarely used in the mining sector, but these models may be used for solving the in-pit crusher location problem. To this end, the main parameters affecting the IPCC location in open pit mines are reviewed and examples given of how they are applied to a dynamic location-relocation problem. Subsequently, the model is implemented for Sungun copper mine in Iran and the number and the exact time of relocations of the IPCC units determined. IntroductionNowadays, compared to the last century, metal prices are more volatile, average and cut-off grades have decreased, and stripping ratios increased. From a mining engineering point of view, many ore deposits with simple access and low capital and operating costs have been exhausted. The remaining deposits are located at depth, with no easy access, which requires high initial capital costs (Osanloo, 2012). Mining at great depths and high tonnages is possible only through open pit mining. Today, more than 80% of open pit mines in the world use a shovel-truck system for loading-hauling operations (Osanloo, 2010).With increasing depth, haulage distances increase and the number of loads per truck decreases. As a result, fuel, tyre, and depreciation costs per ton increase. Owing to these factors, open pit mining at great depth (300 to 1000 m) using shovel-truck systems faces some technical and economic problems. In-pit crushing-conveying (IPCC) systems have been known in the mining industry for many decades. The idea was introduced in 1956 in Germany. Today, the cost efficiency and high reliability of IPCC make it more appealing than conventional shovel-truck operation, especially in longer life projects with lengthy transportation distances and high production rates (Koehler, 2003). Since 1956, different aspects of this system have been reviewed by many researchers. Barua and Lanergan (1985) developed a computer program that compares the tonnage aspects of various conveyor layouts. They believed that to maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must first minimize the cost of the flatter slope, which is expressed in terms of additional stripping or tied-up ore. Dos Santos and Stanisic (1987) evaluated the design of a high-angle conveyor at the Majdanpek copper mine. Then, Sturgul (1987) applied GPSS (general purpose simulation system) to find the best location of an in-pit crusher."

Jan 1, 2017

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By K. Woodward, Y. Potvin, B. McFadyen, M. Grenon

Open stoping has become a popular mining method in hard rock mines, not only due to the safety of the method as a non-entry approach, but also because of the high extraction rate and low costs. At mine sites, stope performance is evaluated by calculating stope overbreak using the stability chart. However, limitations of the stability chart regarding the precision of the predictions, nonconsideration of factors such as the influence of blasting, and the exclusion of underbreak have led to non-optimal designs. The capabilities of today's computers have increased the amount of data being collected and the power of models being built. This article presents a step towards a new stope design approach where stope overbreak and underbreak are measured and georeferenced using octrees at an approximately cubic metre resolution and predicted using multivariate statistical models (partial least square, linear discriminant analysis, and random forest). Results show that overbreak and underbreak location along the design surface and their magnitude are predicted with good precision using a random forest model. These predictions are used to build the expected geometry of the open stope. The resolution of the data and the use of multivariate analysis has enabled the prediction of variation in stope performance along the design surface, going well beyond the simple qualitative per stope face prediction provided by a traditional stability chart approach.

Jun 5, 2023

By van der Merwem J. N.

"Coal pillars are prone to scaling over time, and are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces. Databases of failed and stable pillars cannot, therefore, be regarded as definitive.More than a decade has passed since the first attempt to predict the lifespan of pillars. This paper presents a review based on the new database and pillar strength equations. The methodology for the analysis is based on the fact that pillars scale. The ultimate safety factor (defined as the ratio between strength and load at the time of failure) is derived, followed by an estimate of the rate of pillar scaling, which results in an estimate of the expected time of failure.It is suggested that the predicted lifespan should not be used as an absolute indicator of expected pillar life, but rather as an index – the pillar life index (PLI) – to complement the safety factor and related probability of failure when evaluating pillar stability. A pillar with a predicted lifespan of less than 500 years would be regarded as being in danger of imminent collapse, while a lifespan of at least 1 000 years should be required for long-term purposes.The differences between this analysis and that published in 2003 constitute a strong case for regular reviews of all the empirically based stability indicators, namely the safety factor, probability of failure, and the PLI. Reviews at 10 year intervals appear to be required.The constants in the proposed method are valid only for the Witbank No. 1, 2 and 4 seams and the Highveld No. 2 and 4 seams.IntroductionIt is well known that over time, coal pillars are prone to scaling, and thus are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces and it is quite possible for failure to occur after a long time interval. In fact, scrutiny of the database of failed pillars indicates that failure occurred after periods ranging from 2 to 49 years, and not immediately after mining.The factor of safety for pillars at the time of failure is not the same as that immediately after mining. The concept of the safety factor is based on the pillar strength obtained by statistical analysis of pillar dimensions immediately, or within a month after mining, when the surveys are conducted. Strictly speaking, the safety factor as commonly used is valid only immediately after mining, and it continues to reduce thereafter. The ideal situation would be to base analyses of pillar strength on pillar dimensions at the time of failure, but that is simply not possible because the real dimensions cannot be measured at that time."

Jan 1, 2016

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody's economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible 'equivalent' support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987