Search Documents

[ ]

Jan 1, 1990

Jan 1, 1942

Jan 1, 1968

Jan 1, 1958

By C. E. Drennan

Your Chairman and the Program Committee have limited the time allotted to me, and so, with your permission, I will omit the preliminaries, and wade right into my subject. I believe I am safe in taking for granted that you are all agreed that electricity is the most feasible means of transmitting the power used in coal mining. If you are not, then the papers read before the Association in previous years have failed of their object. If you are so convinced, the only question is as to the choice between alternating and direct current, and the voltage. Fundamentally, this is primarily a matter of dollars and cents. With the sole exception of your trolley locomotives, there is no part of your equipment that cannot be operated as well on alternating as on direct current. With your pay rolls at their present high level and the efficiency of the labor you employ at the stage it now occupies, I believe you will agree, first, that everything possible must be done to increase the tons of coal produced per man employed; and, second, that ample power at all times must be available at every machine so that every one of your men can really get out a day's work without any avoidable delay. Speaking Electrically, all this means is a machine instead of a man wherever it is possible for a machine to do a man's work, and full voltage at the machine always, so that there can be no excuse for the work not being done promptly and efficiently-and dependably. The real reason for the selection of one kind of current or the other can best be understood by considering the formula which determines the size of wire required for transmitting electrical energy. The size of the copper required, and, consequently; its weight and cost, depends upon four factors: 1. The amount of energy or power to be transmitted. 2. The distance to be covered. 3. The percentage of loss allowed. 4. The voltage at the receiving end of the line. These factors enter into the problem to different extents, and, briefly, the size of wire depends directly upon the amount of power and the distance transmitted, and inversely upon the percentage of loss allowed and the square of the voltage. From this it will be seen that, with the amount of power and the distance fixed, if the loss is to be cut in two, the wire must be doubled with a given voltage, while if the loss remains constant and the voltage is doubled, the wire may be cut in four; that is, reduced 75 per cent in weight and cost. Now, standard motors are designed and recommended by their builders to run within a range of 10 per cent under voltage to 10 per cent above voltage - 440-volt motor, then, should preferably not be operated on less than 400 volts

Jan 1, 1923

By William Perry Pendley

Let us go back in time, back to when a Navy veteran from the South was President of the United States, a man from the Rocky Mountain West was Secretary of the Interior and a leading environmentalist was head of the EPA; and there followed what many perceived of as a war on the West-on our water, on our timber, on our oil and gas and mineral exploration, and on our small communities. It's easy to think that I'm talking about the administration of James Earl Carter, III of Georgia, but I'm not. I'm talking about this administration, the administration of George Herman Walker Bush of Texas. I say that as a life-long Republican who never voted for a Democrat and who worked hard to put George Bush in the Oval Office. Many of us wondered, in 1988, what Vice President George Bush meant when he said; "I am an environmentalist." Well, now we know. In his State of the Union address, which was otherwise lacking in specific detail, George Bush said two very specific

Jan 1, 1990

The Wednesday morning session was opened by President Stanley Shuhart at 9-30 a.m. He called the Chairman of the Auditing Committee. Kenneth Eaton, to report on the financial statement. Mr. Eaton read the data and asked for its approval. It was made, seconded and approved. John Turner, Chairman of the Resolutions Committee, submitted the following: RESOLVED: Whereas, in the year since the last convention of the Rocky Mountain Coal mining Institute, the Institute and the cool mining industry generally have suffered the loss through death of the services of: Walter M. Bellairs F. V. Colombo, M.D. George R. Delamater J. H. East, Jr. E. W. Felegy Hugo H. Machin Archie M. Morrison George E. Mills Veloy K. Piccioni

Jan 1, 1969

Jan 1, 1970

Jan 1, 1934

Jan 1, 1948

Jan 1, 1951

Jan 1, 1964

By Thomas Collier

MR. PRESIDENT AND CO-WORKERS IN THE COAL INDUSTRY: I was requested by our president to prepare a paper on Longwall Coal Mining, to be read before this honorable organization. There are three general systems of Longwall, Longwall advancing and Longwall retreating, and the Nottingham system which is worked in England and South Wales. In Fremont county, where I am employed, the Colorado Fuel and Iron Company are working their mines on the advancing system. The face is started generally from the bottom of the shaft or other mine opening, or, at the outside of the pillar left to support the shaft or slope-bottom and advances toward the boundary of coal area. As the roads in this system are maintained by pack walls, it is sometimes called gob-roads system, and by these means the mine is opened up rapidly and consequently early returns are secured from the capital invested. By this method, there is no expense for narrow work, and a minimum amount of timbering of the roads is required. Now what I call ideal Longwall work is where there is about eight inches of dirt mining-and four and one-half feet of coal, .and when the entries and rooms will gob themselves, so that there will be no rock or dirt to haul out to the surface. But this is not the case in the mine I am in charge of. The entries and rooms will not gob themselves, therefor we have to haul the rock and dirt to the surface, which runs up the cost of production. Now the ideal roof in Longwall is composed of tough elastic and pliable strata that yield gradually by bending when the coal is removed, and throwing a sufficient weight or roof pressure on the coal face to break the coal when the same has been mined or undercut. Timbering should be done systematically, the coal well spragged before the miner starts to undermine the coal. Cogs or cribs are alright in their place, but I am not a believer in crib in Longwall working because they are too strong for the roof and do not leave the roof to squeeze .down gradually and break the roof around the crib. Longwall work requires particular skill on the part of the miner, and a familiarity with the conditions affecting room and pillar work, and a good room and pillar mail may not be successful in. Longwall work. A good Longwall miner realizes more than any one else the importance of being regularly at his place every working day. A day lost causes his place to fall behind the others which makes his work harder, and his daily output is further reduced by the amount of small coal that is liable to result from the excessive pressure where the face falls behind. The bad results are also felt by the miner working on each side of such place, as the roof pressure is often insufficient and the coal does not break as well as when the face is kept in a uniform line.

Jan 1, 1921

Jan 1, 1948

Jan 1, 1973

Jan 1, 1923

By Parley Potter

GENTLEMEN OF THE COAL MINTING INSTITUTE: I was requested to write an article on mining a short time ago; however, the time has been so short that I have not had time to prepare an article as I would like to have presented it to this body. In writing this article it has not been my intention in making comparison of various mines, to favor one or discredit the other. I hope it will be considered in that light. The coal mining industry as I have seen it in the past, at present and in the future. In years gone by large tracts of coal land could be obtained at a very small cost, and as yet coal land may be purchased at a reasonable price in this country, but I believe the time is near at hand when the methods of mining will have to be changed greatly in this country. Many changes have taken place-in the last few years, some of them have been forced by law, others by the coal operators themselves, after being convinced that the changes made were for their own benefit. During my 20 years in the mines I have seen thousands and thousands of tons of coal lost that could have been saved if proper methods of mining had been used. The Room and Pillar system of mining coal is none. too good at its best ; a certain per cent of the coal is always lost, yet it is about the only system that can be used under certain conditions, but where the Longwall system can be used I believe it is the best system yet introduced. If the Longwall system is used' there is no coal lost. You get it all as you advance with the workings. Some coal operators object to the Longwall system for several reasons, and most of the reasons they advance are not founded on facts. For instance some of them claim it is too expensive. I will admit that the cost per ton is a little higher in Longwall than it is in Room and Pillar as a rule for the amount of coal' mined, but after the Room and Pillar mine is finished as a rule there are thousands of tons of good coal lost, for the simple reason that it cannot be mined at a profit. In many cases if the same mine had been operated on the Longwall system every ton of saleable coal could have been mined at a fair profit, and in the long run would have netted the owner much more money than it did under the Room and Pillar system. The Longwall system has been in operation many years in Europe and especially Great Britain, and is the most approved of systems in many countries at the present time. Millions of tons of coal have been saved by its use in those countries. It is claimed that the Armour Packing Company loses nothing but the squeal of the hog when it is killed, and doesn't allow it to squeal much. Why lose coal if the Longwall system of mining will save it? The Longwall mine is far more easy to ventilate than the Room and Pillar mine; the air has a much less distance to travel for the same amount of working face in Longwall than it has in the Room and Pillar.

Jan 1, 1921

[Addison, Herbert Big Horn Colleries Co., Colo. Bldg., Denver, Colo. Aleshire, N. C c-o Roberts & Schaefer Co., Wrigley Bldg., Chicago, Ill. Alexander, John Dacona, Colo. Allan, David Lafayette, Colo. Allen, John Ludlow, Colo. Allen, Thomas Box 420, Glenwood Springs, Colo. Alley, Gerald C. F. &I. Co., Pueblo, Colo. Allison, ArchieBox 562, Walsenburg, Colo. Allison, D. S 1331 Roberta St., Salt Lake City, Utah Allison, Park Engineer, Standard Coal Co., Standardville, Utah Allonier, Howard R c-o Lunkenheimer Co., Cincinnati, Ohio Ambler, J. B c-o Ambler & Riter, Kearns Bldg., Salt Lake City, Utah Anderson, A. E 403 Ideal Bldg., Denver, Colo. Andrews, Sam 503 Pike Ave., Canon City, Colo.. Angster, Joe Walsen, Colo. Angus, William B. W. Snodgrass, 1575 Lafayette St., Denver, Colo. Apperson, A. B Tramway Bldg., Denver, Colo. Armstrong, C. D Apperson Vallery Co., Tramway Bldg., Denver, Colo. Arnoldi,, Victor Ideal, Colo. Autrey, J. S Perrenaud Apts., Denver, Colo. Bachman, W. H 1601 Alcott St., Denver, Colo. Bailey, R. E Utah Power & Lt. Co., Kearns Bldg., Salt Lake City, Utah Baird, Elmer A Equitable Bldg., Denver, Colo. Bartlett, G. F 311 Ernest & Cranmer Bldg., Denver, Colo. Baxter, John M 3748 Lafayette St., Denver, Colo. Becker, J. A Box 682, Rock Springs, Wyo. Beebe, John. D 1414 Court Place, Denver, Colo. Bennett, F. C Colorado Fuel & Iron Co., Berwind, Colo. Benson, Geo Cumberland, Wyo. Betcher, B. L Standardville, Utah Beuchat, Charles Pryor, Colo. Bevan,John 1625 North Corona St., Colorado Springs, Colo. Bisch, James L Van Houten, N., M. Boissier, A. H. C Boston Bldg., Denver, Colo. Bottomley, Edward Kleenburn, Wyo. Bowen, James V Union Coal & Coke Co., Colorado Bldg., Denver, Colo. Bowie, Alex R Bowie, Colo. Bowie, John S Bowie, Colo. Bowie, Wallace D Bowie, Colo. Bowns, W. J Castle Gate, Utah Boyer, F. E 631Jackson St., Denver, Colo. Boyle, Chas Sweetwater, Wyo. Brandenburger, L 59 W. Broadway, Salt Lake City, Utah Brennan, W. D Dawson, N. M. Brewster, Burt B Walker Bank Bldg., Salt Lake City, Utah Brockman, A. L Sugarite, N. M. Brooks, Ed 513 Second St., No. 1 Hill, Rock Springs, Wyo. Brown, Geo. A Cumberland, Wyo. Brown, L. E :.1212 Walker Bldg., Salt Lake City, Utah Brown, Mark Y 629 East Main St., Trinidad, Colo. Bubb, H. H Cokedale, Colo. . Bullock, W. H 1052 Gas & Electric Bldg., Denver, Colo. Bunning, P. C Rock Springs, Wyo. Burnite, Thomas B 523 Boston Bldg., Denver, Colo. Butler, T. H Hanna, Wyo.]

Jan 1, 1924

The Wednesday morning session was called to order by President Geiger at 9:30 a.m. He asked Stan Shubart to conduct the meeting. Stan thanked Loren Linville and Bill Grant for the excellent job they did in their assignments. He called on John Schmidt, Chairman of the Auditing Committee, to report on the financial statement of the treasurer. Mr. Schmidt read the data and asked for its approval. A motion was made, seconded and approved. Stan called on Joseph Berta, Chairman of the Resolutions Committee, who submitted the following resolutions: (1) RESOLVED: Whereas, in the year since the last convention of the Rocky Mountain Coal Mining Institute, the Institute and the coal mining industry generally have suffered the loss through death of the services of: Clement Audin, Jr. C. Herbert Clendenin Donald Haske William H. Hays M. J. Keenan Fred W. Koelling James Mecca Neil Robinson C. M. Shott

Jan 1, 1974

Jan 1, 1947