Search Documents

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

[ ]

Jan 1, 2008

By Richard A. Dick

Underground blasting in permanently frozen gravel was studied in a 7-by 12-ft drift by running a nonreplicated 2 X 2 X 2 factorial experiment on the effects of type of cut, delay, and explosive on the fragmentation subsystem. Comparisons were made between a V-cut round and a burn-cut round, millisecond delays and half-second delays, and 40 percent special gelatin and 60 percent high-density ammonia dynamite. The number of large blocks in the muck pile) loading time, shuttle car operating time lost because of cleanup needs, length of advance per round, and length of muck pile were recorded and statistically analyzed. None of the blast parameters had a significant effect on the length of advance or length of muck pile, although the half-second delays tended to give a shorter muck pile than millisecond delays. The burn cut required less secondary breakage, less loading and cleanup time, and gave better overall fragmentation than the V-cut. The ammonia dynamite shots required less secondary breakage and less loading time than those using special gelatin. The half-second delays gave better overall fragmentation and required less cleanup time, but the millisecond delays gave a better loading rate. None of the differences between delays and explosives were notably significant.

Jan 1, 1970

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 1, 1976

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974

By N. E. Hanna

An investigation was made of pressure pulses produced by unconfined explosive blasts in underground openings. Four tests were made with TNT or modified amatol charges ranging in weight from 60 to 2,000 pounds; each test involved either single or multiple charges. Pressure-time profiles were obtained using mechanical self-recording pressure gages. The cube-root scaling law for peak pressure was found to be valid within about 1 tunnel diameter; at greater distances, the pressures obtained along direct paths were generally higher than this scaling law would indicate.

Jan 1, 1968

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covers 54 brands of gasoline represented by 1,480 samples plus those from the Pacific Coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Several changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas and western Tennessee. The Rocky Mountain areas have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico, and El Paso, Tex., have been combined to represent the South Rocky Mountain district. The Cleveland district has been expanded to include Ohio an,"- Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippi, and northern Florida.

Jan 1, 1938

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and materials.

Jan 1, 1978

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1990. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1991

By R. Ward Stahl

Fire is still a scourge of the mining industry, although many precautionary measures have been and are being taken to reduce the incidence of fires and to combat them. Generally, the success of fire extinguishment is directly proportional to the speed of attack, and the speed of attack in turn is dependent upon the availability of materials and trained personnel. Preparations for firefighting are frequently neglected because they are considered emergency needs and do not contribute directly to coal production. Fire incites panic--a fact often overlooked--but such chaos can be minimized by training people in the use of equipment and procedures. Heat, smoke, and fumes hamper the approach to a fire; however, a relatively new technique of attacking fires with high-expansion foam may well contribute greatly to firefighting. The foam is transported to a fire and used at a considerable distance, thus permitting the firefighters to work more safely.

Jan 1, 1962