Search Documents

By Mark S. Stagg, Virgil J. Stachura, John W. Kopp, David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air- blast levels and measurement methods are equivalent in terms of structure response, and any one could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must be used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to pre- clude damage to residential structures and any possible human injury over the long term.

Jan 1, 1965

By M. M. Tilman

A series of alloys was laboratory prepared by adding up to 4 weight-percent cobalt to the basic composition of type AM 350 (AISI 633) stainless steel. Aging curves were established for each alloy at 750° F, 850° F, and 950° F for lengths of time up to 100 hours. A series of annealed steels containing as much as 1 weight-percent cobalt was cold-rolled 50 percent and aged for 3 hours at 850° F. No improvement in hardness due to cobalt was observed in the steels transformed by heat treatment. Slight improvements in hardness were observed in the steels transformed by cold working.

Jan 1, 1968

By Howard M. Stainer

Jan 1, 1963

By Howard M. Stainer

[Cover Page]

Jan 1, 1963

By John G. Kovac

A computer simulation has been developed by the US. Bureau of Mines to estimate the chances of a miner making a successful escape while wearing a self-contained self-rescuer (SCSR). The model takes into account (1) training in the use of SCSR's, (2) apparatus integrity, and (3) oxygen cost of a mine escape. This report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By J. A. Zimrner, R. J. Tirnko

The roles of main mine fans in underground mines are to induce airflow and continuously re- move hazardous gases and dust. While most larger mines use multiple fans to accomplish these tasks, many smaller mines employ only a single fan. This paper concentrates on those mines having only one fan to provide ventilation needs. If this fan should cease to function, it is likely that methane concentrations will in- crease in some areas of the mine. As a safety precaution, Federal Regulations require that personnel must be- gin evacuating the mine within fifteen minutes after fan stoppage. Powered haulage can be used to transport workers to the mine portal as long as travel is through areas where hazardous levels of methane are not expected. To determine where methane will accumulate along haulageways during a fan stoppage, air samples must be taken at specific areas and analyzed for hazardous gases. During this study, procedures were developed for measuring methane levels along the haulegeways that are used to exit a mine following stoppage of the main mine fan. Methane levels were measured in four different mines at selected underground locations during four planned fan stoppages. In these mines the measurements taken only at the specified locations showed that, if workers had used electrically powered haulage to exit the mine following a fan stoppage, the methane accumulated along haulageways during fan stoppages would not have significantly increased the risk of an ignition.

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By H. W. Gillett

This bulletin is issued by the Bureau of Mines as a contribution to the increase of safety and efficiency in the preparation and utilization of the mineral resources in the United States. Notable among the drains on these resources are the demands made by the nonferrous- metal industries, and in these the losses occasioned in melting brass and bronze are worthy of particular attention. This statement will be better appreciated by a consideration of the size of the brass industry.

Jan 1, 1914

By Isaac A. Zlochower

A number of ignition incidents involving mining and farm equipment have illustrated the surprising danger of drilling, cutting, or otherwise penetrating sealed compartments or frames that are filled with metal scrap for ballast. The presence of chemically-reactive metals (or electrochemically-active pairs), such as zinc in galvanized steel, can produce hydrogen from moisture in the steel scrap, and the resulting pressure, due to the internally-generated hydrogen, can produce an easily-ignited gas jet when the sealed component is penetrated.

By John C. Machisak

THE INJURY data and related employment experience of the coking industry in the United States for 1955 arc presented in this publication under the following general sections: (A) General Injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, injury-frequency rates, and accident agencies involved in causing injuries. Data are tabulated for the industry as a whole, for each typo of oven: and for the States in which coke is produced.

Jan 1, 1958

By Steven J. Page, John A. Organiscak

Airborne dust generation is one of the byproducts of coal mining, processing, and handling. The amount of airborne total dust (ATD, respirable size and larger) and airborne respirable dust (ARD) generated is of primary interest for designing the level of engineering controls needed for adequate dust abatement. Laboratory crushing experiments were conducted in a wind tunnel with a roll crusher to identify relationships among crushing parameters, product size, coal rank properties, and airborne dust generation. Through the first series of experiments, the effect of primary and secondary breakage processes on both product size and airborne dust generation was examined. Through a second series of experiments, the effect of coal rank properties on product size and airborne dust generation was studied using a uniform crushing process with secondary breakage. Laboratory results indicate that secondary breakage of a particular coal notably increases the specific amount of ATD generated, while negligibly impacting the specific amount of ARD generated. A strong positive relationship was identified between the specific amounts of ATD and ARD generated during the primary breakage process (with minimal secondary breakage), but a negligible relationship was observed between the same two variables when secondary breakage was introduced into the crushing process. This indicates that most of the ATD and ARD is generated from the primary breakage, while secondary breakage has a more of an influence on generating additional amounts of larger sized ATD. Additional experiments involving the uniform crushing of eight different bituminous coals showed that the coal rank, expressed as the inherent moist fuel ratio (MFR = fixed carbon =(volatile x inherent moisture)), had diverse relationships between the product size created and the amount of airborne dust generated. As bituminous coal rank or MFR increased, the amount of coal product fines < 250 gm increased while the mass percentage of ATD and ARD liberated from these < 250 µm product fines decreased. Air dry loss (ADL) moisture in the coal was found to be inversely related to the dust cloud electrostatic field, influencing dust liberation from the coal product fines. Since the MFR was directly related to the dust cloud electrostatic field, opposite the ADL-electrostatic field relationship, the diverse relationships between the product size created and the amount of dust liberated from the < 250 µm product fines were explained. Finally, 12 to 14 times more ATD was generated as compared to the ARD generated during these experiments. These results should provide a fundamental basis for initial estimation of the airborne dust loading requirements of engineering control methods for coal crushing.

By F. E. Cash

"In the interest of accident prevention it is felt that a report of the measures taken during the past four years toward the reduction of fatal accidents in Alabama, especially in preventing falls of roof and coal, will be of interest throughout the mining districts.In order to determine the primary factors in the reduction of fatal accidents from falls of roof and coal, the operators, State Inspection Department, and the Alabama council of the Holmes Safety Association were asked: ""What has your organization done to help in the reduction of accidents from fails of roof and coal?"" The responses to this question have made this report possible.To bring out briefly the reduction in fatal accidents from falls of roof and coal as well as from all causes, the following three tables have been prepared.These statistics have been compiled from the records of the State Inspection Department.In the order mentioned, it is felt that credit for the reduction in fatal accidents from falls of roof and coal should be given to the individual operating companies, the State Inspection Department, the Alabama council and chapters of the Holmes Safety Association, and the Alabama Mining Institute. The individual operating companies naturally head the list in that they are directly concerned from a humanitarian as well as a financial point of view. The State Inspection Department through frequent and thorough inspections and by providing necessary statistics is largely responsible for the reduction. The Alabama council and its affiliated chapters of the Joseph A. Holmes Safety Association through its publicity and education reaches a large number of employees throughout the mining district. The Alabama Mining Institute defrays the council expenses and thus makes possible much of this service to the Alabama mining industry.In 1925 there were 49 fatalities, equivalent to 115,169 man days per fatality, from falls of roof and coal, which was by no means a good record; in 1926 the number and frequency of accidents were reduced to 42 fatalities and 149,096 man days per fatality. When in 1927 the fatalities from this cause mounted to 61 and the man days per fatality were reduced to 89,903, it was quickly realized that more concentrated efforts must be exerted to reduce such accidents.As early as August, 1927, at which time the fatalities from falls had reached a total of 31, the following letter from the Chief Mine Inspector was written to each operating company in the State and was the initiation of a very strenuous campaign by all parties concerned towards the reduction of accidents from falls of roof and coal."

Nov 1, 1929

By Andrew B. Cecala

While various types of equipment are used in bulk material processing plants to control respirable dust, the equipment often doesn&apos;t adequately protect workers. One cost-effective way to supplement your existing dust control equipment is to install a whole-plant ventilation system. This article outlines research by the National Institute of Occupational Safety and Health (NIOSH) on using whole-plant ventilation in two mineral processing operations to reduce respirable dust levels. Information also covers how to design a ventilation system for any bulk material processing plant.

The optimum situation in sealing the soil with latex would be to locate the sealant at the depth where natural permeability is lowest, and to narrow distribution of the latex to a film. To ascertain how closely we were achieving these objectives it was necessary to devise a method to measure the concentration of latex in soil. A number of methods were explored and two were used in actual field tests. SBR latex tagged with c14 was prepared and used to determine the distribution of polymer in the soil. The latex was made by copolymerizing a mixture of radioactive and normal styrene with butadiene in bottles by conventional methods. Average particle size was 600 Å. Diluted aliquots had 1.40 microcuries radioactivity per gram of latex. Tagged latex was mixed with soil in a range of proportions from 0.01 to 0.25% by weight to develop a calibration curve. Analyses of soil in the laboratory and from the field were determined by comparison with this master curve. Styrene-containing polymers have a characteristic peak at 700 cm-1 but crosslinked SBR is not soluble in solvents normally used in infra-red spectroscopy, e.g., carbon disulfide. We developed a method for solubilizing the crosslinked polymer by stirring overnight at room temperature a soil sample in chloroform with t-butyl hydroperoxide and osmium tetroxide. The filtered chloroform residue was dried to constant weight, thoroughly mixed and pressed into a KBr pellet, and concentration was determined by measuring the absorption at 700 cm-1. Details are given in an Appendix.

Jan 1, 1972

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By Hans M. Cassel

The specific objective of research presented in this report was clarifi- cation of physicochemical fundamentals of the mechanism of dust explosions. The equipment, techniques (chiefly photographic), and dusts (chiefly graphite and light metals) employed are described. From behavior of individual par- ticles, conclusions are drawn as to their cooperative function in ignition and combustion of dust clouds. Results are interpreted using thermal theory as accepted for combustible gas mixtures. Radiative transfer across the flame front, as a characteristic of dust flames, is given particular atten- tion. Related studies by other investigators are discussed.

Jan 1, 1964

By K. L. Kreamalmyer, A. B. Neeham

The Alice mine is one of several zinc deposits in Ozark and Howell Counties, Missouri. It was selected as the first to be investigated by the Bureau of Mines in an effort to demonstrate reserves of sulfide ore under the shallow carbonate ores from which all production of the district had come up to World War II. The property was worked first about 1890 and was most productive prior to 1900. Its output was the bulk of the district’s total up to 1940, which is believed to have been about 85,000 tons of washed and sorted ore carrying 17 to 36 percent zinc. The firm of Doane & Ives owned and operated the Alice on a scale of a few to 25 tons a day from 1940 to 1946. An open pit about 300 feet long, 250 feet wide, and 30 to 50 feet deep comprises the mine working. Numerous old drifts and shafts in the walls and bottom of the pit are now inaccessible. The ore consists of zinc and iron minerals replacing and filling openings in dolomite. Sulfides are absent or scarce to a depth of 40 to 50 feet; smithsonite was the chief ore mineral in the oxidized zone. The individual ore bodies are irregular in size, shape, and zinc content, and “horses” of waste occur within the pit. The Bureau of Mines recommended churn drilling to test the depth, extent, and richness of the zinc sulfide ore. Four holes were drilled by a private company and seven by the Bureau in and around the pit; several penetrated considerable thicknesses of material containing a few to 10 percent (metallic) zinc in the form of sphalerite.

May 1, 1947

By Joseph A. DeCarlo

This information circular presents data for 1960 on individual coke plants in the United States. All oven-coke plants in existence, whether active or idle at the close of the year, are listed in this report. With two exceptions, only beehive plants on which reports were submitted to the Bureau of Mines are included. Although the Bureau was unable to obtain reports from these two active plants in 1960, the number of ovens and annual coke capacity are estimates, based on previous reports filed with the Bureau of Mines. Accordingly, there were 73 oven-coke plants in existence at the end of 1960 of which 70 were active. Reports were received on 44 beehive plants of which only 13 were in operation at year end. Oven-coke plants are listed alphabetically by States in table 1 which shows the name and address of the company, location of plant, classification or type of ownership, number and type of ovens, annual coke capacity, and coal-chemical materials produced. The terms "furnace" and "merchant" plants used in this and all other reports of the Bureau of Mines designate the type of ownership. Furnace plants are those owned by iron and steel companies whose main business is production of coke for use in their own blast furnaces. Merchant plants are those associated with chemical companies, gas utilities, as well as those that produce for sale on the open market metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials. The annual coke capacity shown for each plant in this table is based on the minimum coking time necessary to produce coke with qualities suitable for its intended use. Therefore, the annual capacity of a plant may change from year to year, depending on age and condition of ovens, the character and quality of coal carbonized, the grade of coke required, and other factors. For example, annual coke capacity of a coke plant primarily making foundry coke with longer coking cycles would be lower than one making blast-furnace coke. Also some ovens must be operated at slightly lower than normal flue temperature because of the condition of the refractories and maximum capacity would be somewhat lower than designed capacity. For this reason, the capacity reported to the Bureau of Mines may differ from the designed or rated capacity estimated by the coke-oven builders at the time of construction. For example, if the generally accepted standard coking rate of one inch per hour were used on all ovens to calculate total annual capacity, it would have been 80.4 million tons or 2 percent higher than the capacity reported to the Bureau. Because of the factors mentioned above, the annual coke capacity shown in this table is believed to be a reliable measure of the practical operating capacity of the industry.

Jan 1, 1961

By H. J. Van der Veer, F. E. Griffith

"Reflector button signs similar to those used to attract the attention of motorists on the public highways at night are now being used to good advantage by a few mining companies in underground workings for danger, warning, direction, and safety signs and signals. Most safety signs and signals used in underground mining are of the electric light painted-board, or enameled or porcelain metal-plate,type, all of which have good features as well as some disadvantages; among the disadvantages are: The filament of electric incandescent lamps is prone to ""burn out"" occasionally anti usually the lamps are not replaced promptly; painted-board and enameled or porcelain metal-plate signs can be seen only a short distance and often are ""passed up"" unintentionally by employees, consequently these signs do not always serve the purposes intended and may be the cause of injury or death through failure to warn the men of danger.The advantage of using reflector button signs in mines or underground workings is that the cap lamps or headlights with which employees and locomotives generally are equipped, if directed at these buttons will reflect the light back to its source, and if they are arranged to spell words of warning or direction, or if suitable symbols are used, they are discernible and can be read at a distance of several hundred feet. The distance the light is reflected depends largely on the color of the buttons used. The reflector buttons also in many instances can be used to good advantage in conjunction with other methods previously mentioned.Several types of reflector buttons are available, among them the flat-lens type with mirrored metallic foil or plate back, the facet-cut-lens type with a mirrored metallic foil or plate back, and a type with a hemispherical smooth lens with a parabolic mirrored metal back. Lenses for the different types are available in several colors. Crystal, amber, red, and green are the colors of the buttons used to the greatest extent in underground signs up to the present time. These buttons may be had in different sizes, also.It has been observed that crystal-colored buttons reflect light the greatest distance (about 1,000 feet) and red-colored buttons the least (about 500 feet); reflection from green and amber colors ranges somewhere between the red and crystal colors in distance.Reflector buttons for underground use should be designed to reflect light a maximum distance; they should be made of materials that resist oxidation and corrosion, especially of the mirrored backs, and should be relatively free of protruding parts or projections that will collect dust.Reflector buttons approximately 3/14 inch in diameter seem best suited for underground use in general because fewer reflector units are required for a signal of given size."

Dec 1, 1937

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection system, the US Bureau of Miner is actively in involved in developing a coal rib-thickness monitoring system for highwall mining applications. One particular system that shows promise in a ground-pentetrating radar system to detect the coal-air boundaries of coal rifts. Based on preliminary laboratory and field tests results indicate that this method can be applied successfully in highwall mines to maintain constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.