Search Documents

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

By Margaret R. Egan

In an underground mine fire, a toxic mixture of combustion product gases and particulate matter is transported by the ventilating system endangering everyone downstream. To determine the magnitude of the problem that these toxic combustion products pose, the U.S. Bureau of Mines is investigating the combustion products of typical materials found in underground mines. The total toxicity of the combustion products depends upon the evolving gas species and particulate matter, the amount of material involved, and the ventilation rate. In a simulated mine environment, the products from smoldering poly- vinyl chloride (PVC) brattice and conveyor belting were analyzed for gas concentrations and smoke characteristics. The primary toxic gases are hydrogen chloride (HC1) and carbon monoxide (CO). Smoldering conveyor belts are more detectable than smoldering PVC brattice cloths. These results, combined with previous analyses, are used to estimate relative toxicities, product levels, and detect-ability of smoldering mine combustibles.

Jan 1, 1992

By Dennis Cox, Stephen P. Signer, Joanne Johnston

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to (1) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

In Maryland, coal mining is confined to Garrett County and the western portion of Allegany .County. Terrain in both counties is predominately level with rolling hills; state law prohibits surface mining in steep slope areas. The Conemaugh and Allegany geologic formations contain five major minable fields or basins. These include: Upper Youghiogheny, Lower Youghiogheny, Castleman, Upper Potomac, and Georges Creek. Maryland's coal reserves are estimated to exceed one billion tons. Approximately 490 million tons of bituminous coal are considered recoverable using conventional mining methods. After World War 11, deep mining declined in Maryland, and by 1977 surface mining accounted for 91 percent of the total production. Since then, production at underground mines has recovered, accounting for 69 percent of the coal production in 1991. Maryland's permanent regulatory program was fully approved February 18, 1982. Its Abandoned Mine Land Program was approved June 16,1982.

Jan 1, 1992

To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs.

Jan 1, 2001

Develop a curved ray geotomographic program with constraints to counteract non-uniqueness in order to improve the reliability of seismic tomographic imaging of geological structure in mining regions. Background Seismic tomography provides a two-dimensional image (tomographic reconstruction) of the distribution of the seismic velocity in geologic structures using measured travel times of seismic waves crossing the area. It can provide a more complete representation of features be¬tween boreholes than other crosshole processing methods that measure only average properties or borehole logging methods that measure properties only near each borehole. Seismic tomography has many mining applications. They include locating geologic structures of contrasting seismic velocity, detecting fractured regions where the seismic velocity is low, and monitoring solution injected above the water table where the increase in saturation increases the seismic velocity. Thus, tomographic imaging techniques show great promise for detecting and locating geologic hazards that affect the productivity, safety, and environment of mining operations.

Jan 1, 1992

By Bob Thomas, Syd Peng, Quanzhong Gu, Gene Wilson, Gerald L. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of :he rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock layers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified. In order to determine the application of the drilling parameters for identifying roof rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble, and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation on the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

To provide a means for rapidly evaluating proposed mine layouts in order to avoid potential hazards while minimizing loss of coal. The Approach: Development of a computer program that will compute many possible mine layouts by changing the mine plan until the arrangement giving minimal hazards with optimum extraction is found. How It Works: The Hazard Evasion Program for Mine Planning, developed by the Bureau's Denver (Colo.) Mining Research Center, tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on the criteria of maximum safety for workers with minimum abandoned coal), limits the number of choices that need to be considered and appraised for applicability to a given mine scheme. The program is applicable for room and pillar or longwall mining, for oil and gas well hazards, and for other hazards that can be described mathematically such as channel sands, potential bad roof areas, faulting, voids, or water pockets.

Jan 1, 1974

The dust exposure of the longwall shearer operator is usually determined by his position relative to the cutting drums. The dust generated during cutting may travel up-wind, against the primary airflow, and be carried out into the walkway where it can contaminate the intake air for as much as 10 feet outby the shearer operator's controls. Thus, both head and tail drum operators are exposed to un-acceptably high levels of air-borne respirable dust. One Solution The latest generation of long-wall shearers has features that make the use of radio remote or umbilical (hard wire) remote control relatively easy to implement. Remote control can enable shearer operators to control machines from positions that are less dusty than normal control stations. With either type, the head-drum operator can now control the shearer from a position up to 20 feet on the intake-air side of the shearer, while the tail-drum operator's station is now located across from the head drum.

Jan 1, 1984

By L. C. IlsLey

A preliminary investigation has recently been made by the U. S. Bureau of Mines to determine whether or not the ordinary mine- type telephone is entirely safe in gaseous atmospheres . Two well known makes of mine- type phones were purchased for this investigation . It is not conceivable that the current necessary for talking over telephones could ignite gas . However , such phones are provided with efficient magnetos , and it was believed that danger might result from the ringing of the magneto . Again , while this type of phone has been designed to have a certain measure of dust and moisture tightness , evidently it has not been designed as an explosion- proof device . either with regard to cover joints and fastenings or strength of castings . Therefore , the problem was simplified . First it was assumed that owing to the construction of the telephones the gas would penetrate into their interior , and the question was to ascertain whether or not the gas would be ignited from the operation of the magneto .

Jan 1, 1922

By I. W. ROBERTSON, G. G. Oberfell, G. A. Burrell

The Bureau of Mines, in pursuing investigations looking to greater safety in mining, has analyzed samples of the air in many different coal mines in the United States, and has studied the analyses. This report presents the results of one phase of this study and shows how atmospheric air, after entering a coal mine, loses oxygen and gains carbon dioxide with resulting formation of so-called black damp. Also the report discusses the effects of the constituents of black damp on men, on the burning of oil and acetylene lamps, and on the ex- plosibility of methane. The term "black damp" was and still is widely used to designate accumulations of carbon dioxide, but a more exact definition of black damp, as Haldane, the English physiologist, has pointed out, is an accumulation of carbon dioxide and nitrogen in proportions larger than those found in atmospheric air. The reasons for preferring Hal- dane's definition are given on succeeding pages.

Jan 1, 1916

By G. H. Schnakenberg

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaust-control, technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

By Chelesa C. Woodward, Gregory G. Miller, Walter K. Utt, Wayne L. Howie

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the use of a drill monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof so that roof drill operators can be warned when a weak layer is being drilled. Measurements taken during drilling can be converted to suitably scaled features so that a neural network can classify mine roof strata in terms of relative strength. The feasibility of this concept has been demonstrated in the laboratory. The research project was undertaken in order to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills used in underground mining and would likely find wider application as well.

Jan 1, 2002

Through 1986, Kentucky was the nation's largest coal producer. Currently it ranks third in production, behind Wyoming and West Virginia. Because of the size and variety of Kentucky's coal industry, virtually every kind of surface coal mining and reclamation activity takes place in the state. Extensive coal deposits occur in two separate areas: the eastern coal field, which is part of the Appalachian coal field, and the western coal field. Kentucky's reserves are estimated at 65 billion tons, with 27 billion tons in eastern Kentucky and 38 billion tons in western Kentucky. Kentucky coal is high in volatile matter, low in sulfur and ash, and relatively high in heating value. Coal from Kentucky's eastern coal fields contains a sulfur content of less than 1 percent. Conditional primacy was granted to Kentucky May 18,1982. Since then, all conditions have been removed; final regulatory approval was granted on May 30,1985. The Abandoned Mine Land Program was approved with the regulatory program May 18, 1982.

Jan 1, 1992

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

Coal-bearing beds underlie 23,000 square miles, about one third of Missouri's total area. Twelve out of more than twenty named coal seams have been or are being commercially mined. The remainder are too thin for commercial production. The coal is high volatile bituminous, with reserves estimated to be six billion tons, 1.24percent of U.S. coal reserves. Coal-bearing strata are generally thin seams which can be up to five feet thick. Typically, mined seams are about 28 inches thick. Coal deposits were first mined in Missouri in the 1840s, with the coal used primarily for domestic heating and blacksmithing. Production increased with the introduction of steamboats on the Mississippi. Coal production in 19 17 was six million tons. Production has steadily declined from a high of nearly seven million tons in 1984 to 2.3 million tons in 1991. Declining production is the result of several factors, including competition from other energy sources and the high sulfur content of Missouri coal. Today, coal-fired electric generating plants are the biggest consumers of Missouri coal. The Missouri regulatory program was conditionally approved November 21,1980, and fully approved January 17,1983. Its Abandoned Mine Land program was approved January 29, 1982.

Jan 1, 1992

By Charles Vaught, Michael J. Brnich, Henry P. Cole, John V. Haley, William J. Wiehagen

Forty-eight workers who bad escaped large underground coal-mine fires were interviewed using an open-ended protocol. This information, and the actual experiences of one eight-person mine-section crew who escaped from a Fire, were used to construct an 18-frame (page) table-top simulation exercise, which was then field tested with 134 miners. The exercise is a research toot that measures miners' proficiency in the information-gathering and decision-making skills related to escaping from a mine fire. It also helps miners to learn and practice these cognitive skills. The exercise was found to be valid and reliable. All miners reported that the exercise was authentic and would help them to remember important information. The exercise total score, and all but two item scores, significantly discriminated among miners with different levels of training. The two items that did not discriminate dealt with whether or not to abandon a helpless fellow miner. When the exercise total score data were pooled, only 13.6% of the miners achieved a desirable score of 90% mastery or greater. The simulation is important because it teaches and assesses critical judgment and derision-making skills that are rarely addressed in miner training. Index Terms- Coal mining, critical skills, decision making, emergency escape and evacuation, escape from fire judgment training, mining, safety training, simulation training, under-ground mine fires.

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours. Tests showed that the wood boxes protected the detonators for over an hour with variations between the different trials. In the IME 22 container tests, detonators began exploding in as little as 17 minutes in one test and not for 2-/12 hours in another test. Detonators in the metal/plywood boxes began to explode in about 15 minutes but with minor alterations, were able to contain the detonators. The test results show that the exterior of an IME 22 container significantly affects its thermal properties. Defects in the form of cracks and the manner in which the container is closed have a significant effect on the performance of a detonator container in a fire.

By Scott Turner

To be successful , human exertion employed for the creation of value requires power and heat ; the ability to produce concentrated power in great quantities has resulted in the relatively recent industrial development that is so profoundly affecting the world . In our commercial history , we have advanced through several stages in the selection of the most suitable fuels , continuously striving to increase the flexibility and range of energy- transmission . The easy distribution of light , power and heat is the leading factor in the decentralization of industry which promises to correct some of the serious evils that have followed in the footsteps of our commercial development . The distribution of fuel in quantity in so convenient a form and with such an attractive reliability- factor as can be had with gas , meets the modern conception of efficient service . Natural gas has been used in this country for more than a century, but recently it has attained a prominence far in excess of anything known in its earlier history. We may consider that we are now getting into our real stride in the utilization of our natural- gas resources . : In a country like the United States , wherein we are accustomed to mammoth achievements , we may be inclined to accept casually the noteworthy technical and economic advances which have resulted in the expansion of natural- gas distribution . About three years ago , the transmission of natural gas a distance of more than 250 miles from its source was first accomplished , and this was really a noteworthy engineering feat . Today , this useful commodity is being transported twice that distance , and lines are being laid which will carry gas more than 900 miles from the points of occurrence . Let us not take such outstanding improvements too much as a matter of course ; the industry should be congratulated on its long steps forward .

Oct 1, 1930

By Oliver Bowles

"Waste Granite in the Barre, Vermont, District: Waste in the great granite center at Barre, Vermont, consists of three types of material, the rough blocks rejected at the quarries on account of imperfections, the chips or spalls resulting from trimming and dressing at the cutting plants, and the granular and pulverized material from the dust collectors. The waste piles at the quarries of are immense proportions and constitute a serious handicap to quarrying in that they cover up good rock deposits, and are also so large that waste disposal becomes more and more expensive. The problem of utilization of such waste material is a topic of keen interest to all granite producers.Barre is not situated on a water route, and thus transportation costs prohibit the shipment of waste blocks for rip rap or ballast. Crushing plants use a small amount of this material for road construction, but aside from this, the waste is practically valueless.Investigators of waste utilization problems are awaiting with interest further information concerning an enterprise undertaken at Montpelier, Vermont, to utilize crushed granite for the production of brick similar to sand-lime brick. Granules of granite are mixed with lime, moulded, and hardened under steam Pressure, The brick produced are said to be of excellent quality for structural Purposes.There seems to be no logical reason why waste granite could not be utilized for the manufacture of building stone, and paving blocks, for many of the defects which condemn a stone for monumental purposes are not at all detrimental for building or street paving. F or the most part, monumental stone workers are not particularly interested in other branches of the granite in-dustry, and a combination of industries such as that suggested"

Jan 1, 1920