Search Documents

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

By P. Kovalchik, S. Peng, G. Cole, R. Matetic

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90 percent of coal miners and 49 percent of metal/nonmetal miners had a hearing impairment by age 50 (Franks, 1997). Mine workers are exposed to additional noise levels underground due to the reflection of machine-generated noise that would otherwise dissipate in an aboveground setting. Determining the sound-absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed rather than being reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes a finite room, a diffuse field and a relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper presents a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients are essential for determining and predicting potential overexposure to machine operators in different mine environments.1

"The dust/lung research of the Center has several long-range objectives:* better methods for the early diagnosis of coal workers' pneumoconiosis (CWP);* methods to modify the disease process;* tests to identify toxic products; and* tests to identify individuals with heightened susceptibility to pneumoconiosis.A major immediate objective is to define the mechanism of dust-induced lung disease. This means determining:* dust characteristics that are important in causing lung diseases;* important interactions between dust and lungs; and* earliest detectable stages of the disease.Several of the Center's projects involve exposing lung cells in culture (in vitro) or animal lungs (in vivo) to samples of the suite of characterized mineral dusts described earlier. The responses of the lung cells or tissues to the dusts are being studied in order to better understand how inhaled dusts cause lung disease.One project is studying the effect of dust exposure on the production of mucus by rat tracheal explants in vitro. Mucus is a major factor in clearing inorganic dusts from the lung. Results thus far have shown that exposure of tracheal cultures to coal dust caused a decrease in micin production in comparison to parallel cultures without dust. To examine the effect of in vivo coal dust exposure, rats were maintained in an inhalation chamber for two weeks, and control rats were in an identical, but dust-free chamber. Tracheal explants results indicate that the effect of in vivo dust exposure is similar to that noted in the in vitro experiments.Pulmonary alveolar macrophages (PAMs) are a key component of the lung's response to inhaled particulates, and they play several important roles in pulmonary inflammatory and repair processes. PAMs are the cells that actually ingest dust particles. Other studies have shown that they play a critical role in the development of silicosis and asbestosis. The Center is studying the effect of dust exposure on the release of oxygen free radicals (superoxide) by PAMs. Intercellular production of superoxide occurs when PAMs phagocytize particles, such as inhaled bacteria, and is an essential mechanism by which PAMs kill ingested, bacteria. A number of complex physiological events occur during this process which are not clearly understood. It is thought that PAMs containing indigestible materials, such as mineral dusts, overproduce superoxide, or inappropriately release it into the surrounding tissues. If true, this would cause toxicity to surrounding lung cells by peroxidation of the lipids in the cell membranes. In vitro exposure of PAMs to low or high doses of kaolin is inert. Preliminary studies indicate that coating the quartz particles with a surfactant reduces toxicity."

Nov 1, 1988

Improve the dust-control effectiveness of the Rotoclone1 dry-dust collection systems used on surface coal mine drills.

Jan 1, 1994

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

Improve the efficiency of stainless steel pickling (chemically cleaning) operations by providing the industry a quick and convenient method to estimate pickling solution behavior and to estimate recommended ranges of nitric and hydrofluoric acid concentrations for effective pickling of stainless steels. Background Iron, chromium, and nickel in stainless steels react with nitric and hydrofluoric acids during pickling. Ions of these dissolved metals complex or combine with the acid anions. When the total metal concentration reaches about, 50 grams per liter of pickling solution, the solution no longer serves its purpose and is considered spent. Knowledge of cation and anion species in these pickling solutions contributes an insight into pickling chemistry and allows estimates to be made of the most effective ranges of acid concentrations. The Bureau developed a computational model of the complex equilibrium chemistry occurring among iron, chromium, and nickel and the pickling solution. Total concentrations, in grams per liter, of nitrate, fluoride, iron, chromium, and nickel were used as input; output was 17 cation and anion molar concentrations. The model, in the form (if an equilibrium program on a mainframe computer, was used extensively to facilitate Bureau research by determining chemical complexes in numerous stainless steel pickling solutions. However, the program's availability to members of the stainless steel industry, its intended users, was limited because of lack of mainframe compatibility and the difficulty of program maintenance.

Jan 1, 1989

By John C. Edwards

A computer code for laminar, steady-state, incompressible, two-dimensional flow developed by Gosman (2)3 was modified by the Bureau of Mines to calculate shock (minor) loss at the intersections of ventilation ducts. Turbulent flow was simulated using laminar flow equations and an appropriate wall shear stress. Results of the calculation showed good agreement with the experiment.

Jan 1, 1977

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

By S. Gallagher

If we consider ergonomics to be an exercise in matching job demands to worker capabilities, one of the principal capabilities we must be concerned with is that of human strength. Our ability to evaluate different characteristics of muscular strength has increased dramatically over the past couple of decades with the development of new and increasingly sophisticated instrumentation. One would think that armed with such advanced techniques, we might be able to develop methods to conclusively identify workers at risk of injury in physically demanding jobs. Unfortunately, this has not yet proven to be the case. Instead, what these instruments have continued to point out is how intricate a function muscular strength really is, and how complicated and ambiguous its relationship is to musculoskeletal injury. While we cannot just use isolated tests of strength to specify precisely who may be at risk of injury, studies have indicated that strength testing can be a useful tool for job design and, under certain circumstances, selection of workers for demanding jobs. However, because strength is such a complex phenomenon, there has often been some confusion regarding the proper application and interpretation of strength tests in ergonomics, especially among persons not thoroughly familiar with the limitations and caveats associated with the available procedures. The purpose of this chapter is to discuss some of the fundamental principles of strength assessment in ergonomics, so that these procedures can be better applied to control the risk of musculoskeletal disorders in the workplace 1.1. What is Strength? (And what are we Measuring?) Many of the complications associated with strength assessment arise from the simple fact that even our most sophisticated machinery does not directly measure the force or tension developed by a muscle in a living person. Instead, we can only observe the consequences of force development by a contracting muscle, or more likely, by a combination of muscles There are many ways in which we can measure the effects of muscular contraction, and the techniques we use can have a dramatic impact on the strength readings we will obtain. Consider the situation illustrated in Figure 1. In this example, the muscle exerts a constant force of 1000 Newtons (N). However, the forces we measure can vary quite dramatically depending on where we place the force cuff - from 167 N if we place it near the wrist to 500 N if we place it near the elbow. Which value should we select as properly representing the muscular strength for this elbow flexion exertion? The preceding example illustrates some important points with regard to strength assessment. Perhaps the most important is that "muscular strength is what is measured by an instrument" (Kroemer et al. 1999). It should also be clear from this example [ ] that two researchers could perform an elbow flexion strength experiqent on the same group of subjects, but if each selected different force cuff positions, they might end up with wildly differing estimates of strength. Differences in the strengths of various muscle groups in the published literature may be the results of differences in the procedures and measurement methods used by the experimenters Thus, it is critical that any strength data presented be accompanied by a detailed account of the manner in which the data were obtained. A few additional points need to be made with regard to the testing of human strength. We must be clear that what we are obtaining in such tests are not a person's maximal strength capability, but their maximal voluntary strength. The voluntary nature of the exertion introduces an unknown, but surely substantial, amount of variability in our measurements of strength. One can imagine two subjects with identical muscular strength capabilities, but with varying levels of motivation or discomfort tolerance, for example. We are likely to observe considerable differences in the voluntary force exerted by the two, but it should be understood that such results may be largely the result of psychological factors, and not differences m muscular strength per se. The important point to be made here is that not only are we unable to directly measure muscular force, what we are able to measure is modified by an invisible filter - a filter subject to a wide variety of influences and which will differ considerably for every person we test To make matters worse, this filter would be expected to change even within a given individual on a given day. From the foregoing discussion, one can perhaps better appreciate some of the difficulties with establishing a definitive relationship between an individual's measured strength and that individual's risk of injury.

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By S. E. Khalafalla

The extremely sluggish oxidation of steel scrap was appreciably accelerated when the charge was pretreated in aqueous solutions of sodium metavanadate or sodium molybdate. The degree of oxidation acceleration was inversely correlated with the melting point of the promoter oxide possessing the highest valency. The magnitude of oxidation enhancement exhibited a systematic inverse dependence on the duration of pickling processes; mere dipping of the oxidizable charge in the vanadate bath was most effective. In general, the rate of steel scrap oxidation increased with increasing concentration of the pickling reagent. The results are explained on the basis of the hydrolytic decomposition of the pickling agent with subsequent slow interaction with the metal surface, coupled with the tendency of vanadium to form polyanions in alkaline media. The data not only served to elucidate the mechanism by which catastrophic oxidation takes place, but also showed that the accelerating species need not be alloyed with the oxidizable metal; surface impregnation by minute amounts of the accelerating species can still produce catastrophic effects.

Jan 1, 1970

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

Predict the spontaneous combustion potential of a mining operation using an expert system computer program.

Jan 1, 1994

By Forrest T. Moyer

General injury experience in the mineral fuel industries was less favorable in 1965. Of the major industry groups, the coal mining and the coke industries had higher injury-frequency and severity rates than in 1964. The oil and gas industries had an increased Tate of occurrence of injuries although the severity rate improved. However, in the relatively small peat and native asphalt industries, the injury experience was more favorable than in 1964. Overall operating activity for the mineral fuel industries, as measured by the average number of men working daily and the total worktime, was higher than in 1964. Moderate declines in employment and worktime in the coal and peat industries were more than offset by gain in the other groups. In addition to the industry classifications included in this chapter, similar injury, employment, and worktime data on the metal, nonmetal, stone and aggregate industries are presented in volume I. Corresponding data for broad classifications of mineral industry groups arc given by States in volume III of the Minerals Yearbook.

Jan 1, 1967

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the charcoals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

3. Preliminary Evaluation of Mine Sealing Techniques As the first stage in the development of a technique for the remote sealing of mines, a state-of-the-art survey of various mine sealing techniques was conducted. This was expanded to include a review of different materials offering some potential for use as a mine sealant. Techniques for the remote placement of materials for other applications were evaluated, and system concepts for dis¬tributing remotely placed materials were developed. This preliminary review led to the development of a functional description of a general mine sealing technique to meet the specified conditions. Various potential system configurations were synthesized. These were subjected to a preliminary evaluation based on estimated confidence in system performance, development risk, cost, and sealing time. Based on this preliminary evaluation, promising mine¬sealing techniques were selected for further development. This section presents a review of the following: (a) Techniques for constructing permanent seals from within a mine. (b) State of the art in remote sealing for mine fire control. (c) Techniques for remote placement of materials for other applications. (d) Systems for distributing remotely placed material. (e) Materials for mine sealing. (f) Synthesis of remote mine sealing concepts.

Jan 1, 1973

By V. A. Marple, K. L. Rubow

"IntroductionA particle dispersion system has been developed to aerosolize bulk powders or material deposited on surfaces such as filters. The size distribution of the aerosolized particles can then be obtained by sampling the particles with an aerosol sizing instrument such as a TSI aerodynamic particle sizer (APS) or a cascade impactor.Of particular interest is the applicability of using this technique to obtain the size distribution of particles collected on filters. This system has been used to determine the size distribution of coal dust particle collected on membrane filters. The use of this device in this application is quite intriguing in that, if this technique can be shown to accurately determine the size distribution of airborne particles, one can easily collect particle samples using either personal or area particle samplers, determine the mass concentration of the collected material through gravimetric techniques and then use the particle dispersion system coupled with the APS to determine the particle size distribution. With this technique one can determine the particle size of dust in environments, such as underground mines, where it would be inconvenient or impossible to use a particle sizing instrument.Particle Dispersion SystemA prototype particle dispersion system has been developed for aerosolizing particles. A schematic diagram of the system is shown in Figure 1. The system consists of mechanism for advancing the particle sample beneath a dust pickup tube, a venturi for deagglomerating the particles, and a instrument for analyzing the aerosolized particulate matter.The procedure to analyze a particle sample is as follows. The particles to be aerosolized are placed on a sample plate from where the particles are picked up by an air stream flowing upward in a small capillary tube (dust pickup tube). This tube operates as a small vacuum cleaner passing over the sample plate. The air is drawn up the capillary tube at a rate of 2 L/m by a venturi aspirator. This is accomplished by placing the outlet of the capillary tube near the throat of the venturi. The accelerated velocity of the air creates a low pressure in this region which draws flow up the capillary tube. From the outlet of the capillary tube particles are transported to the inlet of the APS where a small fraction are sampled and the aerodynamic diameter of the particles determined. The particles which are not measured by the APS are passed into a HEPA filter."

Mar 1, 1989

By Ronald D. Hill, Elmore C. Grim

1.In 1972 over 595 million tons (51+0 million metric tons) of bituminous coal were mined; 49% of this tonnage was obtained by surface mining methods. Authorities have predicted that the tonnage of surface mined coal will increase in the future, especially since oil and gas resources are becoming limited. 2. Demands for clean air have increased mining activities in the low-sulfur coal deposits in the West. Pollution problems arising from these operations will be considerably different than those found in the East. The deposits are located in arid to semi-arid regions. Coal seams are generally aquifers and are a principle source of fresh water. Therefore mining may result in alteration of groundwater distribution patterns by aquifer disruption. In general, pollution problems associated with western mining are not well characterized. 3.Since any disturbance of the surface will alter the environment in the vicinity of the disturbance, pre-mining planning is a prerequisite to any environmentally successful surface mining operation. If properly carried out, the adverse social, economic, and environmental effects of coal surface mining will be minimized. Certain land areas will be unsuitable for surface mining where: a.Reclamation is not physically or economically possible. b.Mining is incompatible with existing land use plans. c.The proposed mining area is of critical environmental concern. Core drilling is the most satisfactory method of obtaining accurate information for pre-mining planning. 4. Unaccountable strip mining in the past has created problems that are still present today. Contour mining methods that involve the indiscriminate dumping of overburden on the downslope is one of the largest single sources of sediment from strip mining. However, land disturbed by strip mining can be reclaimed. Techniques have been and are being developed by which mining and reclamation are integrated into a single operation. Mountain top removal, head-of-hollow fill, and block cutting are examples in contour surface mining. These methods drastically reduce pollution problems associated with contour stripping.

Jan 1, 1974