Search Documents

By John C. Holtz

The Bureau of Mines studied air contamination caused by diesel exhaust in a 10,000-ft ventilated tunnel. Sequential air samples were taken at the ends and middle of the tunnel during an operating cycle. Observed and calculated results for carbon dioxide, carbon monoxide, and nitrogen oxides were essentially in agreement. Nitrogen dioxide was present only in trace amounts. It was found that contamination was related to the volume of ventilating air, the number of haulage trips, train speed, and engine load.

Jan 1, 1968

By Michael J. Gallagher

Diamond-bit performance data accumulated by the Bureau of Mines in core-drilling limestone and dolomite show that the physical characteristics of the diamonds and the sizes and types of bits used are economically significant. An analysis of the data establishes one trend of particular significance to those engaged in core drilling: Bits set with small, low-quality drill bort are the most economical. Detailed analysis of the factors that affect diamond-bit performance, such as size and quality of diamonds, sizes and types of bits, percentage of core recovered, and physical characteristics of bit matrices are assessed in the tables, bar charts, and discussion.

Jan 1, 1958

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By Lloyd A. Morley, Robert Stefanko

This report has presented a literature review of explosion proof¬ing of coal mine electrical equipment. The international "state-of¬the-art" is an extremely difficult definition to quantify but, from the preceding paragraphs, it is evident the international community be¬lieves that it is represented by the International Electrotechnical Commission's Publications. Five questions were set forth during the beginning of this report. Each will be evaluated in light of the preceding discussion. 1. Can Schedule 2G specifications on explosion-proof containers be substantiated? Literature was found in the three main problem areas, surface temperature, mechanical strength, and explosion transmission, to determine this. Surface temperature requirements are adequate except for equipment that can normally overload, and the required intern¬al pressure does afford some margin of safety. However, in terms of safety, gap dimensions are about ten times smaller than that needed. 2. Is it possible to replace the Schedule's design requirements with performance specifications? Two primary areas were determined as mechanical strength and explosion transmission. As was mentioned, for present flange and gap standards, the 150 psig requirement is adequate. Furthermore, it is the authors' opinion that the level cannot be re¬duced if the present gap requirements are retained. The Schedule now requires that 16 tests be run, but the literature suggests that only from three to six examinations are necessary. Then by using the abso¬lute maximum pressure from these measurements or 150 psig, whichever is

Jan 1, 1974

By David P. Lindroth

The heat content above 25.0° C up to 1,000° C was measured for six rock types: St. Cloud Gray Granodiorite, Holston Limestone, Sioux Quartzite, Rockville Quartz Monzonite, Salem Limestone, and the basalt at Dresser, Wis. The calorimetric data were obtained with an isothermal jacket-copper block calorimeter. The experimental heat content data for each rock type are presented, along with specific heat data obtained from the temperature derivative of the heat content. For the six rock types the maximum deviations of the specific heats at a given temperature were within 10 percent below 575° C and within 34 percent above 5750°C. The increase in the values of specific heat range from a minimum of 13 percent for the basalt at Dresser, Wis. (temperature range, 100° to 1,000° C) to a maximum of 46 percent for Holston Limestone (temperature range, 100° to 870° C).

Jan 1, 1971

Several short color films describing new technology developed through Bureau of Mines research are available on a loan basis. The films review results of Bureau research programs aimed at aiding the minerals industry by increasing mine productivity, ensuring worker health and safety, and enhancing minerals recovery, processing and recycling. Most of the films are available in a choice of for mats: 16mm film, ½" VHS cassette tape, or ¾" U-matic tape. The films are loaned by the Bureau of Mines free of charge; borrowers are requested to pay only the return postage and for any damage to the films. All titles are also available for purchase in 16mm or videotape formats. Interested persons wishing to borrow or purchase a film should specify its title and the preferred and alternate showing dates. All requests should be addressed to: Motion Picture Library Bureau of Mines Cochrans Mill Road P.O. Box 18070 Pittsburgh, PA 15236 A short description of each film follows: Safer Coal Mining Equipment Traces the development of modified conventional and continuous mining equipment, beginning with an investigation of the problems encountered with mining equipment and continuing through long-term testing of the modified equipment in two mines. "Human engineered" coal mining machines are shown in operation. These machines include features such as adjustable cabs, easy access controls, improved illumination, and other safety improvements. (19 min)

Jan 1, 1986

By J. Hudy

The performance of six dense-medium washers was evaluated in five preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation; and one plant was equipped with a two-compartment washer effecting two separations in one vessel. The separate secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The two-compartment washer produced a premium anthracite product and a middlings product. The sharpness-of-separation values ranged from good to excellent for the five primary separations and for the secondary separation.

Jan 1, 1968

This chapter describes the adverse health effects associated with exposure to respirable coal mine dust. Epidemiological studies of underground and surface coal miners in the United States and other countries are discussed. Also discussed are animal studies that add to our understanding of particle deposition and retention in the lungs and associated disease responses. This chapter emphasizes studies that (1) were performed since the passage of the Federal Coal Mine Health and Safety Act of 1969 [P.L. 91- 173], (2) used standardized methods of exposure monitoring and disease classification, and (3) investigated exposure-response relationships between respirable coal mine dust exposure and disease. Several published review articles contain further discussion of health effects studies of coal miners [Attfield and Wagner 1992b; Petsonk and Attfield 1994; Cotes and Steel 1987; Merchant et al. 1986; Morgan and Lapp 1976; Morgan 1975].

Jan 1, 1997

By T. W. Goodman, J. Cervik

The Bureau of Mines conducted studies to compare the effectiveness of the cross-measure borehole system with that of surface gob holes on two successively mined retreating longwalls in the Lower Kittanning Coalbed. Only the cross-measure system was in operation on panel A; on panel B, both systems were in operation. In addition, the cross-measure bore-holes on panel B were drilled parallel to the face, whereas those on panel A were drilled at a 45O angle with respect to the longwall axis. The studies show that the cross-measure system captured 71 pct of the methane generated by longwall mining on panel A. On panel B, the sur- face gob hole dominated over the cross-measure system for about 700 ft (213 m) after it was intercepted. Beyond that point, the cross-measure system dominated. About 93 pct of the methane generated on panel B was captured by the two systems. Cross-measure boreholes that were drilled parallel to the face were as effective as boreholes oriented 45" with respect to the longwall axis. In addition, they are shorter and require less drilling time. Comparison between observed gas pressure differentials in boreholes and calculated values indicate that boreholes can be shortened further to 140 ft (43 m). Additional studies are needed to verify these calculations.

Jan 1, 1986

By R. E. Mussler

Electrowinning of copper from chloride solutions in a diaphragm cell was studied by the Bureau of Mines. The copper powder product was shaken periodically from the cathode and removed from the bottom of the cell. The effects of copper concentration, brine concentration, copper chloride species, and cell voltage were investigated. Power consumption of 1.1 and 2.1 kW-hr/kg were obtained with cuprous and cupric chloride solutions, respectively.

Jan 1, 1975

By Gordon H. Dechman

This Bureau of Mines report presents an iterative approximation method for microseismic source location that was developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems, such as slope failure in an open pit mine. The source location method and two derivative location algorithms are described in detail, and the speed and accuracy of the two algorithms are compared.

Jan 1, 1977

By W. M. Merritts, Charles Findlay, Stephen Krickovic

Methane emission rates were studied in a Pittsburgh coalbed mine in northern West Virginia. A fullface boring-type continuous miner, equipped with a methane monitor, was used in the development of a set of eight main headings, one side of which was near old workings; the other side abutted virgin coal. Two air splits ventilated the section. Air volumes and methane percentages were recorded, and time studies of the miner were made during five consecutive operating days, during which a complete cycle of mining the headings and one line of related breakthroughs was accomplished. Methane emission rates increased significantly as mining progressed from the side near old mine workings toward the virgin area, and generally increased with coal extract ion. Mining in the heading immediately adjacent to virgin coal was interrupted quite frequently, owing to excessive methane concentrations at the face, despite adequate air volumes and acceptable methane concentrations in the immediate return airway.

Aug 1, 1970

By J. Nielen van der Merwe

The move toward partial pillar extraction versus full pillar extraction has necessitated a new approach to underground section stability. When pillars are mined too small to support the weight of the overburden, they will, in some cases, remain stable for a considerable period; in other cases, they will collapse unexpectedly and violently. There is no discernable difference between the pillar safety factors of the failed and stable cases. The explanation lies in the characteristics of the overburden layers. A method is proposed that recognizes the overburden characteristics in the evaluation of stability. Two stability factors are calculated: one for the pillars, the other for the overburden. Using this method, it is possible to make use of the bridging capabilities of overburden layers to prevent pillar collapse. It is possible to scientifically design partial pillar extraction layouts that will be safe. Using energy considerations, it is also possible to prevent violent failure of pillars.

Jan 5, 1999

By Bernard Lewis, Guenther von Elbe

"Explosive gas mixtures are characterized by their ability to undergo a self-accelerating reaction that may culminate in ignition. In the case of methane and air there are two interdependent causes of this acceleration. First, if a sufficiently fast reaction is induced, heat may be evolved faster than it is lost to the surroundings; consequently, the temperature rises and the reaction rate increases. Second, the reaction rate is determined not only by temperature but by the concentration of reactive intermediate products if the latter increases during the course of the reaction the rate will increase. To understand the role of these active intermediates, it should be realized that molecules of methane and oxygen, per se, show little tendency to react with each other even at high temperatures.(1) If, however, free radicals like OH and CH3, are present in the mixture, the methane and oxygen are attacked in the reactions(2):In these reactions the radicals are regenerated, and thus a chain of reactions is set up by an individual radical or chain carrier which is broken only if the latter is destroyed in some process. Not all collisions of a chain carrier with CH4 or 02 result in reaction, since one requirement for a successful collision is that the colliding particles have a certain minimum energy. The percentage of collisions in which this energy condition is fulfilled increases with temperature, so that for equal chain-breaking probabilities the length of the reaction chain increases with increasing temperature. Thus, there exists an interplay of temperature and concentration of chain carriers that determines the reaction rate. To carry the rate to the stage of self-acceleration, higher temperatures are required for lower than for higher chain-carrier concentrations, other conditions being equal."

Sep 1, 1939

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

By Robert R. Stein, Roy C. Bartholomae, William W. Aljoe

This Bureau of Mines report describes in detail the design and operation of a test apparatus for measuring the sound power levels of drills used by the mining industry. The two major components of the test apparatus are a computer-controlled automated drill test fixture (ADTF) and a large (45,000-ft3) reverberation chamber that houses the ADTF. Design specifications and performance capabilities of the ADTF and the reverberation room are given. Initial test results for three types of drills--a pneumatic percussion drill, a hydraulic percussion drill, and a pneumatic rotary drill--are given to illustrate the types of experiments that can be conducted with the test appartus.

By Nicholas P. Kripakov

The U.S. Bureau of Mines examined the applicability of existing material models to solve practical geotechnical mining-related problems by solving a yielding pillar stability problem considering confining effects on strength. Numerical difficulties normally encountered with modeling strain softening behavior were eased with a simplified computational procedure using a quasi-elastic approach to account for residual strength after initial failure. Although in agreement with a confined-core pillar design method using actual mine conditions that include mine layout geometry, overburden geology, and rock properties of the deposit and surrounding structure, the results cannot be verified because measured field data are not available at this writing.

Jan 1, 1981

By John J. Sammarco

As part of a project to automate coal extraction, computer control of a continuous mining machine test bed has been developed and tested by the Bureau of Mines. A computer system and control software were developed for accurate positioning of the conveyor elevation and swing, stabilizer jack, gathering head, and shear elevation. Tramming actions are also controlled by the computer. The computer system was designed to access data from sensors installed on a continuous miner and to interface with the existing control circuits of the miner. Testing in free space was used to characterize the operation of the machine. From this information, control algorithms were written and stored in the computer. The ability to control each function of the continuous miner with a high degree of accuracy and stability was successfully demonstrated in a series of tests in free space and in mining a block of simulated coal. In the mining of simulated coal, the cutting drum was instructed to position the shearer at the top of the block and shear down to the bottom under closed loop control. The cutting drum came within 0.27 in of the top and within 0.49 in of the bottom of the block for this shearing test.

Jan 1, 1988

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

California's coal resources are estimated to be 100 million tons, of which 50 percent is lignite, 40 percent subbituminous, and 10 percent bituminous. The occurrence of coal in California is rather limited and is restricted generally to the foothill regions of the western slopes of the Sierra Nevada Mountains. Significant quantities of coal have been mined in five areas: Ione in Amador County, Alberhill in Riverside County, Stone Canyon in Monterey County, CorralHollow in Alarneda County, and Mount Diablo in Contra Costa County. Most of the coal was rnined in the early 1900s and was used locally for fuel. Current mining operations are located in Amador County near the city of Ione. The two producing mines supply fuel to a mine-mouth co-generation power plant. The fuel coal is processed prior to burning to extract montan wax. Because California does not have primacy, coal mining in the state is regulated by the Office of Surface Mining's Albuquerque, New Mexico, Field Office.

Jan 1, 1992